for Discounts / VAT
for Discounts & Correct VAT
Parts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible. Covers pre-facelift and post-facelift specifications. Stock is held in the Netherlands and dispatched across the EU. Use the filters to narrow by model year, category, or quality grade.
Oil Seal - M66 Gearbox Driveshaft is the 67mm driveshaft oil seal for the M66 six-speed manual transmission. It seals the driveshaft output where ...
View full detailsSealing Ring - Input Shaft is an O-ring seal fitted to the input shaft of the M66 six-speed manual transmission. It seals the joint where the inpu...
View full detailsOil Seal - 30 x 40mm is an external oil seal for the M66 six-speed manual transmission. It seals a rotating shaft where it exits the gearbox casin...
View full detailsOil Separator is part of the crankcase emission control system, separating oil mist from crankcase gases before they are returned to the intake. F...
View full detailsAir Conditioning O-Ring, 13.7 x 2.5mm, for the R134a refrigerant circuit. It seals a line connection in the front air-conditioning system on the c...
View full detailsO-Ring - 9.5 x 2.5 mm seals a joint in the air conditioning refrigerant circuit, at the condenser and compressor connections. Compatible with syst...
View full detailsBolt and Washer is a hex-head bolt with washer for the cylinder block. Used at the cylinder block and its plugs on the 2.2L diesel engine.
Heater Matrix is the heat exchanger within the heater and air-conditioning unit. Engine coolant circulates through the matrix while cabin air is d...
View full detailsHeater Matrix is the heat exchanger within the heater and air-conditioning unit. Engine coolant circulates through the matrix while cabin air is d...
View full detailsFuel Feed Tube is a fuel supply line in the fuel delivery system. It carries fuel to the engine on the 2.0L 16V TiVCT turbocharged petrol engine, ...
View full detailsCamshaft is the inlet camshaft for the 2.0L 16V TiVCT turbocharged petrol engine. It operates the intake valves, running in the cylinder head and ...
View full detailsCamshaft is the inlet camshaft for the 2.0L 16V TiVCT turbocharged petrol engine. It operates the intake valves, running in the cylinder head and ...
View full detailsFuel Return Pipe (Injector Leak-Off) in the fuel injection return circuit of the 2.2L diesel engine. The pipe collects leak-off fuel from the inje...
View full detailsCamshaft Position Sensor monitors camshaft rotation for the engine management system. Mounted in the cylinder head and camshaft cover, it signals ...
View full detailsConnecting Rod Bearing Set in standard size for the Ingenium AJ200 / AJ204 2.0L diesel engine in its lower-output form (150 hp and 180 hp). The be...
View full detailsDrive Belt Tensioner Pulley for the auxiliary (accessory) drive belt. The pulley bears against the drive belt, maintaining correct tension as the ...
View full detailsDrive Belt Tensioner Pulley for the auxiliary (accessory) drive belt. The pulley bears against the drive belt, maintaining correct tension as the ...
View full detailsTiming Chain Tensioner - hydraulic tensioner in the timing chain drive of the 2.0L Ingenium four-cylinder turbo diesel (AJ200D / AJ20D4). The tens...
View full detailsWater Pump - Auxiliary is an electrically driven coolant pump that circulates coolant through the auxiliary and heater circuit, independently of th...
View full detailsValve Stem Seal - valve train sealing component in the cylinder head of the 2.2L Td4 diesel engine. The seal fits over the valve stem at the top o...
View full detailsPedal Switch - multi-function pedal-position switch used in the brake and clutch pedal controls on manual transmission vehicles. The switch is mou...
View full detailsClutch Master Cylinder - the hydraulic actuator at the head of the clutch circuit. Mounted on the pedal box, it converts clutch-pedal effort into h...
View full detailsFront Brake Disc - internally vented, 325mm diameter, supplied singly. The disc bolts to the front hub and forms the friction surface for the fron...
View full detailsUpper Engine Mounting - component of the powertrain mounting system, forming the upper support point between the engine and the body structure. Th...
