Range Rover Classic Parts

Clutch Driven Plate for the V8 clutch assembly. It is carried on the gearbox input shaft between the flywheel and the clutch cover (pressure plate)...

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

M6 Stud for the gearbox main casing. This threaded stud secures the speedometer drive housing to the transmission main casing, providing the fixin...

Instrument Voltage Stabiliser for the Range Rover Classic instrument cluster assembly. This component regulates the voltage supply to the instrume...

O-Ring - Oil Pick-Up Pipe for the 2.5L 300TDi 4-cylinder turbo diesel engine. This O-ring seals the oil pick-up pipe connection at the oil pump or...

Joint Washer - LT77 Front Cover seals the mating face between the front cover and the main casing of the LT77 5-speed manual gearbox. The washer p...

Rocker Cover Breather Hose - Left-Hand for the crankcase ventilation system of the Rover 3.5L V8 twin-carburettor engine. This hose connects the l...

Layshaft Taper Roller Bearing supports the front of the layshaft in the manual gearbox. This is the grooved front bearing, sized 31.75 x 62.0 mm. ...

seal washer for block coolant drain plug. - All 4-cylinder engines upto 1998 (except VM diesel)

special bolt for rocker shaft 200 TDI three per engine. sold EACH! - 90/110/130 - Discovery - Range Rover Classic

Steering Box Oil Seal Oil seal for the input (worm) shaft of the manual, non-power (Gemmer) steering box, sealing around the shaft where it enters ...

Shaft coupling

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

Outer Shim - 1.65mm - Front Halfshaft / CV Joint This 1.65mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Push Rod - a valvetrain component in the overhead-valve layout of the Rover V8 engine. It sits between the camshaft-driven tappet and the rocker a...

Front Coil Spring, part of the front coil-sprung suspension. The spring fits between the chassis spring seat and the front axle, supporting vehicl...

Heater Bypass Coolant Valve for V8 petrol applications. This vacuum-operated valve is installed in the HVAC coolant circuit and controls the flow ...

Fuel Pump Adaptor for mounting the external fuel pump on petrol engines. It provides the interface between the external fuel pump and its mounting...

Windscreen Filler Strip closes and trims the gap between the windscreen glass and the body aperture, forming part of the windscreen sealing and fin...

Gasket kit carburettor Zenith Stromberg 175CD

Torsion Spring Sleeve for the lower tailgate. It fits over the tailgate torsion spring, forming a protective bearing sleeve at the pivot and preven...

Gearbox Side Cover Gasket for the LT95 4-speed V8 gearbox. This gasket seals the side cover to the gearbox casing, preventing oil leaks from the ge...

Thermostat Housing for the 2.5L 300TDi 4-cylinder turbo diesel engine. This housing secures the engine thermostat within the cooling circuit and f...

Rocker Shaft Clamp for the cylinder head valve train on the 300TDi 2.5L turbo diesel engine. Secures the rocker shaft to the cylinder head pedesta...

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Joint Washer is a sealing washer fitted at a bolted or threaded joint on the 4-cylinder diesel engine, forming a seal between the mating faces to p...

Absorber Shock

Gear Lever Damper for the LT95 four-speed gearbox gear-change mechanism. This damping washer fits at the base of the main gear lever, absorbing vi...

Non-Return Valve for the V8 petrol engine, fitted to the inlet manifold vacuum take-off. The valve allows air to be drawn one way from the vacuum ...

Cable Tie for securing wiring looms and cables in Land Rover applications.

Torx Countersunk Screw is a fixing used within the upper tailgate assembly. The countersunk head seats flush with the mounting surface, while the ...

Special Bolt for retaining the tappets in the cylinder block, part of the camshaft and tappet assembly. This is a specific-design fastener that se...

Brake Union Washer is a sealing washer for hydraulic brake line connections. It seals the joint at a brake pipe or flexible hose union, fitting be...

Oil Cooler Pipe - a rigid pipe in the automatic transmission's oil cooling circuit, carrying fluid between the gearbox and the transmission oil coo...

Oil Pump Relief Valve Spring - sets the pressure at which the oil pump's relief valve opens. It holds the relief valve plunger closed against the ...

Lens side repeater 300TDI white

Hex-Head Setscrew, M6 x 20 mm, metric thread, fully threaded to the head. A general-purpose fixing used to secure components at M6 mounting points.

Left-Hand Rear Bumper Bracket that secures the rear bumper assembly to the body structure on the Range Rover Classic. This bracket is for the left...

Filler and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...

Exhaust Mounting supports the rear section of the exhaust system, suspending it from the underbody. This rubber mounting locates the rear of the t...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Distributor O-Ring, the sealing ring for the ignition distributor on the 3.5L V8 petrol engine. The O-ring seals the distributor base where it loc...

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Power Steering Hose - the high-pressure feed line in the power steering hydraulic circuit. It carries pressurised fluid from the power steering pu...

Grommet - rubber sealing grommet, 3/4 inch overall diameter with 1/8 inch centre hole. Used to seal and protect wiring cables where they pass thro...

Banjo Bolt secures the breather pipe to an axle, gearbox or transfer case housing. The bolt is drilled through its shank and head so that, clamped...

Drain Plug - Coolant - Cylinder Block is the threaded plug that seals the coolant drain port in the cylinder block, providing a controlled drain po...

Trunnion