Range Rover Classic Parts

Coating Spray Gun, bottle-mount type, for applying protective coating. This Schutz-style gun screws directly onto the 750ml coating bottle, so no s...

Rear suspension bush kit covering the trailing arm and A-frame mounting points of the rear coil-sprung suspension. The trailing arms locate the re...

Rear Shock Absorber Mounting Brackets for the rear suspension damper installation, supplied as a pair. These brackets weld to the rear axle housin...

Piston Ring Set seals the piston within the cylinder bore as part of the engine's piston assembly, providing combustion sealing, oil control and he...

Small-End Connecting Rod Bush for the 2.5L 200 TDi diesel engine. The small-end bush is pressed into the little end of the connecting rod and carr...

Front Axle Panhard Rod Bush - Late Type, for replacement at the Panhard rod mounting point on the front axle assembly. The bush provides the compl...

Primary Pinion Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox (V8) casing. 2.10 mm thick, it controls p...

Serrated Washer, 7/16", used within the clutch master cylinder and pipe assembly. The serrated face bites into the mating surface as the fixing is...

GENUINE LR camshaft sprocket for Rover V8 engines

Fuel Pump is the in-tank high-pressure pump in the fuel delivery system, mounted inside a metal fuel tank. It draws petrol from the tank and deliv...

4-Pin Differential for the Land Rover-type axle. The differential takes drive from the propshaft through the crown wheel and pinion and splits it ...

Breather Hose is part of the crankcase ventilation system on the 3.5L V8 twin-carburettor petrol engine. It routes breather gases through the vent...

Engine Mount - Right Hand supports the engine at the right-hand mounting point and isolates engine vibration from the chassis. It locates between ...

Ignition Wiring Harness - the low-tension (LT) link lead within the V8 petrol ignition system. This harness carries the low-tension (primary) side...

Brake Light Switch, the stop lamp switch mounted at the brake pedal. When the brake pedal is depressed the switch closes the stop lamp circuit to ...

rear output shaft LT95 4-speed gearbox V8 - S3 109" Stage 1 V8 - 101" Forward Control - Range Rover Classic 4-speed V8 - Early 110" 4-speed V8

Rear View Mirror

Rear Door Floor Side Panel - Right Hand is a body repair panel for the floor and sill area beneath the right-hand rear door. It replaces the corro...

Oil Cooler for the V8 Petrol engine oil cooling system. Reduces engine oil temperature by routing oil through a dedicated cooler core, maintaining...

Fuse Box Cover is the protective lid that fits over the fuse box, shielding the fuses and their connections from dust, moisture and accidental cont...

Shim 1.65mm for Layshaft Speed - V8 4

Pedestal Rocker

Gearbox Crossmember is a detachable structural member that bolts across the chassis side rails beneath the transmission. It carries the rear gearb...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Differential Guard - a wrap-around steel guard that shields the front or rear differential housing from impact and debris during off-road use. Des...

First Speed Bush for the LT77 five-speed manual gearbox. This selective-fit bush supports the first-speed gear on the mainshaft, within the first, ...

Tailgate Lock Screw - Upper, an M5 x 20 countersunk screw for the upper tailgate lock mechanism. This countersunk screw secures the upper tailgate...

Piston ring set for the 3.5L Rover V8 petrol engine, supplied per piston. The rings seal the combustion chamber against the cylinder bore, transfe...

Brake Hose Kit - a set of flexible braided brake hoses for the hydraulic braking circuit, carrying fluid from the chassis-mounted hard lines to the...

Air Conditioning Pipe Kit

PTO Shaft - Centre - the centre shaft in the power take-off (PTO) drive train. The power take-off transmits rotational drive from the transfer gea...

Wading Kit for the drivetrain and engine breather system, extending the breather points of the axles, gearbox and engine to a higher level. Raisin...

Transfer Box Drive Sprocket for the Borg Warner transfer gearbox. The sprocket drives the transfer chain that transmits torque from the mainshaft t...

Carburettor Needle for the SU variable-venturi carburettor in the fuel system of the 3.5L V8 petrol engine, in twin-carburettor configuration. The...

Fuel Injector for the 3.5L V8 EFI petrol engine. Meters fuel into the intake port as part of the electronic fuel injection system. For non-catalys...

Drive Screw for use in Land Rover body, chassis, and hardware assembly. A No.14 × 1" drive screw, supplied individually.

O-Ring for the air conditioning refrigerant circuit, used at the pipe and hose unions through the system including the condenser and evaporator con...

Window Regulator for the front left-hand door, part of the door glass lifting mechanism. This is the manual (wind-up) type: the scissor-and-channe...

Expansion Tank Bracket secures the coolant expansion tank in the engine bay, mounting it within the cooling system.

Tensioner Pulley Bearing for the auxiliary drive belt system on air-conditioned vehicles. It is the bearing carried within the idler/tensioner pul...

Rear Coil Spring - part of the rear suspension, supporting the vehicle weight and setting ride height at the rear axle. Uprated to give a +50mm ra...

Intermediate Shaft Circlip Retaining circlip for the intermediate shaft in the LT230 transfer box. Locates on the intermediate shaft to retain the...

Blanking Plate for the inlet manifold of the 3.5L V8 twin-carburettor petrol engine. The plate closes off an unused port on the manifold to maintai...

Heater Hose - Outlet is a moulded coolant hose in the cabin heater circuit, routing engine coolant between the cooling system and the heater matrix...

Hex Bolt - M10 x 40mm is a metric hexagon head bolt used in the hardware and fixings range for Land Rover vehicles. Thread specification M10, leng...

Rear Mudflap Mounting Angle, the angled bracket that secures a rear mudflap to the underbody. It positions and supports the mudflap behind the rea...

Glow Plug Lead for the pre-heat (glow plug) circuit of the 200 TDi and 300 TDi diesel engines. It interconnects the glow plugs and carries the sup...