for Discounts / VAT
for Discounts & Correct VAT
Parts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible. Covers pre-facelift and post-facelift specifications. Stock is held in the Netherlands and dispatched across the EU. Use the filters to narrow by model year, category, or quality grade.
Exhaust Gas Recirculation Gasket seals the exhaust gas recirculation (EGR) connection on the left-hand side, maintaining a gas-tight joint within t...
View full detailsEnergy-Absorbing Foam Pad is fitted within the fuel filter assembly, cushioning the filter and absorbing vibration and impact energy. Supplied for...
View full detailsCrankshaft Gear forms part of the timing gear train, mounted on the crankshaft nose to drive the timing system and maintain synchronisation between...
View full detailsHeater Hose carries engine coolant to the heater matrix, within the heater coolant circuit. It routes hot coolant between the engine and the heate...
View full detailsBypass Tube carries engine coolant on the bypass path, within the thermostat and housing assembly of the cooling circuit. It routes coolant around...
View full detailsFiller Plug closes the lubricant aperture on the axle case, within the front and rear axle and differential assembly. It seals the oil fill and le...
View full detailsAir Hose routes air within the turbocharger intake system, forming part of the charge-air ducting. It carries air along the turbocharger air path,...
View full detailsIntake Manifold Gasket seals the joint between the intake manifold and the cylinder head, within the air intake assembly. It maintains an airtight...
View full detailsSealing Ring sealing a joint within the engine timing gear covers. This O-ring seals a connection at the timing cover assembly, maintaining oil-ti...
View full detailsCover Gasket for the upper timing chain cover. It seals the joint between the upper timing chain cover and the engine, maintaining an oil-tight se...
View full detailsValve Stem Seal for the cylinder head valvetrain. It seals around the valve stem where it passes through the valve guide, controlling oil entry in...
View full detailsTiming Chain Guide for the engine timing gear. It supports and locates the timing chain along its run, controlling the chain path and reducing vib...
View full detailsTiming Chain Guide for the engine timing gear. It supports and locates the timing chain along its run, controlling the chain path and reducing vib...
View full detailsTiming Chain Tensioner Arm for the engine timing gear. It bears against the timing chain and transmits the tensioner load to take up slack and mai...
View full detailsSpecial Bolt for the engine timing gear assembly. It secures a component within the timing gear drive. Fitted to 2.0-litre diesel Ingenium engines...
View full detailsIdler Pulley for the accessory drive belt system, 65 mm in diameter. It guides the accessory (auxiliary) drive belt across its run, maintaining be...
View full detailsExhaust Manifold Gasket sealing the exhaust manifold and turbocharger joint. The same gasket serves both the exhaust manifold and the turbocharger...
View full detailsBolt securing the fuel injector and high-pressure fuel pipe assembly on the engine fuel system. It clamps the injector and high-pressure pipe unio...
View full detailsWater Outlet Tube forming the coolant outlet connection at the cylinder head, part of the engine cooling circuit. It carries coolant from the cyli...
View full detailsO-Ring for the turbocharger of the 2.0L I4 diesel (AJ200) engine, sealing the upper turbocharger-to-pipe joint (14.3 x 2.4 mm). The O-ring seals t...
View full detailsOil Drain Plug for the engine oil pan (sump). Threaded into the base of the oil pan, it seals the oil drain point and is removed to drain the engi...
View full detailsCylinder Head Bolt with hex head, for the 2.0L I4 diesel (AJ200) engine. The bolt secures the cylinder head to the engine block, providing the cla...
View full detailsShock Absorber Boot for the suspension damper assembly. The boot sheaths the exposed damper piston rod, shielding it from grit, moisture and road ...
View full detailsTurbocharger Gasket for the exhaust turbocharger assembly on the 2.0L I4 diesel (AJ200) engine, sealing the turbocharger outlet to the exhaust fron...
View full detailsCoolant Degas Hose for the engine cooling system, forming part of the deaeration (degas) circuit. The hose carries coolant and entrained air betwe...
