for Discounts / VAT
for Discounts & Correct VAT
Parts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible. Covers pre-facelift and post-facelift specifications. Stock is held in the Netherlands and dispatched across the EU. Use the filters to narrow by model year, category, or quality grade.
Fuel Filter for the diesel fuel supply system of the 2.2L DW12 common-rail direct-injection turbo diesel engine. It is fitted in the fuel line betw...
View full detailsWasher Fluid Level Sensor for the windscreen washer system. The sensor fits into the washer fluid reservoir and monitors the volume of fluid remai...
View full detailsCatalyst Gasket for the exhaust system of the 2.0L 16V Ti-VCT four-cylinder petrol engine. This gasket seals the joint at the catalytic converter ...
View full detailsBolt for the adjustable rear suspension arm on the Freelander 2 and Range Rover Evoque. This M14 × 85mm special bolt secures the adjustable rear a...
View full detailsCoolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...
View full detailsOil Filter is the replaceable element in the engine lubrication circuit, capturing wear particles and combustion contaminants from the oil before i...
View full detailsUpper Radiator Hose for the engine cooling circuit on the 2.0L Ti VCT petrol engine. This upper radiator hose carries engine coolant from the engi...
View full detailsHex Nut is an M6 flange nut with a 10mm hexagonal drive. It retains wheel arch liner and splashguard panels on their mounting studs. The integral ...
View full detailsIridium Spark Plug for the 2.0L 16V TIVCT turbocharged petrol engine (Si4, 240PS). The plug threads into the cylinder head and fires beneath its c...
View full detailsOil Filter for the engine lubrication system. Filters contaminants from the engine oil, protecting the lubrication circuit. Fitted to the 2.0L 16V...
View full detailsFront Crankshaft Oil Seal for the 2.0L TiVCT turbocharged petrol engine, located at the timing gear cover. Seals the front of the crankshaft where...
View full detailsPinion Bearing Spacer sits within the rear axle differential, setting the spacing and preload of the pinion bearings on the drive pinion. It maint...
View full detailsCrankshaft Gear forms part of the timing gear train, mounted on the crankshaft nose to drive the timing system and maintain synchronisation between...
View full detailsShock Absorber Boot for the suspension damper assembly. The boot sheaths the exposed damper piston rod, shielding it from grit, moisture and road ...
View full detailsScrew - M6 x 25mm threaded fastener used across the 2.0L Ingenium petrol engine assembly. Secures components at the timing gear, fuel injector, wa...
View full detailsCoolant Hose for the engine cooling system on the 2.0L 16V TiVCT turbocharged Petrol. This hose carries coolant within the cooling circuit, connec...
View full detailsPollen Filter for the heater and ventilation assembly. This cabin air filter installs within the heater assembly, filtering the air drawn into the...
View full detailsTransmission Fluid is the specified fluid for the electronically controlled all-wheel-drive coupling (Haldex-type) used on transverse-engine models...
View full detailsCoolant Hose - Outlet routes engine coolant within the cooling circuit of the 2.0L 16V TIVCT turbocharged petrol (Si4) engine. It carries coolant ...
View full detailsBrake Fluid for the hydraulic braking and clutch actuation system, supplied in a 1 litre container. A DOT 4 low-viscosity (ESL) fluid formulated f...
View full detailsPump Drive Coupling for the 2.0L 16V Ti-VCT turbocharged petrol engine. Mounted at the camshaft drive, it transmits rotational drive from the cams...
View full detailsConnecting Rod Bearing - big-end bearing shell between the connecting rod and the crankshaft journal. Provides the low-friction running surface th...
View full detailsVacuum Pump Seal seals the joint between the vacuum pump and the engine. It prevents oil and vacuum leakage at the pump mounting face, maintaining...
View full detailsAnti-Roll Bar Bush locates the anti-roll bar (stabiliser bar) to its mounting clamp. The bush allows the bar to twist under suspension articulatio...
