Range Rover Classic Parts

Split Pin locks slotted nuts, clevis pins and linkage joints against loosening, passing through a drilled hole and splayed to retain the assembly. ...

Thermostat for the 2.5L 300TDi diesel engine, operating within the thermostat housing at the top of the cooling circuit. The thermostat regulates ...

Blanking Plug for closing a 1-5/8" hole in bodywork or panels. Seals an unused aperture or grommet hole in body panels, brackets and pedal/electri...

Plain Washer - metric M8 plain washer for use in general fastening assemblies throughout the vehicle. A standard flat washer used to distribute lo...

Front Screen Timer Relay is the grey timer relay within the heated front windscreen circuit. When the heated screen is switched on, this relay ene...

Early Seat Diaphragm Door Only - Discovery 1 4

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Bolt - a hexagonal-head bolt with an M6 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the vehicl...

Flat plain washer used within general fastening applications across multiple vehicle assemblies, providing a load distribution surface between the ...

Steering Wheel is a 15-inch three-spoke replacement wheel that mounts to the steering column. It is supplied without a boss, so a separate fitting...

Coolant Pipe Adaptor for the engine cooling circuit. It threads into the thermostat housing / cylinder head coolant outlet to provide the connectio...

Crankshaft Pulley mounts on the front of the crankshaft on the 200TDi 2.5L turbo diesel engine and drives the auxiliary drive belts. This pulley i...

Hose Clip - 12-20mm worm-drive hose clip suitable for hoses with an outside diameter of 12 to 20mm. This stainless-steel screw-type clip tightens ...

Setscrew is a fully threaded hex-head fastener used as a general-purpose fixing across engine and cooling assemblies. Threaded 5/16" UNC with a 5/...

Brake Pad Set for the front axle disc brake assembly, for use with vented front discs. The pads locate within the front calipers and clamp against ...

Inlet Manifold Seal sealing the inlet manifold to the cylinder block valley on the V8 petrol engine. This formed seal closes the manifold valley j...

Clutch Master Cylinder Overhaul Kit

Cleaner Air Filter Element

Track Rod End Boot Ring - spring retaining ring for the track rod end of the steering linkage. It clamps the rubber dust boot onto the track rod en...

Cooling Fan for the engine cooling assembly. Driven from the front of the engine through the viscous fan coupling, the fan draws air through the r...

Banjo Bolt is a hollow union bolt used in the fuel system of the 200 Tdi and 300 Tdi engines. It secures a banjo hose fitting at the injection pum...

Coolant Hose for the V8 carburettor petrol engine cooling circuit. It carries engine coolant between components of the cooling system, moulded to s...

Filler Plug in blue anodised aluminium, replacing the standard cooling system filler and blanking plug at the thermostat housing. Seals against a ...

Rocker Shaft for the 300 TDi engine, mounted in the cylinder head valvetrain. Carries and locates the rocker arms above the valves, providing the ...

Clutch Hose for the 300 Tdi 2.5L turbo diesel, forming the flexible section of the clutch hydraulic actuation circuit. The hose links the rigid pi...

Towing Socket Plate for the trailer towing electrics. This mounting plate carries the trailer electrical socket at the rear of the vehicle, provid...

Rear Brake Caliper for the left-hand side of the rear axle, part of the hydraulic braking circuit. The caliper carries the hydraulic pistons that ...

Nyloc Nut is an M16 nylon-insert self-locking nut that secures the front radius arm at its mounting within the front suspension. The nylon insert g...

Panhard Rod Bush for the front suspension lateral location assembly. This rubber bush is pressed into the Panhard rod eye and provides the complia...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Tappet Slide for Land Rover 4-cylinder engines, covering the Series I, Series II, Series IIA, and Series III (2.0L Diesel and 2.25L Petrol and Dies...

Oil Feed Pipe - Turbo supplies pressurised engine oil to the turbocharger in the 300 Tdi lubrication circuit. It carries oil from the cylinder blo...

Bottom Gasket Set for the 3.9L V8 EFI petrol engine, covering the lower (bottom-end) section of the engine during an overhaul. The set provides th...

EGR Valve to Pipe Gasket for the diesel exhaust gas recirculation (EGR) system. The gasket seals the flanged joint between the EGR valve and the r...

Headlamp Surround Retaining Screw for the front headlamp assembly. It secures the headlamp surround to the lamp housing. The screw holds the surro...

Pipe and Hose Retaining Clip - Engine is a small-bore clip used to retain pipes and hoses at multiple points across the engine bay and fuel system ...

Heater Blower Motor & Fan assembly for the cabin heating and ventilation system. The motor drives the fan that draws air through the heater box...

Oil Filter for the VM 2.4L and 2.5L 4-cylinder turbo diesel engine in the Range Rover Classic. This filter is fitted in the engine lubrication cir...

Accelerator Cable - throttle cable for TDi diesel applications. It connects the accelerator pedal to the injection pump throttle lever, transmitti...

Wiper Switch - Column is the steering-column stalk switch that controls the windscreen wash/wipe function. Mounted on the steering column, it sele...

Tensioner Pulley for the air conditioning drive belt on the 2.5L 300TDi turbo diesel engine. It runs against the accessory drive belt and maintain...

Oil cooler O-ring V8 small

Hose Clip for radiator hose connections on 4-cylinder TDi diesel engines. This screw-type hose clip secures the upper and lower radiator hoses at ...

Piston

Gearbox Mounting - left-hand transmission rubber mounting for the 2.5L 300 TDi diesel. This rubber-to-metal mounting supports the gearbox on the l...

Rear Brake Caliper, right-hand side, for the rear braking circuit on models fitted with solid (non-vented) rear discs. The caliper clamps the brake...

Piston Ring Set for the 300TDi diesel engine, supplied in standard size. The set provides the compression and oil control rings for one piston. Fo...

Oil Cooler Hose forms part of the engine oil cooling circuit on the 200TDi. It runs between the oil cooler and the oil pump/filter housing, carryi...