View full detailsWheel Centre Cap for the alloy road wheel. This cover fits to the hub centre of the alloy wheel, closing off the centre bore and completing the wh...
View full detailsScrew - M6 x 25mm threaded fastener used across the 2.0L Ingenium petrol engine assembly. Secures components at the timing gear, fuel injector, wa...
View full detailsCoolant Hose for the engine cooling system on the 2.0L 16V TiVCT turbocharged Petrol. This hose carries coolant within the cooling circuit, connec...
View full detailsIntake Manifold Gasket sealing the intake manifold to the cylinder head on the 2.0L TIVCT turbocharged petrol engine (Gen2). It maintains an airti...
View full detailsPollen Filter for the heater and ventilation assembly. This cabin air filter installs within the heater assembly, filtering the air drawn into the...
View full detailsTransmission Fluid is the specified fluid for the electronically controlled all-wheel-drive coupling (Haldex-type) used on transverse-engine models...
View full detailsCoolant Hose - Outlet routes engine coolant within the cooling circuit of the 2.0L 16V TIVCT turbocharged petrol (Si4) engine. It carries coolant ...
View full detailsMetal Name Plate is an exterior badge fitted to the bodywork. It mounts to the body panel as a model or trim identifier and forms part of the vehic...
View full detailsBrake Fluid for the hydraulic braking and clutch actuation system, supplied in a 1 litre container. A DOT 4 low-viscosity (ESL) fluid formulated f...
View full detailsPump Drive Coupling for the 2.0L 16V Ti-VCT turbocharged petrol engine. Mounted at the camshaft drive, it transmits rotational drive from the cams...
View full detailsConnecting Rod Bearing - big-end bearing shell between the connecting rod and the crankshaft journal. Provides the low-friction running surface th...
View full detailsPower Transfer Unit Seal is an oil seal for the Power Transfer Unit (PTU) on transverse all-wheel-drive models. The PTU takes drive from the trans...
View full detailsRear Differential Oil Seal Kit - a set of oil seals for the rear differential and rear drive unit. The kit supplies the seals needed when resealin...
View full detailsVacuum Pump Seal seals the joint between the vacuum pump and the engine. It prevents oil and vacuum leakage at the pump mounting face, maintaining...
View full detailsAnti-Roll Bar Bush locates the anti-roll bar (stabiliser bar) to its mounting clamp. The bush allows the bar to twist under suspension articulatio...
View full detailsFuel Pump Support Housing Seal for the high-pressure fuel pump on the 2.0L Si4 petrol engine. The seal fits between the fuel pump support housing ...
View full detailsRetaining Clip - a fastener for exterior body mouldings and side-step trim. Secures body moulding and side-step trim panels to the bodywork.
Turbocharger Oil Return Hose Gasket for the 2.0L Si4 TIVCT petrol turbo engine. It seals the joint at the turbocharger oil return (drain) hose, al...
View full detailsInsulator - Stabilizer Bar
Steering Column Seal seals the point where the steering column shaft passes through the bulkhead, preventing the ingress of water, dust and draught...
View full detailsAccessory Drive Idler Pulley in the front end accessory drive (FEAD) belt system of the 2.0L 16V turbocharged petrol engine. The idler pulley guid...
View full detailsBody Moulding Retainer Clip, a lantern-type fastener for the vehicle's exterior trim. The clip secures exterior body mouldings - such as the rocke...
View full detailsEngine Compartment Insulator is the front insulation panel for the engine bay, providing acoustic and thermal insulation. Mounted at the front of ...
View full detailsParts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible, this collection covers pre-facelift and post-facelift specifications. If you own the 2019-onward Evoque, see the L551 parts collection.
The Range Rover Evoque L538 is the first-generation Evoque, produced at Halewood, UK from July 2011 to 2019 under chassis code L538. Model years run from 2012 to 2019. The collection covers the 5-door and 3-door SUV variants (produced through to 2018) and the convertible (produced from 2016 to 2019).
