Range Rover Classic Parts

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Glovebox Lock Set secures the glovebox lid in the closed position and is released by key. It mounts in the glovebox within the facia, forming part ...

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Non-Return Valve for the V8 petrol engine, fitted to the inlet manifold vacuum take-off. The valve allows air to be drawn one way from the vacuum ...

Bolt - M6 x 30mm is a metric threaded fastener with a 6 mm nominal thread diameter and a 30 mm shank length. It secures bolted joints where an M6 ...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Locking Washer of the Starlock (shakeproof) type, a push-on retainer used to hold a component onto a plain shaft or to lock a fastener against vibr...

Flywheel Bolt, 7/16" UNC x 1" hexagonal head, securing the flywheel to the rear crankshaft flange. Used on V8 petrol engines with manual transmiss...

Window regulator front RH

Circlip - LT77 Selector Shaft for the LT77 5-speed manual gearbox. This circlip retains the selector shaft within the gear selector and shaft asse...

Warning Label A warning label relating to the battery negative (earth) cable connection. It is applied in the vehicle to convey a safety instructi...

Washer - a general-purpose fixing washer used across multiple body, brake and chassis assemblies. It spreads the clamping load of a bolt or nut ov...

Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...

Rear Side Door Channel is a glass run channel mounted within the rear side door, fitted to the right-hand (RH) side. The channel locates and guide...

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Sedimentor O-Ring for the diesel fuel filter assembly. This rubber sealing ring seals the sedimentor bowl against the filter head, preventing fuel...

Retaining Clip for the front door lock, also known as the door lock plate.

Air Deflector for the carburettor air intake on the 3.5L V8 carburettor engine. Part of the heated-air intake arrangement, it directs warmed air t...

Core Plug - Cylinder Block Expansion Port is a pressed-steel sealing plug installed in the outer face of the cylinder block to close the casting ap...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Door Hinge - Lower for the front door, mounted to the A-pillar to support and align the lower section of the door. Works in conjunction with the up...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Torque Converter Housing Cover Gasket for the automatic transmission bell housing. It seals the lower access cover on the torque converter housing...

Seal Washer - Turbocharger Copper sealing washer for the turbocharger oil feed circuit. It seals the banjo union on the turbocharger's oil supply ...

Accelerator Cable for the Range Rover Classic 3.5L V8 carburettor engine, left-hand drive, manual transmission. This cable connects the accelerato...

Exhaust Bracket for the exhaust mounting system. This bracket supports the exhaust line at the section immediately behind the front silencer, loca...

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

M6 Stud for the gearbox main casing. This threaded stud secures the speedometer drive housing to the transmission main casing, providing the fixin...

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

Heater Bypass Coolant Valve for V8 petrol applications. This vacuum-operated valve is installed in the HVAC coolant circuit and controls the flow ...

Torsion Spring Sleeve for the lower tailgate. It fits over the tailgate torsion spring, forming a protective bearing sleeve at the pivot and preven...

Cable Tie for securing wiring looms and cables in Land Rover applications.

Filler and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Grommet - rubber sealing grommet, 3/4 inch overall diameter with 1/8 inch centre hole. Used to seal and protect wiring cables where they pass thro...

Nutsert - 5/16" UNF is a blind rivet nut (rivnut) with a 5/16" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal ...

Rocker Cover O-Ring for the VM four-cylinder turbo diesel engine, sealing the rocker (cam) cover to the cylinder head. It maintains the oil-tight ...

Spire Nut, a J-type sheet-metal spring nut (also known as a speed nut) used to secure trim, panels and fittings. The nut clips over a panel edge o...

Screw - a No. 10 x 1" pan-head self-tapping screw used across interior and door assemblies. It secures the window regulator and door glass channel...

Locking Wheel Nut Set for alloy wheels that use the original alloy wheel nuts, securing the road wheels against theft. The set includes 5 locking ...

Rivet is a body fixing used to secure sheet-metal panels, wheelarch liners and trim to the vehicle structure. It forms a permanent, vibration-resi...

Thermostat regulates coolant flow within the engine cooling circuit of the 2.5L 4-cylinder VM Turbo Diesel. Housed in the thermostat housing at th...

Clevis pin

Crankshaft Bolt is the retaining bolt that secures the pulley and damper assembly to the nose of the crankshaft on the V8 petrol engine. Threaded ...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Clutch Cap that closes an aperture in the clutch bellhousing around the release mechanism. Fitted over an opening in the bellhousing, the cap seal...

Swivel Pin Retaining Bolt A fixing bolt for the front axle swivel pin housing. It secures a swivel pin to the swivel pin housing, retaining the pi...