for Discounts / VAT
for Discounts & Correct VAT
Parts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible. Covers pre-facelift and post-facelift specifications. Stock is held in the Netherlands and dispatched across the EU. Use the filters to narrow by model year, category, or quality grade.
Crankshaft Pulley mounts on the nose of the crankshaft at the front of the engine and drives the front-end accessory belt. Fitted to the 2.0L 16V ...
View full detailsWater Pump for the 2.0L Ingenium diesel engine (AJ20D4), part of the engine cooling circuit. Belt- or chain-driven from the engine, the pump circu...
View full detailsOil Cooler dissipates heat from the engine oil to help maintain a stable oil operating temperature. Fitted in the lubrication circuit of the 2.0L ...
View full detailsIntake Camshaft Sprocket for the 2.0L 16V TIVCT turbocharged petrol engine. Driven by the timing chain, it transmits crankshaft rotation to the int...
View full detailsCap Fuel Rrsport, Rrevo - Discovery 3, Discovery 4
Front Fog Lamp - exterior lighting unit that mounts into the lower aperture of the front bumper. The fog lamp produces a wide, low-set beam that l...
View full detailsClutch Repair Kit for the 6-speed manual transmission on the 2.0L Ingenium AJ200 diesel engine. The clutch transmits drive from the engine flywhee...
View full detailsOil Cooler and Filter Assembly combines the engine oil cooler and oil filter housing for the 2.2L TD4 diesel engine (DW12). Mounted in the lubrica...
View full detailsFront Axle Drive Shaft, right-hand side, transmitting drive from the front differential to the road wheel. Fitted to 2.2L diesel applications. The...
View full detailsOil Cooler and Filter Assembly combines the engine oil cooler and oil filter housing for the 2.2L TD4 diesel engine (DW12). Mounted in the lubrica...
View full detailsMass Air Flow Sensor measures the mass of air drawn into the engine and reports it to the engine control module for fuel metering. It mounts in th...
View full detailsNOx Trap Temperature Sensor - Rear from the exhaust aftertreatment system of the 2.0L I4 Ingenium diesel engine. The sensor occupies the rear posi...
View full detailsFront Door Latch is the locking and release mechanism for a front door, mounted in the shut face at the rear edge of the door. It engages the body...
View full detailsMacPherson Strut is the front suspension damper, forming the main vertical strut that locates the front wheel and controls its vertical movement. ...
View full detailsFuel Supply and Vapour Tube forming part of the underfloor fuel delivery and evaporative emission system on the 2.0L TIVCT turbocharged petrol engi...
View full detailsFuel Supply and Vapour Tube is a combined under-floor pipe assembly serving the fuel delivery and evaporative emissions systems. The supply line c...
View full detailsMass Air Flow (MAF) Sensor for the engine air intake system. Installed in the intake tract downstream of the air filter, the sensor measures the m...
View full detailsFuel Pump for the 2.0L TIVCT turbocharged petrol engine - the in-tank fuel pump and sender unit. Mounted inside the fuel tank, it draws fuel and d...
View full detailsElectronic Parking Brake Actuator for the rear brake caliper, part of the electronic parking brake (EPB) system. The actuator is a self-contained ...
View full detailsCamshaft Sprocket for the camshaft drive, mounted on the end of the camshaft and driven by the timing chain from the crankshaft. It transmits the d...
View full detailsFuel Pump and Sender Unit is the in-tank fuel delivery module for the 2.2L diesel. It draws fuel from the tank to feed the engine and incorporates...
View full detailsTow Bar Bracket - Flange Ball
Connecting Rod Kit for the 2.2L DW12 DOHC turbo diesel engine, supplied as a complete set of four connecting rods. The connecting rods link the pi...
View full detailsHigh-Pressure Fuel Injection Pump for the 2.0L GTDi turbocharged petrol engine. This engine-mounted pump raises fuel to the high pressure required ...