View full detailsFuel Pump Support Housing Seal for the high-pressure fuel pump on the 2.0L Si4 petrol engine. The seal fits between the fuel pump support housing ...
View full detailsSwitch - Stop Light
Speed Control Inhibitor Switch - a pedal-actuated switch in the cruise (speed) control circuit. Mounted at the pedal box, it signals the control m...
View full detailsTurbocharger Oil Return Hose Gasket for the 2.0L Si4 TIVCT petrol turbo engine. It seals the joint at the turbocharger oil return (drain) hose, al...
View full detailsInsulator - Stabilizer Bar
Steering Column Seal seals the point where the steering column shaft passes through the bulkhead, preventing the ingress of water, dust and draught...
View full detailsTurbocharger Washer is a fitting washer used at the turbocharger on the 2.0L 16V TIVCT petrol turbo engine (240PS).
Exhaust Manifold Gasket seals the joint between the turbocharger and the exhaust manifold, containing exhaust gas at the flanged connection. Fitte...
View full detailsExhaust Manifold Gasket seals the joint between the turbocharger/exhaust manifold and the cylinder head, containing exhaust gas at the port face. ...
View full detailsValve Cover Gasket seals the joint between the camshaft cover and the cylinder head on the 2.0L 16V turbocharged petrol engine. It forms the oil-t...
View full detailsTurbocharger Water Inlet Gasket seals the coolant inlet connection at the turbocharger. It fits between the coolant feed union and the turbocharger...
View full detailsTurbocharger Oil Feed Filter is a small in-line filter located in the turbocharger oil feed pipe. It traps particulate debris carried in the pressu...
View full detailsManifold to Cylinder Head Stud secures the exhaust manifold and turbocharger assembly to the cylinder head. Threaded mounting stud used in the exh...
View full detailsCamshaft Sprocket Washer for the 2.0L 16V TiVCT turbocharged petrol engine (Si4 240PS and Gen2). It fits at the camshaft sprocket within the timing...
View full detailsExhaust Pipe Gasket for the front exhaust section of the 2.0L turbocharged petrol engine. Seals the flanged front pipe to catalyst joint, providin...
View full detailsOil Drain Plug for the 2.0L 16V petrol engine. It seals the drain point in the oil pan (sump) and is removed to drain the engine oil at a service.
Timing Gear Bolt for the 2.0L 16V petrol engine. It secures a gear on the engine's timing drive.
Valve Spring Retainer for the 2.0L 16-valve turbocharged petrol engine, fitted in the cylinder head valve train. The retainer caps the top of the ...
View full detailsCrankshaft Damper Washer for the 2.0L 16-valve turbocharged petrol engine, fitted in the crankshaft damper assembly at the front of the timing gear...
View full detailsOil Filter Adaptor Gasket for the 2.0L 16-valve turbocharged petrol engine, sealing the oil cooler and filter adaptor to the engine. The gasket fo...
View full detailsAccessory Drive Pulley Bolt for the 2.0L 16-valve turbocharged petrol engine, used in the accessory drive belt system. The bolt secures the access...
View full detailsBolt securing the front suspension lower control arm at its rear fixing point. M14 x 90mm, Torx drive head.
High Pressure Fuel Pump Tappet drives the engine-mounted high-pressure fuel pump from the camshaft. The tappet acts as the cam follower, riding on...
View full detailsVacuum Hose for the exhaust gas recirculation (EGR) system on the 2.2L diesel engine. Connects the control valve to the EGR cooler.
Parts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible, this collection covers pre-facelift and post-facelift specifications. If you own the 2019-onward Evoque, see the L551 parts collection.
The Range Rover Evoque L538 is the first-generation Evoque, produced at Halewood, UK from July 2011 to 2019 under chassis code L538. Model years run from 2012 to 2019. The collection covers the 5-door and 3-door SUV variants (produced through to 2018) and the convertible (produced from 2016 to 2019).
