Range Rover Classic Parts

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

Serrated Washer with a 3/8" bore, a serrated locking (shakeproof) washer. Fitted beneath a bolt head or nut, the serrated teeth bite into both the...

Washer Pump for the windscreen washer system, running on a 24-volt electrical supply. The pump draws fluid from the washer reservoir and delivers ...

Rotor Arm for the distributor ignition system. The rotor arm mounts on the top of the distributor shaft and turns with it. It picks up the high-te...

Condenser for the distributor ignition system. The condenser (capacitor) is wired across the contact breaker points inside the distributor. As the...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Shock Absorber Washer for the rear suspension, outer position. This washer fits over the rear shock absorber mounting, seating against the rubber ...

Flange Bolt, M8 x 50 mm - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing ...

Drive Pin Fastener is a two-piece push-in fixing used to retain interior trim and ducting panels. The fastener body is pushed through aligned hole...

Front Cover Gasket seals the timing cover to the front face of the cylinder block on the V8 petrol engine. It fits between the front cover and the...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Chassis Harness Grommet - black rubber grommet for the chassis wiring harness, 6 x 33.5mm. Fitted where the wiring harness passes through a chassi...

Brake Pipe Union - a male tube-nut fitting that secures a flared 3/16" (4.75mm) hydraulic pipe end into a female union, T-piece or cylinder port. ...

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face on diesel engines. The side cover closes the p...

Toggle Switch is a two-position on/off switch in the dashboard switchgear, controlling the instrument and panel lighting circuit. The sprung toggl...

Thermostat 74C

This camshaft sprocket is designed for Land Rover V8 engines, providing precise timing and reliable performance.

Sump Plug seals the drain aperture at the base of the engine sump, retaining the engine oil and providing the drain point for an oil change. Remov...

Cylinder Block Drain Tap threads into the coolant jacket of the cylinder block, providing a controlled drain point for the engine cooling system. ...

Rocker Cover Gasket for the V8 petrol engine, cork construction. The gasket seals the joint between the rocker cover and the cylinder head, contai...

Instrument Panel Bulb, rated 12V 2W with a BA7s bayonet base (type 281), for the instrument cluster lighting circuit. It provides the internal ill...

Relay - 12V automotive changeover relay with a 30A contact rating, twin make. The five-pin configuration provides two normally-open contacts, allo...

Swivel Housing Washer for the swivel pin housing drain plug, part of the front axle swivel assembly. The sealing washer fits beneath the drain plu...

Clutch Release Fork Kit for the manual transmission clutch release mechanism, built around a cast release fork. The fork pivots on its mounting in...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Track Rod End Boot for the steering track rod end ball joint. This rubber boot fits over the track rod end housing, sealing the ball joint against...

Hex Nut, 7/16" UNF, plain steel. This full hex nut secures the door top to the door base on Series models and is used at other 7/16" UNF fixing po...

Stop Light Switch mounts at the brake pedal and switches the rear brake (stop) lamps on when the pedal is depressed, operating within the brake-lig...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Hex-head bolt, 5/16" UNF thread, 1" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and sockets...

7" round LED headlamp 12/24V chrome 78W LHD (pair)

Handbrake Pull-Off Spring for the transmission-mounted drum handbrake assembly. This return spring retracts the brake shoes against the backplate ...

Bolt 5/16" UNF x 2" is a hex-head set bolt with a 5/16-inch Unified National Fine (UNF) thread at 24 threads per inch and a 2-inch shank length. I...

Gearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...

Locking plate

Hex Nut, 3/8" UNF. A general-purpose threaded fastener used at fixing points across the braking, chassis and body assemblies. The 3/8" Unified Nat...

Steering Box is the recirculating-ball power steering gear at the heart of the steering system, converting rotation of the steering column into the...

Lock Washer secures a threaded fastener against loosening under vibration and thermal cycling. Fitted beneath the nut or bolt head, it bites into ...

Brake Pipe Union - a female union fitting for 3/16" (4.75mm) hydraulic brake pipe, with an M10 x 1mm thread. Machined from brass, it threads onto ...

Oil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

Water Temperature Sender threads into the cooling system and measures engine coolant temperature, feeding the signal to the dashboard temperature g...

Hex-head bolt, 1/4" UNF thread, 7/8" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socket...

Hazard Flasher Relay - the switching relay in the hazard warning circuit. When the hazard switch is operated, the flasher relay pulses all four di...

Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...