View full detailsRemote Ctrl Sys - Transponderorder
Camshaft Cover for the 2.0L 16V turbocharged petrol engine (Gen2), also known as the rocker cover. It seals the top of the cylinder head over the ...
View full detailsNOx Trap Temperature Sensor from the exhaust aftertreatment system of the 2.0L I4 AJ200 Ingenium diesel engine. The sensor reports exhaust gas tem...
View full detailsHeadlamp and Flasher Assembly for the front left-hand side, with an integrated direction indicator. Bi-Xenon (High-Intensity Discharge) headlamp u...
View full detailsHaldex Coupling Pump is the feed pump for the rear-axle Haldex coupling on all-wheel-drive models. Mounted to the Haldex unit at the rear axle, th...
View full detailsAir Conditioning Compressor - the belt-driven pump at the heart of the air-conditioning refrigerant circuit. It draws low-pressure refrigerant gas ...
View full detailsThrottle Body and Motor - the electronically actuated intake throttle valve for the 2.2L common-rail direct-injection diesel engine, mounted at the...
View full detailsEngine Oil Pan - the sump casing that closes the bottom of the cylinder block on the 2.2L 16V common-rail diesel (DW12) and forms the engine's oil ...
View full detailsTiming Belt Kit with Water Pump for the camshaft drive of the 2.2L DOHC diesel (DW12) engine. The timing belt synchronises crankshaft and camshaft...
View full detailsAlternator Assembly - the belt-driven charging unit that supplies the vehicle's electrical system and recharges the battery while the engine runs. ...
View full detailsAlternator Assembly - the belt-driven charging unit that supplies the vehicle's electrical system and recharges the battery while the engine runs. ...
View full detailsFuel Injector for the 2.2L Td4 common-rail diesel fuel injection system. The injector meters and atomises high-pressure diesel into the combustion ...
View full detailsA/C Evaporator for the air conditioning circuit, mounted within the heating and ventilation (HVAC) housing. The evaporator is the heat exchanger i...
View full detailsCamshaft Cover for the 2.0L 16V turbocharged petrol engine (Gen2), also known as the rocker cover. It seals the top of the cylinder head over the ...
View full detailsShaft Assembly - Drive - Drive Shaft and Hub
Tow Bar Kit - Quick Release
Oil Cooler - transmission oil cooler serving the 9-speed automatic transmission on all-wheel-drive applications. The cooler regulates automatic tr...
View full detailsEGR Cooler - low-pressure exhaust gas recirculation (EGR) cooler within the engine's EGR circuit, fitted to the 2.0L four-cylinder diesel (AJ200 / ...
View full detailsParking Camera, part of the surround camera and parking assistance system. It captures the video feed used by the driver assistance display during...
View full detailsCondenser is the air conditioning condenser, mounted at the front of the vehicle ahead of the cooling pack. It dissipates heat from the refrigeran...
View full detailsCamera - Parking
Intake Manifold for the engine air intake system. It distributes the incoming air charge evenly to the cylinder intake ports and carries the mounti...
View full detailsCoupling Pump is the electro-hydraulic pump that operates the rear axle all-wheel-drive coupling, generating the hydraulic pressure that engages th...
View full detailsCoupling Pump is the electro-hydraulic pump that operates the rear axle all-wheel-drive coupling, generating the hydraulic pressure that engages th...
View full detailsParts for the Range Rover Evoque L538, covering all variants from 2011 to 2019 including the 5-door, 3-door, and convertible, this collection covers pre-facelift and post-facelift specifications. If you own the 2019-onward Evoque, see the L551 parts collection.
The Range Rover Evoque L538 is the first-generation Evoque, produced at Halewood, UK from July 2011 to 2019 under chassis code L538. Model years run from 2012 to 2019. The collection covers the 5-door and 3-door SUV variants (produced through to 2018) and the convertible (produced from 2016 to 2019).
The L538 rides on the D8 platform, also known as LR-MS, a high-strength steel monocoque architecture developed by Land Rover as a heavily modified derivative of the Ford EUCD base. The D8 platform is also used on the Land Rover Discovery Sport. This architecture gives the Evoque a car-like driving character distinct from the body-on-frame and aluminium-intensive platforms used in other Range Rover generations.
