Range Rover Parts

Stud - M10 x 25mm, a threaded fastening stud used across a range of Land Rover assemblies. The stud provides a fixed threaded mounting point, allo...

Brake Caliper Guide Pin Set for the sliding (floating) disc brake caliper assembly. The guide pins locate the caliper to its mounting bracket and a...

Coolant Hose connects the bypass to the inlet manifold within the engine cooling circuit, for the 4.0L and 4.6L V8 EFI petrol engine. The hose car...

Ignition Lead Set for V8 petrol engines, forming part of the ignition system. The set carries the high-tension spark from the ignition coil and di...

Speedometer Drive Housing is the pinion (spindle) housing that fits to the rear flange of the LT230 transfer box. It carries the speedometer drive ...

Bonnet Cable is the bonnet release cable linking the cabin release lever to the bonnet latch mechanism. Pulling the interior release lever draws t...

Oil seal

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. This plastic plug cl...

Shock Absorber Bush Set - a set of four polyurethane bushes for the shock absorber mountings within the suspension damper assembly. Each bush seat...

Rubber Mounting for the body-to-chassis mounting points. The rubber is fitted under the body mounting bolt, seated between the body and the chassis...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Glass Fuse - 25A - a 25 A glass cartridge fuse for the vehicle's electrical circuits. The glass body carries a calibrated wire element between two...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Solenoid Valve Hose for the V8 EFI petrol engine, serving the plenum-mounted solenoid valve. Connects the solenoid valve into the intake plenum on...

Engine Overhaul Gasket & Seal Set for the 200TDi diesel engine, covering the bottom end of the engine. This set provides the gaskets and seals...

Hose pump to box

Track Rod End with right-hand thread, fitting at the outer end of the track rod within the steering linkage on the Defender, Discovery 1, and Range...

Aerial with cable Defender

Exhaust Olive is a tapered sealing ring used at the exhaust system's pipe joints. It seats between two pipe sections at a compression joint, formi...

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the fuel injection pump. It transmits pedal movement to the...

Alternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...

Universal Joint for the propeller shaft, of the 82mm cap-to-cap type. The universal (cardan) joint connects two sections of the propshaft, transmi...

Upper Link Bush for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. It seats in the upper (top) link to provide ...

Hex-head screw, 1/4" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Drain plug

Lower Arm Link – Rear is a rear suspension locating link connecting the rear axle to the chassis on coil-sprung suspension. It locates the axle fo...

Oil Filter for the engine lubrication system of the early V8 petrol engine. The filter removes metallic particles, carbon and other contaminants f...

Carrier for front calipers, fits both LH + RH

Air Filter element for the air cleaner housing on the induction system. The element traps dust and airborne particles from the incoming air before...

Side Repeater Lamp

Ignition heater plug timer glow plug relay

Brake Pipe Clip (double) used to route and secure rigid brake pipes within the braking hydraulic system. The double form retains two brake pipes s...

Edge Clip a body fixing that secures the bumper end caps to the bumper. It grips the edge of the end cap and clips it onto the bumper, holding the...

Exhaust Olive for the exhaust system. This tapered sealing ring fits into the slip joint between two exhaust pipe sections. As the joint clamp is ...

Lower Spring Seat locates the base of the coil spring in the suspension. It provides the lower bearing surface on which the road spring rests, pos...

Radius Arm Washer is a plain washer used at the radius arm mounting in the suspension. It seats under the radius arm fastener to distribute clampi...

Rear brake shield RH

Brake Disc Splash Shield - Front, RH, mounted behind the right-hand front brake disc. The shield sits between the stub axle / hub and the brake di...

Brake Disc - Solid - Rear is the rear brake disc, mounting to the rear hub and providing the friction surface the brake pads clamp against during b...

Gear Knob - LT95 is the hand grip fitted to the main gear lever of the LT95 4-speed gearbox. It threads onto the top of the gear lever and provide...

Viscous Fan Coupling - temperature-sensitive drive coupling between the water pump drive and the engine cooling fan. It modulates fan speed with u...

Radiator Top Hose is the upper coolant hose in the engine cooling circuit. It carries hot coolant from the engine thermostat housing to the top of ...

Rear Crankshaft Packing Strip (T-Piece) forms part of the rear crankshaft oil seal arrangement at the back of the cylinder block. The T-piece pack...

Inlet Manifold Gasket for the Rover V8 petrol engine, sealing the inlet manifold where it seats in the valley between the two cylinder banks. This...

Tow Ball Step is a rear access step that locates over the tow ball, providing two tread levels to make reaching the rear door, load area or roof ea...

Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing appli...

Bolt - Bracket to Chassis is an M10 x 60 mm fastener that secures a bracket to the vehicle chassis frame. It has a 10 mm nominal thread diameter a...

Exhaust Clamp Plate for the exhaust system, used at the front-pipe and catalyst joint. The plate works together with a U-bolt to draw the exhaust c...