View full detailsExhaust Differential Pressure Sensor - part of the diesel particulate filter monitoring circuit in the exhaust aftertreatment system. The sensor i...
View full detailsExhaust Differential Pressure Sensor - part of the diesel particulate filter monitoring circuit in the exhaust aftertreatment system. The sensor i...
View full detailsThermostat Housing - coolant outlet housing in the engine cooling circuit of the 2.2L Td4 diesel engine. The housing mounts to the engine and carr...
View full detailsBolt - M8 x 45 mm Torx-head flange bolt for the propshaft flange connection. The bolt secures the flange-type propshaft joint to the mating drive ...
View full detailsFront suspension bump stop - part of the front strut and coil spring assembly. The moulded rubber bump stop is fitted over the strut piston rod, b...
View full detailsBreather Hose for the crankcase ventilation circuit of the 2.2L Td4 diesel engine. Part of the crankcase emission control system, it connects to t...
View full detailsDowel Pin for the cylinder block, fitted at the front face of the block on the 2.2L Td4 (DW12) diesel engine. The dowel locates the mating compone...
View full detailsTensioner - Timing Belt
Hex-Head Bolt and Washer - bolt and washer assembly used in the front suspension and subframe area. The fastener secures front cross member, stabi...
View full detailsUpper Engine Mounting - component of the powertrain mounting system, forming the upper support point between the engine and the body structure. Th...
View full detailsAir Intake Duct in the engine induction system of the 2.0L 16V turbo petrol engine. The duct channels filtered intake air through the induction tr...
View full detailsHex Nut - M12 x 1.25 - fine-thread fastener used at the top mounting of the front suspension strut. It secures the strut rod at the upper mounting...
View full detailsTiming Chain - Secondary, Upper is part of the camshaft drive of the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4), including plug-in ...
View full detailsOil Pump for the 2.2L DW12 diesel engine, part of the engine lubrication system. Driven from the crankshaft, it draws oil from the sump and delive...
View full detailsClutch Slave Cylinder Assembly Concentric (hydraulic) clutch slave cylinder for the six-speed manual gearbox. Mounted concentrically around the ge...
View full detailsOutput Shaft Oil Seal for the ZF 9HP 9-speed automatic transmission (9HP48 / 9HP50). The seal is fitted in the transmission housing around the out...
View full detailsHydraulic Clutch Bearing Concentric hydraulic clutch release bearing (slave cylinder) for the six-speed manual gearbox. Mounted concentrically aro...
View full detailsExhaust Gas Pressure Sensor for the diesel exhaust aftertreatment system. The sensor is connected by take-off pipes to the exhaust upstream and do...
View full detailsFlanged Hex Nut. Used at engine mountings and front suspension strut fixing points.
Exterior mirror motor - left-hand side glass adjustment motor within the door mirror head. The motor sits behind the mirror glass and drives the g...
View full detailsFront Brake Disc, internally vented, 349mm diameter, for vehicles fitted with the 18" front brake caliper. It provides the friction surface for the...
View full detailsFront Brake Disc, internally vented, 349mm diameter, for vehicles fitted with the 18" front brake caliper. It provides the friction surface for the...
View full detailsRadiator Assembly for the engine cooling system. The radiator dissipates heat from the engine coolant as it passes through the core, maintaining op...
View full detailsFront Lower Engine Mounting is the lower insulator supporting the engine at the front of the mounting system. It locates the engine to the subfram...
View full detailsParts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible, this collection covers pre-facelift and post-facelift specifications. If you own the 2019-onward Evoque, see the L551 parts collection.
The Range Rover Evoque L538 is the first-generation Evoque, produced at Halewood, UK from July 2011 to 2019 under chassis code L538. Model years run from 2012 to 2019. The collection covers the 5-door and 3-door SUV variants (produced through to 2018) and the convertible (produced from 2016 to 2019).