Drivetrain configuration varies by variant. Four-wheel drive vehicles use a Haldex-based on-demand AWD system. Front-wheel drive was available on select diesel variants, specifically the eD4, which used a single-clutch, front-axle-only setup for improved efficiency. Confirming your drivetrain before ordering driveline, coupling, or differential components is essential. Generation-specific Haldex AWD service information is published by Haldex.
This collection does not cover the Range Rover Evoque L551 (2019 onward). If your vehicle was registered from 2019 onward, use the L551 parts collection linked in the intro above this product grid.
The L538 production run splits into two distinct specifications at the 2015 model year.
Pre-facelift vehicles (model years 2012 to 2015) used Ford-derived powerplants. Petrol variants used the 2.0L Ford EcoBoost Si4 turbo four-cylinder. Diesel variants used the 2.2L Ford Duratorq (PSA DW12) in TD4 and SD4 states of tune. The automatic gearbox on pre-facelift vehicles is the 6-speed Ford Aisin AW F-21 unit, also designated the Aisin Warner TF-81SC.
Post-facelift vehicles (model years 2016 to 2019) introduced JLR's Ingenium engine family. Both petrol and diesel variants moved to the 2.0L Ingenium turbo four-cylinder. The 9-speed ZF 9HP automatic gearbox replaced the 6-speed unit on automatic variants. The 6-speed Getrag M66EH50 manual remained available in select markets on diesel variants throughout the production run.
Engine-specific parts including oil filters, timing components, gaskets, sensors, and turbo components are not interchangeable between the Ford-derived and Ingenium specifications. Always confirm your engine code and model year before ordering.
Reference note: ZF 9HP transmission technical information is published by ZF Group.
Fitment GuidanceThe most reliable method for confirming parts fitment on an L538 is your Vehicle Identification Number (VIN). The VIN is a 17-character code stamped on the door jamb plate, on the windscreen base near the A-pillar (driver or passenger side depending on market variant), and recorded in your V5C or national registration document.
The tenth character of the VIN encodes the model year. The eighth character encodes the engine variant. If you are ordering engine-specific parts, turbo components, gearbox parts, or any item that changed at the 2015 facelift, cross-referencing your VIN with the part number is strongly recommended before purchase.
If you are unsure which specification your vehicle is, contact the Budget Parts team directly. Trade account holders can request fitment confirmation through the wholesale portal.
Catalogue ScopeThis collection includes suspension parts such as control arms, bushings, drop links, anti-roll bars, shock absorbers, and wheel bearings. Brake parts include pads, discs, calipers, brake pipes, and brake hardware. Engine parts cover oil filters, sump washers, hydraulic tappets, expansion tank caps, and ancillary components. Drivetrain parts include propshaft bolts, driveshaft components, and wheel nuts. The collection also includes electrical parts such as relays and sensors, service and maintenance items including ATF fluids and service hardware, body and chassis fixings, and workshop supplies including brake cleaner and fastener assortments.
Use the category filter above to narrow results to your area of work. The quality filter allows you to select between Genuine Land Rover, OEM, and Aftermarket grades.
Quality TiersEvery part in this collection is marked with one of three quality grades.
Genuine Land Rover parts are sourced through the official Jaguar Land Rover distribution channel. They carry the original Land Rover part number and packaging. These are the appropriate choice when OEM provenance documentation is required, such as for warranty or insurance purposes.
OEM parts are produced by the same manufacturers that supply Land Rover directly, sold outside the official JLR channel. The component is frequently identical to the Genuine part. OEM is the standard choice for independent workshops and experienced owners who want original-specification quality without the official channel markup.
Aftermarket parts are independently manufactured. Quality varies by supplier and application. Each listing specifies the grade, and the product description notes any relevant fitment or application limitations. Aftermarket is appropriate for non-critical components or where cost is the primary constraint.
