Range Rover Classic Parts

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Gasket

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Valve Stem Seal - the seal fitted over the valve stem in the cylinder head to control the oil that passes down the stem into the port. This is the...

Bolt with a 3/8" UNC (Unified National Coarse) imperial thread and a 2" shank length. A hex-head fastener used in body, chassis and general assemb...

Camshaft Bearing for the 2nd, 3rd and 4th journal positions of the four-cylinder engine. The bearing shell is fitted into its housing in the cylind...

Camshaft Bearing Set comprises the plain bearing shells that support the camshaft within the cylinder block of the four-cylinder engine. The beari...

switch loss vacuum

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the carburettor throttle spindle. Transmits pedal movement ...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Transfer Box Sealing Ring - Locking Pin A rubber O-ring that seals the locking pin where it enters the transfer box case. It seals the selector lo...

Crankshaft Key locates the timing gear and crankshaft pulley on the crankshaft nose, fixing their angular position relative to the shaft. It trans...

Grommet seals and protects cables, harnesses and hoses where they pass through body and chassis panels. It is used at wiring harness pass-throughs...

Warning Label A warning label relating to the battery negative (earth) cable connection. It is applied in the vehicle to convey a safety instructi...

Screw hex HD 3/8" UNC x 1-1/4"

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Pas op alle  V8 benzine motoren met Stromberg carburateurs

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Main Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...

Bolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...

Starter Motor for V8 petrol engines, operating within the engine electrical starting system. The solenoid-actuated pinion engages the flywheel rin...

Water Pump circulates coolant through the engine cooling system. It mounts to the front of the Rover 3.5L V8 engine and is driven by the auxiliary...

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

Rocker Cover Breather Hose - Left-Hand for the crankcase ventilation system of the Rover 3.5L V8 twin-carburettor engine. This hose connects the l...

seal washer for block coolant drain plug. - All 4-cylinder engines upto 1998 (except VM diesel)

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Rocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...

Fuel Pump Adaptor for mounting the external fuel pump on petrol engines. It provides the interface between the external fuel pump and its mounting...

Plastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...

Gear Lever Damper for the LT95 four-speed gearbox gear-change mechanism. This damping washer fits at the base of the main gear lever, absorbing vi...

Special Bolt for retaining the tappets in the cylinder block, part of the camshaft and tappet assembly. This is a specific-design fastener that se...

Oil Pump Relief Valve Spring - sets the pressure at which the oil pump's relief valve opens. It holds the relief valve plunger closed against the ...

Filler and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...

Distributor O-Ring, the sealing ring for the ignition distributor on the 3.5L V8 petrol engine. The O-ring seals the distributor base where it loc...

Fuel Sedimentor is a water and sediment trap in the diesel fuel supply line, installed upstream of the fuel filter and injection pump. Fuel passes...

Sedimentor Drain Plug Seal for the sedimentor in the diesel fuel supply. The sedimentor separates water and heavier contaminants from the fuel ahea...

Nutsert - 5/16" UNF is a blind rivet nut (rivnut) with a 5/16" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal ...

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Cylinder Head Bolt - a 7/16" UNC x 2.71" medium-type bolt for the Rover V8, part of the cylinder head fixings. This is the medium-length head bolt...

Viscous Fan Assembly for the engine cooling system, mounting to the viscous coupling unit on the front of the engine. This 16", 7-blade white fan ...

Plain Washer - Large 5/16" is a large plain washer for use with 5/16" fastenings, providing load distribution beneath bolt heads and nuts across La...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Union Nut for the fuel pipe in the fuel delivery system. This M12 union nut clamps a fuel pipe to its mating union or component port, drawing the ...

Left-Hand Exhaust Downpipe for the 3.5L V8 EFI engine, non-catalyst exhaust configuration. Connects the left cylinder bank exhaust manifold outlet ...

Fuel Tank Drain Plug - the threaded plug that seals the drain point at the base of the fuel tank. Removing it allows the tank to be drained for se...