Range Rover Parts

Steering Box Output Oil Seal for the manual, non-power-assisted steering box. It seals the output (rocker) shaft where it exits the steering box h...

Power Steering Pump Seal Kit supplying the housing and drive shaft seals for the cast-bodied power steering pump. The pump gaskets are supplied se...

Carb overhaul kit 175CD V8 Zenith Stromberg

Power Steering Pump Belt in the engine accessory drive system, driving the power steering pump. The belt transfers rotation from the crankshaft pu...

Lower Swivel Pin forming the lower pivot of the front axle swivel housing. The pin bolts to the underside of the swivel pin housing and carries th...

Clutch Slave Cylinder Repair Kit for the hydraulic clutch slave cylinder on the LT77 manual gearbox. The slave cylinder converts hydraulic pressur...

Windscreen Filler Strip closes and trims the gap between the windscreen glass and the body aperture, forming part of the windscreen sealing and fin...

Bonnet Release Cable for the Range Rover Classic. This cable runs from the interior release handle to the bonnet catch, allowing the bonnet to be ...

Main Switch: heavy-duty main switch rated at 1000 A.

Oil Pump Lock Tab, part of the engine oil pump assembly. The lock tab is a tab washer fitted under the oil pump retaining fastener; once the faste...

Split Pin locks slotted nuts, clevis pins and linkage joints against loosening, passing through a drilled hole and splayed to retain the assembly. ...

Plenum Chamber Hose Hose within the V8 EFI induction system, running from the plenum chamber to the starter motor housing. It connects the plenum ...

Taper Roller Bearing - shaft bearing for the R380 five-speed manual gearbox. A taper roller bearing carries both radial load and axial thrust, loc...

Brake Pad Set for the front axle disc brake assembly. The pads locate within the front calipers and clamp against the vented front discs, generatin...

Brake Disc - Rear - Solid

Flanged Nut M16 flanged nut for the rear suspension arm fixings. