Range Rover Classic Parts

Crankshaft Woodruff Key for the 2.5L 300TDi and 2.5L Td5 diesel engines. This semicircular key seats in a slot machined into the crankshaft nose an...

Timing Gear Housing Gasket for the 300 TDi engine, sealing the drain plate to the timing gear housing at the front of the engine. Forms the joint ...

Cylinder Head Gasket for the 2.5L 200 TDi and 300 TDi diesel engines, sealing the joint between the cylinder head and the engine block. It contain...

Drive Belt for the V8 petrol engine auxiliary drive - a 7-rib poly-V (7PK) serpentine belt measuring 1870 mm. Transfers crankshaft rotation to the...

Hydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...

Breather Filter is the crankcase ventilation filter mounted at the rocker cover on the V8 EFI petrol engine. It filters oil vapour and mist from t...

Viscous Fan Coupling is the temperature-controlled drive unit between the water pump and the engine cooling fan. It mounts on the water pump shaft...

Caliper Bolt is the fixing bolt that secures the brake caliper to its mounting bracket. The same bolt specification is used across several chassis...

High-Tensile Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/4" shank length. A hex-head fastener manufactured to a high-t...

Bolt 5/16" UNC x 5" is a long mounting bolt for the coolant pump and power steering pump on the 3.5L V8 petrol engine. Its length carries the powe...

Plain Washer M8

Power Steering Pump Seal Kit supplying the housing and drive shaft seals for the cast-bodied power steering pump. The pump gaskets are supplied se...

Carb overhaul kit 175CD V8 Zenith Stromberg

Lens RH

Camshaft Bearing for the 2nd, 3rd and 4th journal positions of the four-cylinder engine. The bearing shell is fitted into its housing in the cylind...

Nylon Stud, a trim retaining fastener used to hold interior trim panels and carpet in position. The stud pushes into a pilot hole in the body pane...

Power Steering Pump Belt in the engine accessory drive system, driving the power steering pump. The belt transfers rotation from the crankshaft pu...

Magnetic Drain Plug for the engine oil sump and the LT230 transfer box drain ports. The magnetised tip captures ferrous wear particles suspended i...

Lower Swivel Pin forming the lower pivot of the front axle swivel housing. The pin bolts to the underside of the swivel pin housing and carries th...

Clutch Slave Cylinder Repair Kit for the hydraulic clutch slave cylinder on the LT77 manual gearbox. The slave cylinder converts hydraulic pressur...

Bonnet Release Cable for the Range Rover Classic. This cable runs from the interior release handle to the bonnet catch, allowing the bonnet to be ...

Main Switch: heavy-duty main switch rated at 1000 A.

Split Pin locks slotted nuts, clevis pins and linkage joints against loosening, passing through a drilled hole and splayed to retain the assembly. ...

Tow Ball – 50 mm a black-finished towing ball for flange-type towing brackets. The ball bolts to the face of the towing bracket on the standard tw...

Upper Oil Cooler Pipe - feed pipe in the engine oil cooling circuit of the 4.0L V8 EFI petrol engine, carrying oil from the engine to the oil coole...

Fitment: All models (VIN) LA930456 on

Plain Washer - metric M8 plain washer for use in general fastening assemblies throughout the vehicle. A standard flat washer used to distribute lo...

Interior Trim Fastener in Bahama Beige, for securing rear interior trim panels in seven-seat Discovery 1 variants. This plastic push-in fastener c...

Spring Washer for use across a wide range of fixings and assembly applications on Land Rover vehicles. This split-ring spring washer is placed ben...

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Bolt - a hexagonal-head bolt with an M6 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the vehicl...

Body Rivet - a mechanical fastener used within the body and panel assembly to join thin sheet metal, trim and stowage fittings. Nominal size 3/16"...

Flat plain washer used within general fastening applications across multiple vehicle assemblies, providing a load distribution surface between the ...

Steering Wheel is a 15-inch three-spoke replacement wheel that mounts to the steering column. It is supplied without a boss, so a separate fitting...

Toebox Trim Fastener - the fixing that secures the footrest and toebox trim panel in the footwell. It retains the lower trim at the A-post and toe...

Coolant Pipe Adaptor for the engine cooling circuit. It threads into the thermostat housing / cylinder head coolant outlet to provide the connectio...

Upgrade or replace your steering wheel boss with this high-quality 36-tooth adapter, designed specifically for Land Rover Defender to 1991 90/110 v...

Hose Clip - 12-20mm worm-drive hose clip suitable for hoses with an outside diameter of 12 to 20mm. This stainless-steel screw-type clip tightens ...

Shock Absorber Bush Set for the shock absorber mountings. This set provides the bushes that locate each shock absorber at its mounting eyes, insul...

Stepper Motor is the idle air control stepper motor mounted on the inlet manifold plenum chamber of the V8 EFI petrol engine. Driven by the engine...

Track Rod End Boot Ring - spring retaining ring for the track rod end of the steering linkage. It clamps the rubber dust boot onto the track rod en...

Cooling Fan for the engine cooling assembly. Driven from the front of the engine through the viscous fan coupling, the fan draws air through the r...

Banjo Bolt is a hollow union bolt used in the fuel system of the 200 Tdi and 300 Tdi engines. It secures a banjo hose fitting at the injection pum...

Coolant Hose for the V8 carburettor petrol engine cooling circuit. It carries engine coolant between components of the cooling system, moulded to s...

Filler Plug in blue anodised aluminium, replacing the standard cooling system filler and blanking plug at the thermostat housing. Seals against a ...

Temperature Transmitter is the coolant temperature sender within the engine cooling and instrument gauge circuit, for V8 petrol applications and ca...

Cap Reservoir Br.m.cylinder

Power Steering Pipe O-Ring - a seal in the power steering hydraulic circuit. It fits at the union between a power steering pipe and its mating conn...