The L538 rides on the D8 platform, also known as LR-MS, a high-strength steel monocoque architecture developed by Land Rover as a heavily modified derivative of the Ford EUCD base. The D8 platform is also used on the Land Rover Discovery Sport. This architecture gives the Evoque a car-like driving character distinct from the body-on-frame and aluminium-intensive platforms used in other Range Rover generations.
Drivetrain configuration varies by variant. Four-wheel drive vehicles use a Haldex-based on-demand AWD system. Front-wheel drive was available on select diesel variants, specifically the eD4, which used a single-clutch, front-axle-only setup for improved efficiency. Confirming your drivetrain before ordering driveline, coupling, or differential components is essential. Generation-specific Haldex AWD service information is published by Haldex.
This collection does not cover the Range Rover Evoque L551 (2019 onward). If your vehicle was registered from 2019 onward, use the L551 parts collection linked in the intro above this product grid.
The L538 production run splits into two distinct specifications at the 2015 model year.
Pre-facelift vehicles (model years 2012 to 2015) used Ford-derived powerplants. Petrol variants used the 2.0L Ford EcoBoost Si4 turbo four-cylinder. Diesel variants used the 2.2L Ford Duratorq (PSA DW12) in TD4 and SD4 states of tune. The automatic gearbox on pre-facelift vehicles is the 6-speed Ford Aisin AW F-21 unit, also designated the Aisin Warner TF-81SC.
Post-facelift vehicles (model years 2016 to 2019) introduced JLR's Ingenium engine family. Both petrol and diesel variants moved to the 2.0L Ingenium turbo four-cylinder. The 9-speed ZF 9HP automatic gearbox replaced the 6-speed unit on automatic variants. The 6-speed Getrag M66EH50 manual remained available in select markets on diesel variants throughout the production run.
Engine-specific parts including oil filters, timing components, gaskets, sensors, and turbo components are not interchangeable between the Ford-derived and Ingenium specifications. Always confirm your engine code and model year before ordering.
Reference note: ZF 9HP transmission technical information is published by ZF Group.
Fitment GuidanceThe most reliable method for confirming parts fitment on an L538 is your Vehicle Identification Number (VIN). The VIN is a 17-character code stamped on the door jamb plate, on the windscreen base near the A-pillar (driver or passenger side depending on market variant), and recorded in your V5C or national registration document.
The tenth character of the VIN encodes the model year. The eighth character encodes the engine variant. If you are ordering engine-specific parts, turbo components, gearbox parts, or any item that changed at the 2015 facelift, cross-referencing your VIN with the part number is strongly recommended before purchase.
If you are unsure which specification your vehicle is, contact the Budget Parts team directly. Trade account holders can request fitment confirmation through the wholesale portal.
Catalogue ScopeThis collection includes suspension parts such as control arms, bushings, drop links, anti-roll bars, shock absorbers, and wheel bearings. Brake parts include pads, discs, calipers, brake pipes, and brake hardware. Engine parts cover oil filters, sump washers, hydraulic tappets, expansion tank caps, and ancillary components. Drivetrain parts include propshaft bolts, driveshaft components, and wheel nuts. The collection also includes electrical parts such as relays and sensors, service and maintenance items including ATF fluids and service hardware, body and chassis fixings, and workshop supplies including brake cleaner and fastener assortments.
Use the category filter above to narrow results to your area of work. The quality filter allows you to select between Genuine Land Rover, OEM, and Aftermarket grades.
Quality TiersEvery part in this collection is marked with one of three quality grades.
Genuine Land Rover parts are sourced through the official Jaguar Land Rover distribution channel. They carry the original Land Rover part number and packaging. These are the appropriate choice when OEM provenance documentation is required, such as for warranty or insurance purposes.
OEM parts are produced by the same manufacturers that supply Land Rover directly, sold outside the official JLR channel. The component is frequently identical to the Genuine part. OEM is the standard choice for independent workshops and experienced owners who want original-specification quality without the official channel markup.
Aftermarket parts are independently manufactured. Quality varies by supplier and application. Each listing specifies the grade, and the product description notes any relevant fitment or application limitations. Aftermarket is appropriate for non-critical components or where cost is the primary constraint.
