for Discounts / VAT
for Discounts & Correct VAT
Parts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible. Covers pre-facelift and post-facelift specifications. Stock is held in the Netherlands and dispatched across the EU. Use the filters to narrow by model year, category, or quality grade.
Turbocharger Washer is a fitting washer used at the turbocharger on the 2.0L 16V TIVCT petrol turbo engine (240PS).
Windscreen Washer Pump Grommet seals the washer pump into the windscreen washer fluid reservoir. This rubber grommet fits into the reservoir body ...
View full detailsFuel Pump O-Ring Seal, 31mm x 2mm - the sealing ring at the fuel pump / fuel injection pump joint. This O-ring is the only seal at that joint, so ...
View full detailsAutomatic Transmission Fluid (ATF) for the automatic gearbox and power steering circuit. Specified as the transmission and power steering fluid to...
View full detailsTrim Clip - a plastic push-fit retaining clip used to secure exterior trim and body mouldings to the vehicle. It locates in a pre-drilled panel hol...
View full detailsPlastic Rivet is a push-fit fastener that secures front engine-compartment insulation panels to the body. It locates into a pre-formed panel hole t...
View full detailsWater Bypass Hose from the thermostat housing group of the engine cooling circuit, fitted to the 2.0L Ingenium four-cylinder petrol engine (AJ200 a...
View full detailsExhaust Manifold Gasket seals the joint between the turbocharger and the exhaust manifold, containing exhaust gas at the flanged connection. Fitte...
View full detailsExhaust Manifold Gasket seals the joint between the turbocharger/exhaust manifold and the cylinder head, containing exhaust gas at the port face. ...
View full detailsValve Cover Gasket seals the joint between the camshaft cover and the cylinder head on the 2.0L 16V turbocharged petrol engine. It forms the oil-t...
View full detailsOil - Differential
Turbocharger Water Inlet Gasket seals the coolant inlet connection at the turbocharger. It fits between the coolant feed union and the turbocharger...
View full detailsTurbocharger Oil Feed Filter is a small in-line filter located in the turbocharger oil feed pipe. It traps particulate debris carried in the pressu...
View full detailsManifold to Cylinder Head Stud secures the exhaust manifold and turbocharger assembly to the cylinder head. Threaded mounting stud used in the exh...
View full detailsCamshaft Sprocket Washer for the 2.0L 16V TiVCT turbocharged petrol engine (Si4 240PS and Gen2). It fits at the camshaft sprocket within the timing...
View full detailsExhaust Pipe Gasket for the front exhaust section of the 2.0L turbocharged petrol engine. Seals the flanged front pipe to catalyst joint, providin...
View full detailsOil Drain Plug for the 2.0L 16V petrol engine. It seals the drain point in the oil pan (sump) and is removed to drain the engine oil at a service.
Timing Gear Bolt for the 2.0L 16V petrol engine. It secures a gear on the engine's timing drive.
Valve Spring Retainer for the 2.0L 16-valve turbocharged petrol engine, fitted in the cylinder head valve train. The retainer caps the top of the ...
View full detailsCrankshaft Damper Washer for the 2.0L 16-valve turbocharged petrol engine, fitted in the crankshaft damper assembly at the front of the timing gear...
View full detailsDrive Chain Idler - timing gear idler sprocket for the 2.0L four-cylinder Ingenium engine family (AJ200 / AJ20 series, petrol and diesel). The idl...
View full detailsOil Filter Adaptor Gasket for the 2.0L 16-valve turbocharged petrol engine, sealing the oil cooler and filter adaptor to the engine. The gasket fo...
View full detailsAccessory Drive Pulley Bolt for the 2.0L 16-valve turbocharged petrol engine, used in the accessory drive belt system. The bolt secures the access...
View full detailsTurbocharger Oil Return Hose returns lubricating oil from the turbocharger to the engine on the 2.0L 16V turbocharged petrol engine. Connected to ...
