Range Rover Classic Parts

Joint Steering Upper

Radius Arm Bush mounts at the axle end of the front radius arm, within the front suspension radius arm and axle location assembly. It forms the co...

Screw: pan head self-tapping screw.

Drive Flange Nut - replacement centre nut for the heavy-duty thin-type drive flange, black finish. The drive flange sits at the outer end of the f...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Nut FQA

Suspension Bush - Rear Lower, polyurethane, supplied as a set of two bushes with internal sleeves and installation grease for the axle-end mounting...

Plain Washer - Swivel Pin Housing is a flat washer used within the front axle swivel pin housing assembly. It seats beneath the housing fixing bolt...

Body Aperture Harness Grommet for the wiring harness routing assembly. Rubber grommet installed in a body panel aperture to seal and protect wirin...

Protective Coating Kit - Tintable (4 L) for applying a durable, textured surface coating to body panels, underbody areas, wheel arches, load beds, ...

Viscous Fan Coupling - temperature-sensitive drive coupling between the water pump drive and the engine cooling fan. It modulates fan speed with u...

Clutch Master Cylinder for the clutch hydraulic circuit, installed at the pedal box. The cylinder converts mechanical clutch-pedal movement into h...

Screw for securing the engine wiring harness in Rover V8 petrol engine installations. Fastens harness clips and mounting brackets to the engine bl...

Clutch Slave Cylinder for the manual transmission clutch release hydraulic circuit. It is fed by the clutch master cylinder and mounts at the gearb...

Fuse - 60A - high-current blade fuse for the main electrical protection circuits. Rated at 60 amps, this fuse protects high-draw circuits such as ...

Layshaft Bearing is the layshaft taper roller bearing for the LT77 and R380 5-speed manual gearbox. Located in the gearbox centre plate, it suppor...

Brake Union - Blanking Plug, male thread, M10 x 1mm, short body. Used in the metric hydraulic brake circuit to blank off an unused or redundant po...

Roll Pin for Door Hinge on the Range Rover Classic. A small cylindrical spring pin that locates and retains components within the door hinge assem...

Front Propshaft - Wide Angle, connecting the transfer case front output flange to the front axle differential input pinion. The wide angle joint d...

Circlip is a split retaining ring that locates on the reverse shaft of the LT95 gearbox. It seats into a machined groove to axially retain the rev...

Light Socket for the inspection lamp on Series Land Rover vehicles. This black bayonet-type bulb holder is used in the inspection lamp assembly, p...

Coupling Assembly - union fitting for the engine oil cooler pipe circuit. This union connects adjacent oil cooler pipe sections in the engine bay,...

Mainshaft Spacer - a spacer fitted to the gearbox mainshaft of the five-speed manual gearbox. It sets the axial position of the gears and bearings...

Mainshaft Nut Staked retaining nut securing the shaft assembly within the manual gearbox. Tightened and staked to lock the gearbox shaft component...

Shim

Rear Radius Arm Bush Kit - Chassis End, supplied as a set of four polyurethane bushes with retaining plates, inner sleeves, and installation grease...

Bush Kit - Front Radius Axle Arm End

Shock absorber rear early style, two halve bushes in upper eye, fitted to bracket using a large washer and a split pin.

Shock Absorber for the front suspension — the hydraulic damper that controls spring movement at the front axle. The damper resists and slows the c...

Shock Absorber Dis1/Range Rover Classic Rear

Rear Bumper End Cap for the left-hand end of the rear bumper assembly on the Range Rover Classic. Fits over the open end of the rear bumper tube, ...

Suspension Kit providing 2 inches of lift in a medium load configuration, combining rated coil springs with extended-travel Pro Sport shock absorbe...

Differential Pinion Flange Kit for the three-bolt drive flange on the axle differential. The pinion flange mounts on the differential pinion shaft...

Fuel Tank Retainer for the fuel tank mounting assembly. This retaining plate secures the fuel tank in position within its mounting location in the...

Vacuum Actuator O-Ring for the LT95 4-speed gearbox. This O-ring seals the vacuum actuator fitted to the LT95 transfer case mechanism, used on V8-p...

Sealing Washer seals the turbocharger oil drain pipe where it meets its adaptor on the engine block. It forms an oil-tight joint in the turbocharg...

Bolt - 1/4" UNC x 1-7/8" is a UNC hex head bolt used in the engine cooling and air conditioning systems of Land Rover vehicles fitted with the 3.5L...

Screw - 2BA x 1" is a round head screw in British Association (BA) thread form, 2BA size, 1 inch in length. Used throughout the Series Land Rover ...

Brake Caliper Bolt secures the rear brake caliper to its mounting bracket within the rear braking assembly. It clamps the caliper body in position...

Carburettor Throttle Linkage Roller for the 3.5L V8 twin-carburettor petrol engine. It runs on the throttle countershaft, guiding the carburettor ...

Bolt rear caliper 7/16" UNF

Pan Head Screw, M6 x 12mm. Metric pan head screw for use across a range of Land Rover body, chassis, and electrical assemblies.

Anti-Roll Bar Bush for the front suspension system, sold as a pair. This bush locates the anti-roll bar at its chassis mounting points, allowing t...

Crown Wheel & Pinion Set - the final-drive gear pair housed within the axle differential. The pinion takes drive from the propshaft and turns t...

Drain Plug Washer is the copper sealing washer for the drain plug on the LT77 manual gearbox. It seats between the magnetic drain plug and the gea...

Bleed Screw for the imperial-specification front and rear brake calipers on the Range Rover Classic. This imperial-thread bleed screw fits the cal...

Anti-Roll Bar Link & Shock Bush Kit renews the compliant mounting bushes in the anti-roll bar link and shock absorber mounting points within th...

Bulb and Holder for switch and control panel illumination. The orange-tinted bulb and its integral holder fit into the rear of dashboard switches ...