The L538 rides on the D8 platform, also known as LR-MS, a high-strength steel monocoque architecture developed by Land Rover as a heavily modified derivative of the Ford EUCD base. The D8 platform is also used on the Land Rover Discovery Sport. This architecture gives the Evoque a car-like driving character distinct from the body-on-frame and aluminium-intensive platforms used in other Range Rover generations.
Drivetrain configuration varies by variant. Four-wheel drive vehicles use a Haldex-based on-demand AWD system. Front-wheel drive was available on select diesel variants, specifically the eD4, which used a single-clutch, front-axle-only setup for improved efficiency. Confirming your drivetrain before ordering driveline, coupling, or differential components is essential. Generation-specific Haldex AWD service information is published by Haldex.
This collection does not cover the Range Rover Evoque L551 (2019 onward). If your vehicle was registered from 2019 onward, use the L551 parts collection linked in the intro above this product grid.
The L538 production run splits into two distinct specifications at the 2015 model year.
Pre-facelift vehicles (model years 2012 to 2015) used Ford-derived powerplants. Petrol variants used the 2.0L Ford EcoBoost Si4 turbo four-cylinder. Diesel variants used the 2.2L Ford Duratorq (PSA DW12) in TD4 and SD4 states of tune. The automatic gearbox on pre-facelift vehicles is the 6-speed Ford Aisin AW F-21 unit, also designated the Aisin Warner TF-81SC.
Post-facelift vehicles (model years 2016 to 2019) introduced JLR's Ingenium engine family. Both petrol and diesel variants moved to the 2.0L Ingenium turbo four-cylinder. The 9-speed ZF 9HP automatic gearbox replaced the 6-speed unit on automatic variants. The 6-speed Getrag M66EH50 manual remained available in select markets on diesel variants throughout the production run.
Engine-specific parts including oil filters, timing components, gaskets, sensors, and turbo components are not interchangeable between the Ford-derived and Ingenium specifications. Always confirm your engine code and model year before ordering.
Reference note: ZF 9HP transmission technical information is published by ZF Group.
Fitment GuidanceThe most reliable method for confirming parts fitment on an L538 is your Vehicle Identification Number (VIN). The VIN is a 17-character code stamped on the door jamb plate, on the windscreen base near the A-pillar (driver or passenger side depending on market variant), and recorded in your V5C or national registration document.
The tenth character of the VIN encodes the model year. The eighth character encodes the engine variant. If you are ordering engine-specific parts, turbo components, gearbox parts, or any item that changed at the 2015 facelift, cross-referencing your VIN with the part number is strongly recommended before purchase.
If you are unsure which specification your vehicle is, contact the Budget Parts team directly. Trade account holders can request fitment confirmation through the wholesale portal.
Catalogue ScopeThis collection includes suspension parts such as control arms, bushings, drop links, anti-roll bars, shock absorbers, and wheel bearings. Brake parts include pads, discs, calipers, brake pipes, and brake hardware. Engine parts cover oil filters, sump washers, hydraulic tappets, expansion tank caps, and ancillary components. Drivetrain parts include propshaft bolts, driveshaft components, and wheel nuts. The collection also includes electrical parts such as relays and sensors, service and maintenance items including ATF fluids and service hardware, body and chassis fixings, and workshop supplies including brake cleaner and fastener assortments.
Use the category filter above to narrow results to your area of work. The quality filter allows you to select between Genuine Land Rover, OEM, and Aftermarket grades.
Quality TiersEvery part in this collection is marked with one of three quality grades.
Genuine Land Rover parts are sourced through the official Jaguar Land Rover distribution channel. They carry the original Land Rover part number and packaging. These are the appropriate choice when OEM provenance documentation is required, such as for warranty or insurance purposes.
OEM parts are produced by the same manufacturers that supply Land Rover directly, sold outside the official JLR channel. The component is frequently identical to the Genuine part. OEM is the standard choice for independent workshops and experienced owners who want original-specification quality without the official channel markup.