View full detailsWindscreen Washer Reservoir stores the washer fluid supply for the screen wash system and, on this variant, the headlamp power wash jets. This res...
View full detailsEngine Mounting Bolt with hexagonal head, M12 x 112 mm. A structural fastener securing the engine mounting to the subframe; the same bolt is also ...
View full detailsUpper Knuckle Bolt is a hex-head bolt that retains the upper knuckle joint within the hub and knuckle assembly. It clamps the upper knuckle to the...
View full detailsBolt securing the front suspension lower control arm at its rear fixing point. M14 x 90mm, Torx drive head.
High Pressure Fuel Pump Tappet drives the engine-mounted high-pressure fuel pump from the camshaft. The tappet acts as the cam follower, riding on...
View full detailsFront Brake Hose - flexible hydraulic hose in the front brake circuit, left-hand side. It carries brake fluid from the rigid pipe on the body to t...
View full detailsFront Brake Hose - flexible hydraulic hose in the front brake circuit, right-hand side. It carries brake fluid from the rigid pipe on the body to ...
View full detailsDiesel Exhaust Fluid (AdBlue) for diesel vehicles fitted with a selective catalytic reduction (SCR) exhaust after-treatment system. The fluid is h...
View full detailsVacuum Hose for the exhaust gas recirculation (EGR) system on the 2.2L diesel engine. Connects the control valve to the EGR cooler.
EGR Cooler Gasket for the 2.2L diesel engine, part of the exhaust gas recirculation (EGR) system. Seals the joint between the exhaust manifold and...
View full detailsExhaust Manifold Gasket for the 2.2L CR DI 16V (Td4) turbo diesel engine. It seals the joint between the exhaust manifold and the cylinder head, co...
View full detailsCover - Mirror Housing
Coolant Overflow Hose for the engine cooling system, running between the coolant expansion (degas) tank and the cooling circuit. As the engine war...
View full detailsCoolant Hose forms part of the engine cooling circuit, carrying coolant between the cooling-system components. Moulded to suit the 2.0L 16V turboc...
View full detailsAxle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...
View full detailsBreather Valve for the axle case or manual transmission housing. The valve vents the housing to atmosphere, allowing internal air pressure to equa...
View full detailsAccessory Drive Idler Pulley - Lower in the front end accessory drive (FEAD) belt system of the 2.0L 16V turbocharged petrol engine. The lower idl...
View full detailsHeater Hose for the engine cooling and cabin heating circuit. This hose carries heated engine coolant between the engine and the heater matrix, wh...
View full detailsBrake Disc Retaining Screw that locates the brake disc against the wheel hub flange, holding the disc square and in position while the caliper and ...
View full detailsBattery Management System sensor for the negative battery terminal, forming part of the vehicle's battery monitoring and charge-control circuit. I...
View full detailsRetaining Clip is a fastening clip used in the radiator grille and front bumper assembly. It secures the grille and front bumper trim components t...
View full detailsClip - retaining clip for the radiator grille and front bumper assembly. It secures the grille and bumper components to their mountings.
Torque Converter Oil Seal seals the front of the ZF 9HP nine-speed automatic transmission where the torque converter hub enters the pump housing. I...
View full detailsEGR Cooler Hose, part of the Exhaust Gas Recirculation (EGR) system on the 2.2L CR DI 16V diesel engine. It connects to the EGR cooler, which lowe...
View full detailsParts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible, this collection covers pre-facelift and post-facelift specifications. If you own the 2019-onward Evoque, see the L551 parts collection.
The Range Rover Evoque L538 is the first-generation Evoque, produced at Halewood, UK from July 2011 to 2019 under chassis code L538. Model years run from 2012 to 2019. The collection covers the 5-door and 3-door SUV variants (produced through to 2018) and the convertible (produced from 2016 to 2019).