TradeBudget Parts operates a wholesale portal for registered independent workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. If you manage a workshop or operate as a parts buyer, visit the wholesale login page to access trade terms or register your account.
Generation ReferenceThe L538 is the first-generation Evoque. The second-generation Evoque, the L551, entered production in 2019 on the PTA platform with 48V mild-hybrid technology and Ingenium engines throughout. Parts are not interchangeable between generations.
For the full Range Rover model family and generation reference, see the Range Rover parts collection.
Technical GuidesThe articles below provide diagnostic and technical context relevant to Range Rover Evoque L538 owners and workshops. They support, but do not duplicate, the parts categories in this collection.
Technical guide to the L538 covering the Ford-to-Ingenium engine split, Haldex service requirements, and the suspension and platform architecture that defined the first-generation Evoque.
Range Rover Evoque L538 guide →Owner and workshop guide to the Evoque convertible covering the structural changes for the open-roof configuration, the electric roof system, AWD configuration, and common faults relevant to parts selection.
Range Rover Evoque convertible guide →The Freelander 2 shares Haldex AWD architecture and overlapping engine families with the Evoque L538. This guide covers Haldex service intervals, coupling failure patterns, and rear differential diagnosis that applies directly to L538 AWD variants.
Freelander 2 faults and Haldex service guide →The Range Rover Evoque L538 was produced from July 2011 to 2019. Model years run from 2012 to 2019. The 5-door and 3-door SUV variants were produced through to 2018. The convertible variant was introduced in 2016 and produced through to 2019. Parts availability in this collection covers the full L538 production window across all body styles.
If your vehicle was registered before 2019, it is almost certainly the L538 first generation. If registered from 2019 onward, it is the L551 second generation. The clearest confirmation is your VIN. The tenth character of your 17-character VIN encodes the model year. You can also check the driver's door jamb plate, which will show the build date and in some markets the chassis code. If you are unsure, contact Budget Parts directly before ordering.
The L538 was significantly updated at the 2015 model year. Pre-facelift vehicles use Ford-derived engines (2.0L EcoBoost petrol, 2.2L Duratorq diesel) and a 6-speed Aisin automatic gearbox. Post-facelift vehicles use JLR Ingenium engines (2.0L petrol and diesel) and a 9-speed ZF 9HP automatic. Engine-specific parts including oil filters, timing components, turbo components, and gaskets are not interchangeable between these specifications. Always confirm your model year and engine code before ordering.
Four-wheel drive variants of the L538 use an on-demand Haldex AWD system. This couples the rear axle electronically and distributes torque when front-axle slip is detected. Some diesel variants were available in front-wheel drive only, specifically the eD4, which does not use a rear differential or Haldex coupling at all. Confirming your drivetrain configuration before ordering rear axle, coupling, or propshaft components is important. If you are unsure, check your V5C or contact Budget Parts.
The L538 used two engine families across its production run. Pre-facelift vehicles (2012 to 2015 model year) used the 2.0L Ford EcoBoost Si4 turbo petrol and the 2.2L Ford Duratorq (PSA DW12) diesel in TD4 and SD4 outputs. Post-facelift vehicles (2016 to 2019 model year) used JLR's 2.0L Ingenium turbo four-cylinder in both petrol and diesel forms. Parts that are engine-specific are listed with applicable engine codes in the product descriptions.
The L538 uses the D8 platform, also known as the LR-MS. This is a high-strength steel monocoque architecture developed by Land Rover as a substantially redesigned derivative of the Ford EUCD base. The same platform underpins the Land Rover Discovery Sport. It is a different architecture to the aluminium-intensive platforms used on the Range Rover L405 and Range Rover Sport L494.
Yes. Budget Parts operates a wholesale portal for registered workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. You can register or log in through the wholesale portal link in the site header. For volume orders or specific part enquiries, contact the Budget Parts team directly.
Updated: 13 May 2026