Aftermarket parts are independently manufactured. Quality varies by supplier and application. Each listing specifies the grade, and the product description notes any relevant fitment or application limitations. Aftermarket is appropriate for non-critical components or where cost is the primary constraint.
TradeBudget Parts operates a wholesale portal for registered independent workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. If you manage a workshop or operate as a parts buyer, visit the wholesale login page to access trade terms or register your account.
Generation ReferenceThe L538 is the first-generation Evoque. The second-generation Evoque, the L551, entered production in 2019 on the PTA platform with 48V mild-hybrid technology and Ingenium engines throughout. Parts are not interchangeable between generations.
For the full Range Rover model family and generation reference, see the Range Rover parts collection.
Technical GuidesThe articles below provide diagnostic and technical context relevant to Range Rover Evoque L538 owners and workshops. They support, but do not duplicate, the parts categories in this collection.
Technical guide to the L538 covering the Ford-to-Ingenium engine split, Haldex service requirements, and the suspension and platform architecture that defined the first-generation Evoque.
Range Rover Evoque L538 guide →Owner and workshop guide to the Evoque convertible covering the structural changes for the open-roof configuration, the electric roof system, AWD configuration, and common faults relevant to parts selection.
Range Rover Evoque convertible guide →The Freelander 2 shares Haldex AWD architecture and overlapping engine families with the Evoque L538. This guide covers Haldex service intervals, coupling failure patterns, and rear differential diagnosis that applies directly to L538 AWD variants.
Freelander 2 faults and Haldex service guide →The Range Rover Evoque L538 was produced from July 2011 to 2019. Model years run from 2012 to 2019. The 5-door and 3-door SUV variants were produced through to 2018. The convertible variant was introduced in 2016 and produced through to 2019. Parts availability in this collection covers the full L538 production window across all body styles.
If your vehicle was registered before 2019, it is almost certainly the L538 first generation. If registered from 2019 onward, it is the L551 second generation. The clearest confirmation is your VIN. The tenth character of your 17-character VIN encodes the model year. You can also check the driver's door jamb plate, which will show the build date and in some markets the chassis code. If you are unsure, contact Budget Parts directly before ordering.
The L538 was significantly updated at the 2015 model year. Pre-facelift vehicles use Ford-derived engines (2.0L EcoBoost petrol, 2.2L Duratorq diesel) and a 6-speed Aisin automatic gearbox. Post-facelift vehicles use JLR Ingenium engines (2.0L petrol and diesel) and a 9-speed ZF 9HP automatic. Engine-specific parts including oil filters, timing components, turbo components, and gaskets are not interchangeable between these specifications. Always confirm your model year and engine code before ordering.
Four-wheel drive variants of the L538 use an on-demand Haldex AWD system. This couples the rear axle electronically and distributes torque when front-axle slip is detected. Some diesel variants were available in front-wheel drive only, specifically the eD4, which does not use a rear differential or Haldex coupling at all. Confirming your drivetrain configuration before ordering rear axle, coupling, or propshaft components is important. If you are unsure, check your V5C or contact Budget Parts.
The L538 used two engine families across its production run. Pre-facelift vehicles (2012 to 2015 model year) used the 2.0L Ford EcoBoost Si4 turbo petrol and the 2.2L Ford Duratorq (PSA DW12) diesel in TD4 and SD4 outputs. Post-facelift vehicles (2016 to 2019 model year) used JLR's 2.0L Ingenium turbo four-cylinder in both petrol and diesel forms. Parts that are engine-specific are listed with applicable engine codes in the product descriptions.
The L538 uses the D8 platform, also known as the LR-MS. This is a high-strength steel monocoque architecture developed by Land Rover as a substantially redesigned derivative of the Ford EUCD base. The same platform underpins the Land Rover Discovery Sport. It is a different architecture to the aluminium-intensive platforms used on the Range Rover L405 and Range Rover Sport L494.
Yes. Budget Parts operates a wholesale portal for registered workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. You can register or log in through the wholesale portal link in the site header. For volume orders or specific part enquiries, contact the Budget Parts team directly.
Updated: 13 May 2026