The L538 rides on the D8 platform, also known as LR-MS, a high-strength steel monocoque architecture developed by Land Rover as a heavily modified derivative of the Ford EUCD base. The D8 platform is also used on the Land Rover Discovery Sport. This architecture gives the Evoque a car-like driving character distinct from the body-on-frame and aluminium-intensive platforms used in other Range Rover generations.
Drivetrain configuration varies by variant. Four-wheel drive vehicles use a Haldex-based on-demand AWD system. Front-wheel drive was available on select diesel variants, specifically the eD4, which used a single-clutch, front-axle-only setup for improved efficiency. Confirming your drivetrain before ordering driveline, coupling, or differential components is essential. Generation-specific Haldex AWD service information is published by Haldex.
This collection does not cover the Range Rover Evoque L551 (2019 onward). If your vehicle was registered from 2019 onward, use the L551 parts collection linked in the intro above this product grid.
The L538 production run splits into two distinct specifications at the 2015 model year.
Pre-facelift vehicles (model years 2012 to 2015) used Ford-derived powerplants. Petrol variants used the 2.0L Ford EcoBoost Si4 turbo four-cylinder. Diesel variants used the 2.2L Ford Duratorq (PSA DW12) in TD4 and SD4 states of tune. The automatic gearbox on pre-facelift vehicles is the 6-speed Ford Aisin AW F-21 unit, also designated the Aisin Warner TF-81SC.
Post-facelift vehicles (model years 2016 to 2019) introduced JLR's Ingenium engine family. Both petrol and diesel variants moved to the 2.0L Ingenium turbo four-cylinder. The 9-speed ZF 9HP automatic gearbox replaced the 6-speed unit on automatic variants. The 6-speed Getrag M66EH50 manual remained available in select markets on diesel variants throughout the production run.
Engine-specific parts including oil filters, timing components, gaskets, sensors, and turbo components are not interchangeable between the Ford-derived and Ingenium specifications. Always confirm your engine code and model year before ordering.
Reference note: ZF 9HP transmission technical information is published by ZF Group.
Fitment GuidanceThe most reliable method for confirming parts fitment on an L538 is your Vehicle Identification Number (VIN). The VIN is a 17-character code stamped on the door jamb plate, on the windscreen base near the A-pillar (driver or passenger side depending on market variant), and recorded in your V5C or national registration document.
The tenth character of the VIN encodes the model year. The eighth character encodes the engine variant. If you are ordering engine-specific parts, turbo components, gearbox parts, or any item that changed at the 2015 facelift, cross-referencing your VIN with the part number is strongly recommended before purchase.
If you are unsure which specification your vehicle is, contact the Budget Parts team directly. Trade account holders can request fitment confirmation through the wholesale portal.
Catalogue ScopeThis collection includes suspension parts such as control arms, bushings, drop links, anti-roll bars, shock absorbers, and wheel bearings. Brake parts include pads, discs, calipers, brake pipes, and brake hardware. Engine parts cover oil filters, sump washers, hydraulic tappets, expansion tank caps, and ancillary components. Drivetrain parts include propshaft bolts, driveshaft components, and wheel nuts. The collection also includes electrical parts such as relays and sensors, service and maintenance items including ATF fluids and service hardware, body and chassis fixings, and workshop supplies including brake cleaner and fastener assortments.
Use the category filter above to narrow results to your area of work. The quality filter allows you to select between Genuine Land Rover, OEM, and Aftermarket grades.
Quality TiersEvery part in this collection is marked with one of three quality grades.
Genuine Land Rover parts are sourced through the official Jaguar Land Rover distribution channel. They carry the original Land Rover part number and packaging. These are the appropriate choice when OEM provenance documentation is required, such as for warranty or insurance purposes.
OEM parts are produced by the same manufacturers that supply Land Rover directly, sold outside the official JLR channel. The component is frequently identical to the Genuine part. OEM is the standard choice for independent workshops and experienced owners who want original-specification quality without the official channel markup.
Aftermarket parts are independently manufactured. Quality varies by supplier and application. Each listing specifies the grade, and the product description notes any relevant fitment or application limitations. Aftermarket is appropriate for non-critical components or where cost is the primary constraint.
