Range Rover Parts

Front Brake Caliper Guide Pin Set for the front disc brake calipers. The guide pins let the sliding caliper float on its carrier, so the caliper ca...

Starter Motor for the 3.5L V8 petrol engine, operating in the engine starting circuit. When energised through the starter solenoid, the pinion is ...

Bolt wishbone OEM

Fuel Pipe Union Nut for the fuel delivery line. This female threaded nut draws a fuel pipe up to its mating union, clamping the pipe's flared or c...

Sump Gasket for the Rover V8 4.0 and 4.6 petrol engine, sealing the oil sump to the underside of the cylinder block. This is the one-piece rubber-...

Left-hand inlet manifold for the 3.0L V6 diesel engine induction system. The manifold distributes intake air from the charge air system into the ...

Throttle Body Gasket seals the throttle body to the plenum chamber on the 4.0L and 4.6L V8 EFI petrol engine. Fitted between the throttle body and...

Sump Plug for the engine oil sump (oil pan), part of the engine lubrication system. It threads into the drain hole at the base of the sump to seal...

Bolt M8 X 16 HTSETS 8.8 S/COL sold EACH

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Rear Reflector a passive retroreflective marker mounted at the rear of the vehicle. It reflects the headlights of following traffic so the rear of...

Exhaust Tailpipe Silencer - Dual - LH

Exhaust Tailpipe Silencer for the right-hand side of a twin (dual) exhaust system. Forms the rearmost section of the exhaust, attenuating gas-flow ...

Propshaft

Brake Caliper - Rear - RH is the right-hand rear caliper of the disc brake assembly. Under hydraulic pressure from the rear brake circuit, it clam...

Knuckle Joint Bolt - an M14 x 88mm hex flange bolt securing the rear knuckle to the rear cross member. The integral flange spreads clamp load acro...

Belt Tensioner for the auxiliary (accessory) drive belt system. The spring-loaded tensioner arm and pulley maintain the correct tension on the ser...

Radiator Bottom Hose is the lower coolant hose of the engine cooling circuit. It carries cooled coolant from the radiator's lower outlet back towa...

Sealing Washer for the fuel injector, part of the diesel fuel injection system. The washer seats between the base of the injector and its bore in ...

Wheel Nut for securing an alloy road wheel to the hub. It threads onto the wheel stud and clamps the wheel against the hub mounting face, providing...

Bonnet Release Cable for the bonnet-release mechanism. It links the interior release lever to the bonnet latch: pulling the cabin lever draws the ...

Top Radiator Hose for the 2.5L 6-cylinder BMW diesel engine, forming the upper connection of the engine cooling circuit. It carries hot coolant fr...

Washer Jet for the windscreen washer system. This twin-nozzle jet mounts in the bonnet panel and directs two fan streams of washer fluid onto the w...

Headlamp Wiper Blade - wiper blade for the headlamp wash/wipe system. Fits onto the headlamp wiper arm and clears road spray and dirt from the hea...

Suspension Bolt Kit - the fitting hardware for a rear upper suspension arm (wishbone), used when replacing the arm at its mounting points. The kit...

Boost your vehicle's fuel economy and performance with the EGR Blanking Kit for Discovery 3 and Range Rover Sport 2.7 TDV6 engines (up to VIN 7A, n...

Hose Clip - Jubilee - 70-92mm is a worm-drive band clamp with a clamping range of 70-92 mm. It secures a hose over its spigot or connector, compre...

Thermostat for the 2.5L 300TDi diesel engine, operating within the thermostat housing at the top of the cooling circuit. The thermostat regulates ...

Front Coil Spring - Medium Duty, +2" Lift (Terrafirma). These front coil springs raise ride height by approximately 2 inches over standard and are...

Bolt - a hexagonal-head bolt with a 1/4" UNF (Unified Fine) imperial thread and a 1-1/4" length. Used as a body and chassis fixing at points such a...

Crankshaft Pulley mounts on the front of the crankshaft on the 200TDi 2.5L turbo diesel engine and drives the auxiliary drive belts. This pulley i...

Air Filter Element - Diesel

Bolt - 3/8" UNF x 4-1/4" is a structural fixing used in the front bumper and chassis frame assembly. It secures the front bumper and frame mountin...

Headlamp Wash T-Piece - three-way T-connector in the headlamp washer fluid line. Splits the feed hose from the washer pump so a single supply serv...

Drive Belt Tensioner Pulley for the V8 EFI petrol engine fitted with air conditioning, part of the ancillary belt drive. It tensions the drive bel...

Brake Pipe Clip from the brake hydraulic pipe routing. It secures and locates a rigid brake pipe against the chassis or body, holding the run of t...

Radiator Hose - Bottom is part of the engine cooling circuit. The lower hose carries cooled coolant from the radiator bottom outlet back to the en...

Exhaust Y-Pipe is the front section of the exhaust system, merging the outlets from both cylinder banks of the 3.5L V8 petrol engine into a single ...

Crankshaft Oil Seal seals the front timing cover where the crankshaft nose passes through it. Fitted to the 2.5L 300 TDi diesel engine, the seal r...

Window Regulator Handle for the front door, operating the manual window regulator (winder mechanism) to raise and lower the door glass. The handle...

Gearbox Mounting - left-hand transmission rubber mounting for the 2.5L 300 TDi diesel. This rubber-to-metal mounting supports the gearbox on the l...

Cigar Lighter - the panel-mounted lighter and 12V accessory socket in the instrument panel electrical system. The assembly comprises a socket and ...

Radiator with Integrated Oil Cooler - the main engine cooling radiator for the 200 TDi diesel engine, incorporating a built-in engine oil cooler an...

Transfer Box Lever Lock Nut used to secure the selector linkage at the transfer case. This half nut (thin profile locking nut) threads onto the sel...

Exhaust Tailpipe forms the rearmost section of the exhaust system, carrying exhaust gas from the intermediate silencer to the rear of the vehicle a...

Brake Master Cylinder Repair Kit for the Range Rover Classic hydraulic braking system. This rebuild kit contains the seals and components required...

Panhard Rod Bolt with a 1/2" UNF (Unified National Fine) imperial thread and a 3-1/4" shank length, manufactured to a high-tensile grade. Secures ...

Front Radius Arm Bush (rubber) located at the chassis end of the front radius arm. The bush is pressed into the radius arm mounting eye where the ...