TradeBudget Parts operates a wholesale portal for registered independent workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. If you manage a workshop or operate as a parts buyer, visit the wholesale login page to access trade terms or register your account.
Generation ReferenceThe L538 is the first-generation Evoque. The second-generation Evoque, the L551, entered production in 2019 on the PTA platform with 48V mild-hybrid technology and Ingenium engines throughout. Parts are not interchangeable between generations.
For the full Range Rover model family and generation reference, see the Range Rover parts collection.
Technical GuidesThe articles below provide diagnostic and technical context relevant to Range Rover Evoque L538 owners and workshops. They support, but do not duplicate, the parts categories in this collection.
Technical guide to the L538 covering the Ford-to-Ingenium engine split, Haldex service requirements, and the suspension and platform architecture that defined the first-generation Evoque.
Range Rover Evoque L538 guide →Owner and workshop guide to the Evoque convertible covering the structural changes for the open-roof configuration, the electric roof system, AWD configuration, and common faults relevant to parts selection.
Range Rover Evoque convertible guide →The Freelander 2 shares Haldex AWD architecture and overlapping engine families with the Evoque L538. This guide covers Haldex service intervals, coupling failure patterns, and rear differential diagnosis that applies directly to L538 AWD variants.
Freelander 2 faults and Haldex service guide →The Range Rover Evoque L538 was produced from July 2011 to 2019. Model years run from 2012 to 2019. The 5-door and 3-door SUV variants were produced through to 2018. The convertible variant was introduced in 2016 and produced through to 2019. Parts availability in this collection covers the full L538 production window across all body styles.
If your vehicle was registered before 2019, it is almost certainly the L538 first generation. If registered from 2019 onward, it is the L551 second generation. The clearest confirmation is your VIN. The tenth character of your 17-character VIN encodes the model year. You can also check the driver's door jamb plate, which will show the build date and in some markets the chassis code. If you are unsure, contact Budget Parts directly before ordering.
The L538 was significantly updated at the 2015 model year. Pre-facelift vehicles use Ford-derived engines (2.0L EcoBoost petrol, 2.2L Duratorq diesel) and a 6-speed Aisin automatic gearbox. Post-facelift vehicles use JLR Ingenium engines (2.0L petrol and diesel) and a 9-speed ZF 9HP automatic. Engine-specific parts including oil filters, timing components, turbo components, and gaskets are not interchangeable between these specifications. Always confirm your model year and engine code before ordering.
Four-wheel drive variants of the L538 use an on-demand Haldex AWD system. This couples the rear axle electronically and distributes torque when front-axle slip is detected. Some diesel variants were available in front-wheel drive only, specifically the eD4, which does not use a rear differential or Haldex coupling at all. Confirming your drivetrain configuration before ordering rear axle, coupling, or propshaft components is important. If you are unsure, check your V5C or contact Budget Parts.
The L538 used two engine families across its production run. Pre-facelift vehicles (2012 to 2015 model year) used the 2.0L Ford EcoBoost Si4 turbo petrol and the 2.2L Ford Duratorq (PSA DW12) diesel in TD4 and SD4 outputs. Post-facelift vehicles (2016 to 2019 model year) used JLR's 2.0L Ingenium turbo four-cylinder in both petrol and diesel forms. Parts that are engine-specific are listed with applicable engine codes in the product descriptions.
The L538 uses the D8 platform, also known as the LR-MS. This is a high-strength steel monocoque architecture developed by Land Rover as a substantially redesigned derivative of the Ford EUCD base. The same platform underpins the Land Rover Discovery Sport. It is a different architecture to the aluminium-intensive platforms used on the Range Rover L405 and Range Rover Sport L494.
Yes. Budget Parts operates a wholesale portal for registered workshops and trade buyers across the EU. The portal provides trade pricing and account-based ordering. You can register or log in through the wholesale portal link in the site header. For volume orders or specific part enquiries, contact the Budget Parts team directly.
Updated: 13 May 2026