Range Rover Classic Parts

Plain Washer for M10 fasteners. A flat washer fitted under a bolt head or nut to distribute the clamping load across the joint face, spread bearin...

screw M5 x 12

Nyloc Nut with a 3/4" UNF thread, used as a locknut on heavy suspension joints. A nylon insert set into the crown of the nut deforms over the bolt...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Trim Clip is a panel-retaining fastener used to secure interior door casing and exterior bodyside and drip-rail trim to the body. Part of the body...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit on manual transmission applications. Mounted at the clutch housing, it receive...

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Swivel Ball Inner Bearing Housing for the front axle swivel assembly. It locates and supports the inner bearing within the swivel ball, maintaining...

Anti-Rattle Clip secures the linkage rod within the door latch and lock mechanism. It retains the lock linkage rod at its connection point, holdin...

Taper roller bearing for the swivel pin housing assembly within the front axle system. This bearing supports radial and axial loads generated at ...

Sealing Washer - copper sealing ring for the cooling system drain points. It seats under the radiator drain plug and the cylinder block drain tap, ...

Crankshaft Oil Seal seals the front timing cover where the crankshaft nose passes through it. Fitted to the 2.5L 300 TDi diesel engine, the seal r...

Rocker Cover Sealing Washer seals a rocker cover retaining bolt on the 200Tdi 2.5L turbo diesel engine. The washer fits under the rocker (valve) c...

Front Propshaft Flange Bolt Kit - the high-tensile fasteners that secure the front propshaft to its mating flanges at the transfer box and axle end...

Oil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Rear Shock Absorber, standard-travel, for the rear axle suspension. The damper controls vertical movement of the rear axle and damps spring oscill...

Camshaft Oil Seal - radial oil seal for the 2.5L 300 TDi turbo diesel engine, fitted in the front timing cover within the timing gear assembly. Th...

Washer 20mm

Fuel Pipe Clip securing fuel pipe within the fuel delivery system. The clip retains and locates the fuel line along its routing, holding it agains...

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

Track Rod End for the steering linkage, with a left-hand thread. The track rod end forms the ball-jointed connection between the steering link and...

Oil Temperature Transmitter for the engine instrumentation circuit. The transmitter threads into the oil gallery and varies its electrical resistan...

Oil Pump Gasket for the engine lubrication system, sealing the oil pump to its mounting face on the cylinder block. It maintains a leak-free joint...

Water Temperature Sender threads into the cooling system and measures engine coolant temperature, feeding the signal to the dashboard temperature g...

Plain Washer with a 6 mm (1/4") bore, a general-purpose flat washer for use with M6 fasteners. Fitted beneath a bolt head or nut to spread the cla...

Nyloc Nut with an M16 thread - a nylon-insert locking nut used on heavily loaded suspension and driveline fixings. A nylon collar set into the top...

Camshaft Oil Seal seals the camshaft on the 2.5L 4-cylinder diesel engines, including the 200TDi. Fitted at the front of the engine where the cams...

Bulb rated 12V 10W with a BA15S bayonet cap. A single-contact bayonet-fitting (BA15S) bulb for 12-volt circuits. The single-contact cap suits sing...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Air intake duct hose Def 2.5DT & 200TDi air cleaner to turbocharger

Lokut Nut is a self-locking nut used to secure the headlamp to the body at the front wing. The self-locking design resists loosening under vibrati...

Headlamp Body with manual headlamp levelling. The headlamp body is the housing and reflector unit that carries the headlamp light unit and mounts ...

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Bolt 1/4" UNF x 7/8" is a fixing bolt for the track rod and steering damper within the steering linkage. It clamps the track rod end and secures t...

High Note Horn, the high-pitched unit of the vehicle's dual-tone horn system. It sounds together with the low note horn to produce the two-tone au...

Tab Washer locks the drop arm retaining nut on the Adwest power steering box, its tab folded against a flat on the nut to stop it working loose und...

Ball Bearing for the transfer box, supporting the output shaft and its output flange. Fitted in the LT230 and NV225 transfer boxes, the bearing lo...

Hex-head bolt, 5/16" UNC thread, 1" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and socke...

Plain Washer - a flat, load-spreading washer with a 1/4 in (6 mm) bore and 5/8 in outside diameter, approximately 1/16 in thick, finished in Sherar...

Headlamp & Sidelight Switch is the master lighting switch in the exterior lighting circuit, mounted on the steering column. It provides the pr...

Drive Belt for the auxiliary (accessory) drive system of the 300 TDi turbo diesel engine. The belt transmits drive from the crankshaft pulley to th...

Headlamp Adjuster for the manual headlamp levelling system, fitted to the headlamp unit. It sets the vertical aim of the headlamp beam, allowing t...

Brake Caliper Repair Kit - 4-Piston

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Brake pipe clip

Speedo cable oil seal retainer plate

Carpet Drive Clip is an interior trim fastener used to retain the floor carpets against the body. The drive-clip design presses into a mounting ho...