Range Rover Evoque Parts

Expansion Tank Cap

Retaining Clip - a push-in trim retainer used to secure exterior mouldings and interior finisher panels. The nylon clip pushes into an 8 mm mounti...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Exhaust Gasket for the flanged joint between the exhaust front pipe and the catalyst section. It seals the bolted flange where the front pipe meet...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Wheel Centre Cap - set of four alloy wheel centre caps in Titan Silver. The centre cap clips into the hub bore of an alloy wheel, covering the hub...

Starter Motor - Defender TD4

Oil Filter Adaptor for the rear-drive Haldex coupling (Active On-Demand Coupling) in the all-wheel-drive driveline. The filter keeps the oil in th...

EGR Valve Gasket

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Washer Fluid Level Sensor for the windscreen washer system. The sensor fits into the washer fluid reservoir and monitors the volume of fluid remai...

Telematics Control Unit Backup Battery, a lithium-ion cell that supplies the Telematics Control Unit (TCU) when the main vehicle battery is disconn...

Kit - Key Fob Cover

Magnetic Oil Drain Plug for the engine oil sump on the 2.0L Ingenium (AJ200/AJ20) four-cylinder petrol and diesel engines. The plug seals the drai...

Retaining Clip - a fastener for exterior body mouldings and side-step trim. Secures body moulding and side-step trim panels to the bodywork.

Lower Knuckle Bolt, a hex-head M12 x 130 mm bolt for the front knuckle and hub assembly. It retains the lower end of the knuckle, clamping it to t...

Bolt securing the front suspension lower control arm at its rear fixing point. M14 x 90mm, Torx drive head.

Suspension Arm Nut - M16 flanged nut used on the rear suspension. It secures the lateral and lower arm pivot bolts where they pass through the sus...

Gasket polygon shape type. cover

Rear suspension arm bush, fitted at the front mounting position of the rear suspension arm. The bush forms the pivot between the suspension arm an...

Bolt securing a rear suspension arm to the rear knuckle. M14 x 75mm with a Torx head.

O-Ring - a 22.5 mm sealing ring used in the air conditioning refrigerant circuit. It seals a connection on the condenser and compressor side of th...

M14 x 105mm Bolt is a suspension and steering mounting fastener. It secures the rear suspension arm to the bearing hub, and is also used to mount ...

Rear Suspension Crosslink is a lateral locating link within the rear multi-link suspension assembly. It connects the rear subframe to the wheel kn...

Key Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...

Rear Crankshaft Oil Seal for the 2.0L AJ200-series four-cylinder engine, in both petrol and diesel applications. Seals the rear of the crankshaft ...

Pinion Flange Nut The retaining nut that secures the drive flange to the differential pinion shaft on the rear axle final drive. Tightened to a sp...

Rear Suspension Arm Washer is used at the rear knuckle and suspension arm mountings. It sits under the arm fixing bolt, spreading the clamp load a...

Washer Reservoir Cap closes the filler neck of the windscreen washer fluid reservoir. It seals the reservoir against debris ingress and fluid evap...

Nut - M5 x 12mm is a threaded securing nut with an M5 thread. It is a multi-application fastener used across a range of body, door and electrical ...

Micro Relay is a 20 amp, 4-pin switching relay used within the vehicle electrical system to control a high-current circuit from a low-current signa...

Catalyst Gasket for the exhaust system of the 2.0L 16V Ti-VCT four-cylinder petrol engine. This gasket seals the joint at the catalytic converter ...

Air Filter element for the engine air intake system. Fitted within the air filter housing, the element removes airborne dust and particulate matte...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Bolt is a threaded fastener used across several assemblies, including door latch mechanisms, front seat bases and anti-lock braking system mounting...

Exhaust Gasket sealing a flanged joint in the exhaust system on Land Rover and Range Rover models fitted with the 2.7L TDV6, 3.0D V6, 2.2D, and 4.4...

Upper Radiator Hose for the engine cooling circuit on the 2.0L Ti VCT petrol engine. This upper radiator hose carries engine coolant from the engi...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Door Latch for the front door, right-hand side, operating within the door lock control assembly. The latch engages the striker on the body aperture...

Wiper Blades - Front Pair is a replacement windscreen wiper blade set, supplied as a matched front pair for right-hand drive configurations. The bl...

Fuel Tank Heat Shield is the underbody heat barrier fitted between the exhaust system and the fuel tank. It reflects and insulates against radiant...

Rear Brake Pad Set for the rear disc brake assembly. These pads are installed in the rear brake caliper and press against the brake disc to delive...

Oil Filter filters the engine oil on the 2.0L 16V turbocharged petrol engine. Part of the oil cooler and filter assembly, it removes contaminants ...

pad foam OEM, eneregy absorbing. (Bij filter LR111341)

Oil Sealing Ring - Haldex - With Nut is the input flange sealing ring and retaining nut for the Haldex rear differential coupling unit. The sealin...