Range Rover Classic Parts

Fuel Filter Element for the carburettor fuel supply circuit on Land Rover V8 petrol engines. Fitted in-line on the fuel feed pipe between the fuel...

Capless Wedge Bulb, 12V 1.2W, for instrument, facia, clock and cigar-lighter illumination. The glass wedge base pushes directly into the panel hol...

Oil Pressure Switch for the V8 petrol engine, forming part of the engine oil pressure warning circuit within the lubrication system. The switch th...

Front door window regulator assembly for left-hand front door applications within the door glass operating mechanism. This component forms part o...

Washer Pump for the windscreen washer system, running on a 24-volt electrical supply. The pump draws fluid from the washer reservoir and delivers ...

Compression Olive for rigid fuel pipe unions. This 8 mm ferrule seats between the union nut and the fitting body, compressing onto the pipe as the ...

Shock Absorber Turret Bracket is the front suspension turret that caps the coil spring and carries the upper mounting of the front shock absorber. ...

Rotor Arm for the distributor ignition system. The rotor arm mounts on the top of the distributor shaft and turns with it. It picks up the high-te...

Condenser for the distributor ignition system. The condenser (capacitor) is wired across the contact breaker points inside the distributor. As the...

Courtesy Lamp Switch is the door-pillar plunger switch in the interior lighting circuit. Mounted in the door aperture, it is released when a door ...

Column Switch mounted on the steering column, combining the indicator (turn signal), horn and headlamp dip/main-beam functions in a single stalk-op...

Reverse & Differential Lock Switch is a plunger-operated switch used in the manual gearbox and transfer box electrical circuits. The same swit...

Nyloc Nut with a 3/4" UNF thread, used as a locknut on heavy suspension joints. A nylon insert set into the crown of the nut deforms over the bolt...

Radius Arm Cup Washer is the dished washer used at the front radius arm mounting, seating against the radius arm bush to spread the clamping load o...

Slipper pad

Transfer Box Flange Bolt - a 3/8" UNF x 1-1/4" hex-head bolt for the LT230 transfer case front output flange. It secures the drive flange to the f...

Bolt - a metric hexagon-head bolt measuring M10 x 110mm. This is a general-purpose threaded fixing used at structural and chassis mounting points,...

Engine Mounting Rubber is a bonded rubber-to-metal isolator in the powertrain mounting assembly. It sits between the mounting bracket and the chass...

Speedo drive oil seal LT230

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Shock Absorber Washer for the rear suspension, outer position. This washer fits over the rear shock absorber mounting, seating against the rubber ...

Joint Washer sealing the mounting joint between the cylinder block and the auxiliary unit driven off the engine: the vacuum pump on diesel engines,...

Rocker Cover Gasket for the 2.5L 300TDi diesel engine, sealing the interface between the rocker cover and the cylinder head. Installed at the top ...

Drop Arm Ball Joint Kit for renewing the ball joint that connects the steering box drop arm to the drag link. The joint transmits steering input f...

Drag Link Ball Joint Kit for the steering box drop arm on power-assisted steering boxes. The ball joint forms the articulating connection between ...

Differential Pinion Oil Seal for the final drive, with a 4-bolt flange (LR-type, non-Salisbury axle). The single-lip seal sits at the front of the ...

Flange Bolt, M8 x 50 mm - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing ...

Transmission Handbrake Shoe Set is the friction pair for the drum-type parking brake mounted on the rear output of the transfer box. When the hand...

Drive Pin Fastener is a two-piece push-in fixing used to retain interior trim and ducting panels. The fastener body is pushed through aligned hole...

Gas Strut for the upper tailgate, part of the rear tailgate assembly. This gas-filled strut supports the weight of the upper tailgate as it is rai...

Swivel Shim is a 0.75 mm selective shim from the front axle swivel pin assembly. It is fitted beneath the upper swivel pin retaining plate, where s...

Swivel Pin Housing Shim - 0.13mm (0.005") for the front axle swivel pin housing assembly. This precision shim is fitted between the swivel pin hou...

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the 300 TDi 2.5L diesel engine. It forms a coolant-tight joint...

Rubber Mounting A flexible rubber isolation mount used in the exhaust gas recirculation (EGR) system and air-cleaner assembly. It locates and supp...

O-Ring for the oil filter adaptor assembly on 4-cylinder petrol and diesel engines up to and including the 300TDi. This O-ring seals the joint bet...

Upper Spring Isolator for the coil spring suspension. This rubber seat sits at the upper end of the coil spring, between the top of the spring and ...

Diesel Fuel Filter - replaceable cartridge filter element for the fuel supply circuit on 200 TDi and 300 TDi diesel engines. The element sits in t...

Front Cover Gasket seals the timing cover to the front face of the cylinder block on the V8 petrol engine. It fits between the front cover and the...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Chassis Harness Grommet - black rubber grommet for the chassis wiring harness, 6 x 33.5mm. Fitted where the wiring harness passes through a chassi...

Inlet Manifold Seal sealing the inlet manifold to the cylinder block valley on the V8 petrol engine. This formed seal closes the manifold valley j...

LT230 Transfer Box Bottom Cover Gasket, sealing the main casing bottom cover of the LT230 two-speed transfer box. Fits the main casing bottom cove...

Mirror Adapter for the exterior door mirror assembly. This adaptor forms the interface between the mirror glass and the mirror body, locating the ...

Swivel Pin Housing Thrust Washer for the front axle swivel pin assembly. Installed within the swivel pin housing between the pin head and the hous...

O-Ring for the engine cooling system thermostat housing. This sealing ring fits the drain or filler plug on the thermostat housing, providing a le...

Brake Pipe Union - a male tube-nut fitting that secures a flared 3/16" (4.75mm) hydraulic pipe end into a female union, T-piece or cylinder port. ...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Front axle drive flange designed to connect the drive shaft to the wheel hub assembly. The flange transmits rotational force from the half shaft ...