The L538 rides on the D8 platform, also known as LR-MS, a high-strength steel monocoque architecture developed by Land Rover as a heavily modified derivative of the Ford EUCD base. The D8 platform is also used on the Land Rover Discovery Sport. This architecture gives the Evoque a car-like driving character distinct from the body-on-frame and aluminium-intensive platforms used in other Range Rover generations.
Drivetrain configuration varies by variant. Four-wheel drive vehicles use a Haldex-based on-demand AWD system. Front-wheel drive was available on select diesel variants, specifically the eD4, which used a single-clutch, front-axle-only setup for improved efficiency. Confirming your drivetrain before ordering driveline, coupling, or differential components is essential. Generation-specific Haldex AWD service information is published by Haldex.
This collection does not cover the Range Rover Evoque L551 (2019 onward). If your vehicle was registered from 2019 onward, use the L551 parts collection linked in the intro above this product grid.
The L538 production run splits into two distinct specifications at the 2015 model year.
Pre-facelift vehicles (model years 2012 to 2015) used Ford-derived powerplants. Petrol variants used the 2.0L Ford EcoBoost Si4 turbo four-cylinder. Diesel variants used the 2.2L Ford Duratorq (PSA DW12) in TD4 and SD4 states of tune. The automatic gearbox on pre-facelift vehicles is the 6-speed Ford Aisin AW F-21 unit, also designated the Aisin Warner TF-81SC.
Post-facelift vehicles (model years 2016 to 2019) introduced JLR's Ingenium engine family. Both petrol and diesel variants moved to the 2.0L Ingenium turbo four-cylinder. The 9-speed ZF 9HP automatic gearbox replaced the 6-speed unit on automatic variants. The 6-speed Getrag M66EH50 manual remained available in select markets on diesel variants throughout the production run.
Engine-specific parts including oil filters, timing components, gaskets, sensors, and turbo components are not interchangeable between the Ford-derived and Ingenium specifications. Always confirm your engine code and model year before ordering.
Reference note: ZF 9HP transmission technical information is published by ZF Group.
Fitment GuidanceThe most reliable method for confirming parts fitment on an L538 is your Vehicle Identification Number (VIN). The VIN is a 17-character code stamped on the door jamb plate, on the windscreen base near the A-pillar (driver or passenger side depending on market variant), and recorded in your V5C or national registration document.
The tenth character of the VIN encodes the model year. The eighth character encodes the engine variant. If you are ordering engine-specific parts, turbo components, gearbox parts, or any item that changed at the 2015 facelift, cross-referencing your VIN with the part number is strongly recommended before purchase.
If you are unsure which specification your vehicle is, contact the Budget Parts team directly. Trade account holders can request fitment confirmation through the wholesale portal.
Catalogue ScopeThis collection includes suspension parts such as control arms, bushings, drop links, anti-roll bars, shock absorbers, and wheel bearings. Brake parts include pads, discs, calipers, brake pipes, and brake hardware. Engine parts cover oil filters, sump washers, hydraulic tappets, expansion tank caps, and ancillary components. Drivetrain parts include propshaft bolts, driveshaft components, and wheel nuts. The collection also includes electrical parts such as relays and sensors, service and maintenance items including ATF fluids and service hardware, body and chassis fixings, and workshop supplies including brake cleaner and fastener assortments.
Use the category filter above to narrow results to your area of work. The quality filter allows you to select between Genuine Land Rover, OEM, and Aftermarket grades.
Quality TiersEvery part in this collection is marked with one of three quality grades.
Genuine Land Rover parts are sourced through the official Jaguar Land Rover distribution channel. They carry the original Land Rover part number and packaging. These are the appropriate choice when OEM provenance documentation is required, such as for warranty or insurance purposes.
OEM parts are produced by the same manufacturers that supply Land Rover directly, sold outside the official JLR channel. The component is frequently identical to the Genuine part. OEM is the standard choice for independent workshops and experienced owners who want original-specification quality without the official channel markup.
Aftermarket parts are independently manufactured. Quality varies by supplier and application. Each listing specifies the grade, and the product description notes any relevant fitment or application limitations. Aftermarket is appropriate for non-critical components or where cost is the primary constraint.