TradeBudget Parts operates a wholesale portal for registered independent workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. If you manage a workshop or operate as a parts buyer, visit the wholesale login page to access trade terms or register your account.
Generation ReferenceThe L538 is the first-generation Evoque. The second-generation Evoque, the L551, entered production in 2019 on the PTA platform with 48V mild-hybrid technology and Ingenium engines throughout. Parts are not interchangeable between generations.
For the full Range Rover model family and generation reference, see the Range Rover parts collection.
Technical GuidesThe articles below provide diagnostic and technical context relevant to Range Rover Evoque L538 owners and workshops. They support, but do not duplicate, the parts categories in this collection.
Technical guide to the L538 covering the Ford-to-Ingenium engine split, Haldex service requirements, and the suspension and platform architecture that defined the first-generation Evoque.
Range Rover Evoque L538 guide →Owner and workshop guide to the Evoque convertible covering the structural changes for the open-roof configuration, the electric roof system, AWD configuration, and common faults relevant to parts selection.
Range Rover Evoque convertible guide →The Freelander 2 shares Haldex AWD architecture and overlapping engine families with the Evoque L538. This guide covers Haldex service intervals, coupling failure patterns, and rear differential diagnosis that applies directly to L538 AWD variants.
Freelander 2 faults and Haldex service guide →The Range Rover Evoque L538 was produced from July 2011 to 2019. Model years run from 2012 to 2019. The 5-door and 3-door SUV variants were produced through to 2018. The convertible variant was introduced in 2016 and produced through to 2019. Parts availability in this collection covers the full L538 production window across all body styles.
If your vehicle was registered before 2019, it is almost certainly the L538 first generation. If registered from 2019 onward, it is the L551 second generation. The clearest confirmation is your VIN. The tenth character of your 17-character VIN encodes the model year. You can also check the driver's door jamb plate, which will show the build date and in some markets the chassis code. If you are unsure, contact Budget Parts directly before ordering.
The L538 was significantly updated at the 2015 model year. Pre-facelift vehicles use Ford-derived engines (2.0L EcoBoost petrol, 2.2L Duratorq diesel) and a 6-speed Aisin automatic gearbox. Post-facelift vehicles use JLR Ingenium engines (2.0L petrol and diesel) and a 9-speed ZF 9HP automatic. Engine-specific parts including oil filters, timing components, turbo components, and gaskets are not interchangeable between these specifications. Always confirm your model year and engine code before ordering.
Four-wheel drive variants of the L538 use an on-demand Haldex AWD system. This couples the rear axle electronically and distributes torque when front-axle slip is detected. Some diesel variants were available in front-wheel drive only, specifically the eD4, which does not use a rear differential or Haldex coupling at all. Confirming your drivetrain configuration before ordering rear axle, coupling, or propshaft components is important. If you are unsure, check your V5C or contact Budget Parts.
The L538 used two engine families across its production run. Pre-facelift vehicles (2012 to 2015 model year) used the 2.0L Ford EcoBoost Si4 turbo petrol and the 2.2L Ford Duratorq (PSA DW12) diesel in TD4 and SD4 outputs. Post-facelift vehicles (2016 to 2019 model year) used JLR's 2.0L Ingenium turbo four-cylinder in both petrol and diesel forms. Parts that are engine-specific are listed with applicable engine codes in the product descriptions.
The L538 uses the D8 platform, also known as the LR-MS. This is a high-strength steel monocoque architecture developed by Land Rover as a substantially redesigned derivative of the Ford EUCD base. The same platform underpins the Land Rover Discovery Sport. It is a different architecture to the aluminium-intensive platforms used on the Range Rover L405 and Range Rover Sport L494.
Yes. Budget Parts operates a wholesale portal for registered workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. You can register or log in through the wholesale portal link in the site header. For volume orders or specific part enquiries, contact the Budget Parts team directly.
Updated: 13 May 2026