Range Rover Parts

Oil Filter for Land Rover petrol and diesel engines, part of the engine lubrication circuit. This screw-on canister filter threads onto the filter...

Hub Oil Seal - Inner for the front and rear wheel hubs, seating around the stub axle. The seal runs on the stub axle to retain hub lubricant and e...

Sump Plug Washer - copper sealing washer for the sump drain plug and thermostat housing on petrol and early diesel engines. The copper washer seat...

Nyloc Nut with a 3/8" UNF thread, used to secure propshaft flange bolts. A nylon insert set into the crown of the nut deforms over the bolt thread...

Hub Bearing - a tapered roller bearing for the front and rear axle wheel ends. It supports the rotating wheel hub on the stationary stub axle, carr...

Transfer Box Output Flange Oil Seal is a radial shaft seal fitted at the output flange of the LT230 transfer box, sealing between the rotating outp...

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Front cover oil seal

Nyloc Nut with a 1/2" UNF thread, used to retain suspension and steering ball-joint fixings. A nylon insert set into the crown of the nut deforms ...

Upper Link Ball Joint for the rear suspension A-frame (top link). The joint sits at the apex of the rear A-frame, where the frame meets the top of...

Hylomar Hylosil 100 is a neutral-curing RTV silicone sealant for gasketing, sealing and bonding in automotive and engineering applications. It cure...

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Diesel Fuel Filter - Cartridge is the replaceable filter element that seats in the fuel filter housing, upstream of the fuel injection pump in the ...

Nyloc Nut with a 3/8" UNF thread and a 12 mm across-flats hex, in the full-height (thick) form. A nylon insert set into the crown of the nut defor...

Fuel Tank Sender Sealing Ring for the fuel tank sender unit assembly. This sealing ring provides the fuel-tight seal between the fuel level sender...

Swivel Pin Housing Oil Seal - 9mm seal fitted to the front axle swivel housing. It seals the point where the drive shaft enters the swivel housing...

Gasket and Seal Kit for the LT230 transfer box, supplying the gaskets and seals needed to reseal the casing on overhaul. Used when the transfer bo...

Nyloc Nut with an M20 thread, used across suspension and driveline flange fastenings. A nylon insert set into the crown of the nut deforms over th...

Differential Pinion Oil Seal with a double sealing lip, for the front and rear differentials. It is press-fitted into the differential housing aro...

The Engine driven mechanical fuel lift pump is installed within the engine fuel system on 300Tdi diesel applications. This diaphragm-type pump mo...

Drive flange for the front axle drive shaft hub assembly. This component provides the splined connection between the drive shaft and the wheel hub,...

Hylomar Universal Blue is a non-setting gasket jointing compound for use on gaskets and machined metal joint faces in automotive and engineering ap...

Water Pump for the 300 Tdi 2.5L turbo diesel engine cooling circuit. The pump bolts to the engine front cover and circulates coolant through the cy...

Oil seal designed to retain lubricant and prevent contamination at the stub axle interface. The seal fits into the stub axle and forms a barrier b...

Inlet Manifold Gasket for the V8 petrol engine, forming the seal between the central inlet manifold casting and the cylinder head intake faces. It...

Hex Nut - 3/8" UNF - Full is a full-height plain hexagonal nut with a 3/8 inch UNF thread, used as a load-bearing imperial-thread fastener. It is ...

Reverse Lamp Bulb - a 21W 12V single-filament incandescent bulb (type P21W) with a BA15s single-contact bayonet cap, fitted to the rear lamp assemb...

Brake Pad Fitting Kit for front brake assemblies running vented discs. The kit supplies the retaining hardware that secures and correctly positions...

Spring Washer fitted under a nut or bolt head to resist loosening from vibration. An M8 split-ring (single-coil) spring washer. The sprung opening...

Water Pump Housing Gasket for the 300 TDi cooling circuit, sealing the coolant pump distance piece to the cylinder block. The gasket forms the coo...

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Split Pin locks a castellated (slotted) nut in place, passing through the nut slots and a cross-drilled hole in the shaft to stop the nut working l...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Reverse & Differential Lock Switch is a plunger-operated switch used in the manual gearbox and transfer box electrical circuits. The same swit...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Oil Cooler Pipe O-Ring for engine and transmission oil cooling circuits. This O-ring seals pipe fitting and hose connection joints in the oil cool...

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...

Hub Outer Oil Seal for the front and rear wheel hub assemblies. Located at the outer end of the hub, it retains the wheel-bearing grease within the...

Rocker Cover Gasket for the 2.5L 200TDi diesel engine, sealing the joint between the rocker cover and the cylinder head. Installed at the top of t...

Suspension and Chassis Mounting Bolt used across multiple suspension and chassis linkage positions. This hexagon bolt secures components including...

Anti-Roll Bar Washer used at the anti-roll bar and shock absorber mounting. The washer spreads the clamping load of the retaining nut across the m...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...