TradeBudget Parts operates a wholesale portal for registered independent workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. If you manage a workshop or operate as a parts buyer, visit the wholesale login page to access trade terms or register your account.
Generation ReferenceThe L538 is the first-generation Evoque. The second-generation Evoque, the L551, entered production in 2019 on the PTA platform with 48V mild-hybrid technology and Ingenium engines throughout. Parts are not interchangeable between generations.
For the full Range Rover model family and generation reference, see the Range Rover parts collection.
Technical GuidesThe articles below provide diagnostic and technical context relevant to Range Rover Evoque L538 owners and workshops. They support, but do not duplicate, the parts categories in this collection.
Technical guide to the L538 covering the Ford-to-Ingenium engine split, Haldex service requirements, and the suspension and platform architecture that defined the first-generation Evoque.
Range Rover Evoque L538 guide →Owner and workshop guide to the Evoque convertible covering the structural changes for the open-roof configuration, the electric roof system, AWD configuration, and common faults relevant to parts selection.
Range Rover Evoque convertible guide →The Freelander 2 shares Haldex AWD architecture and overlapping engine families with the Evoque L538. This guide covers Haldex service intervals, coupling failure patterns, and rear differential diagnosis that applies directly to L538 AWD variants.
Freelander 2 faults and Haldex service guide →The Range Rover Evoque L538 was produced from July 2011 to 2019. Model years run from 2012 to 2019. The 5-door and 3-door SUV variants were produced through to 2018. The convertible variant was introduced in 2016 and produced through to 2019. Parts availability in this collection covers the full L538 production window across all body styles.
If your vehicle was registered before 2019, it is almost certainly the L538 first generation. If registered from 2019 onward, it is the L551 second generation. The clearest confirmation is your VIN. The tenth character of your 17-character VIN encodes the model year. You can also check the driver's door jamb plate, which will show the build date and in some markets the chassis code. If you are unsure, contact Budget Parts directly before ordering.
The L538 was significantly updated at the 2015 model year. Pre-facelift vehicles use Ford-derived engines (2.0L EcoBoost petrol, 2.2L Duratorq diesel) and a 6-speed Aisin automatic gearbox. Post-facelift vehicles use JLR Ingenium engines (2.0L petrol and diesel) and a 9-speed ZF 9HP automatic. Engine-specific parts including oil filters, timing components, turbo components, and gaskets are not interchangeable between these specifications. Always confirm your model year and engine code before ordering.
Four-wheel drive variants of the L538 use an on-demand Haldex AWD system. This couples the rear axle electronically and distributes torque when front-axle slip is detected. Some diesel variants were available in front-wheel drive only, specifically the eD4, which does not use a rear differential or Haldex coupling at all. Confirming your drivetrain configuration before ordering rear axle, coupling, or propshaft components is important. If you are unsure, check your V5C or contact Budget Parts.
The L538 used two engine families across its production run. Pre-facelift vehicles (2012 to 2015 model year) used the 2.0L Ford EcoBoost Si4 turbo petrol and the 2.2L Ford Duratorq (PSA DW12) diesel in TD4 and SD4 outputs. Post-facelift vehicles (2016 to 2019 model year) used JLR's 2.0L Ingenium turbo four-cylinder in both petrol and diesel forms. Parts that are engine-specific are listed with applicable engine codes in the product descriptions.
The L538 uses the D8 platform, also known as the LR-MS. This is a high-strength steel monocoque architecture developed by Land Rover as a substantially redesigned derivative of the Ford EUCD base. The same platform underpins the Land Rover Discovery Sport. It is a different architecture to the aluminium-intensive platforms used on the Range Rover L405 and Range Rover Sport L494.
Yes. Budget Parts operates a wholesale portal for registered workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. You can register or log in through the wholesale portal link in the site header. For volume orders or specific part enquiries, contact the Budget Parts team directly.
Updated: 13 May 2026