Range Rover Parts

Engine Mounting Rubber (V8) supports the V8 petrol engine on the chassis and isolates its vibration from the bodyshell. The bonded rubber-to-metal...

Track Rod End Assembly for the steering linkage, connecting the track rod to the steering drop arm and transmitting movement from the steering box ...

Drive Screw - a No. 6 x 1/2" self-tapping drive screw used across door and facia assemblies. It secures the front door glass and window regulator,...

Blanking Plug for closing an unused 16 mm (5/8") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Oil Separator is part of the crankcase ventilation system on the 3.0L V6 diesel engine, separating oil mist from crankcase blow-by gases. The sepa...

Gasket kit 300tdi lower block set no rear crankshaft seal

Coolant Hose - Expansion Tank Vent is the bleed hose in the engine cooling system, connecting the radiator bleed outlet to the coolant expansion ta...

Radius Arm Bush mounts at the axle end of the front radius arm, within the front suspension radius arm and axle location assembly. It forms the co...

Spring Seat for the front coil spring suspension. It forms the lower seat that locates and supports the base of the front coil spring on the axle, ...

Upper Rear Tailgate Crossmember is the structural member spanning the top of the tailgate aperture, forming the upper edge of the rear body opening...

Oil Pump Shaft & Gear for the 3.5L V8 petrol engine, part of the lubrication system. The shaft and its drive gear transmit rotation from the ca...

Top Coolant Hose for the engine cooling circuit. Carries hot coolant from the engine outlet at the thermostat housing to the top tank of the radia...

Wheel Nut for alloy wheel fitment on Defender, Discovery 1 and Range Rover Classic. This tapered-seat wheel nut is designed for use with alloy whe...

Spring Washer, 5/16" - a single-coil split washer fitted under a nut or bolt head to maintain clamp tension. The split coil acts as a spring, exer...

Plug Washer for the drain and filler/level plugs on the LT95 gearbox and differential. The washer seats between the threaded plug and the casing t...

Oil Gallery Plug for the cylinder block oil gallery on Land Rover 4-cylinder engines. The oil gallery is the network of internal drillings in the ...

Steering Box Seal Kit reseals the input shaft of the 4-bolt power steering box within the power-assisted steering circuit. The input shaft is wher...

Service Kit - 300TDi for Land Rover Discovery 1 and Range Rover Classic with the 300Tdi 2.5L turbodiesel engine. This kit consolidates the key ser...

Screw 1/4" UNF x 1" screw used as a fixing in the upper section of the rear tailgate assembly.

Front Brake Caliper is the left-hand front caliper of the disc braking system, for the vented-disc setup. It clamps the brake pads against the fro...

Front Brake Caliper is the right-hand front caliper of the disc braking system, for the vented-disc setup. It clamps the brake pads against the fr...

Window Motor - LH for the front door electric window regulator system on the Range Rover Classic and Discovery 1. This is the left-hand motor unit...

Radius Arm Bush Set - polyurethane bushes for the front radius arm mountings at the axle end of the arm, supplied as a set of four in black. The b...

Thin Nut - a reduced-height hex nut with a 5/16" UNF (Unified Fine) thread. The shallow profile suits fastening points with limited clearance and ...

Radius Arm Bush is the compliant mounting bush at the radius arm pivot in the front suspension. The radius arm locates the front axle fore-and-aft...

Exhaust U-Bolt - a U-bolt clamp used to secure a joint in the exhaust system. It retains the exhaust front pipe (downpipe) connection, clamping th...

Tank Mounting Spacer - a spacer used in the fuel tank mounting assembly. It sets the correct standoff between the tank and its supporting bracketr...

Glazing Seal - the glazing rubber that lines the front door window channel and cushions the glass within it. It grips the edge of the glass, holds ...

Polyurethane Rear Upper A-frame suspension link bush set (NTC1773), chassis end.

Brake Disc Mud Shield - Front, LH, mounted behind the left-hand front brake disc. The shield sits between the stub axle / hub and the brake disc, ...

Heater Hose for the 200 TDi engine, forming part of the coolant circuit that supplies the heater matrix. Routes engine coolant to the heater core,...

Viscous Coupling - the temperature-controlled fan drive that turns the engine cooling fan on the 2.5 litre 300 TDi diesel. The coupling sits betwe...

Parking Brake Switch mounts on the handbrake lever assembly and operates the handbrake warning lamp in the instrument cluster. When the parking br...

Double Cardan Front Propshaft Kit - a heavy-duty front propshaft for the LT230 transfer box, using a double cardan (constant-velocity) joint at the...

Radius Arm Bolt with a 5/8" UNF (Unified National Fine) imperial thread and a 3-1/2" shank length. Secures the front radius arm to its axle or cha...

Bolt - M8 x 100mm hex head bolt used in the transmission mounting assembly. Secures transmission mounting components on Series III vehicles equipp...

Alternator assembly within the engine charging system, installed on the front-end accessory drive and driven by the auxiliary belt to convert mecha...

Joint Washer - a sealing washer for the piston-cooling oil squirt jet in the engine lubrication circuit. It seals the oil spray jet where it meets...

Self-Tapping Screw - a No. 8 x 3/8" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as it ...

Oil Pump Relief Plunger is the pressure-relief valve plunger within the engine oil pump, part of the lubrication system on the 3.5L V8 petrol engin...

Transmitter oil temperature for gauge with 140ºC dial scale

Oil Pump Gear for the 3.5L V8 engine oil pump, part of the lubrication system. The oil pump draws oil from the sump and pressurises it for deliver...

Brake caliper piston rear

Bracket tie bar for steering box

Anti-Squeal Shim for the rear brake pads - left-hand side. This shim fits between the brake pad backing plate and the caliper piston to dampen vib...

Disc brake

Clutch Lever Clip that retains the clutch release lever on its pivot post within the gearbox bellhousing. The clip holds the release fork onto the...

Drain plug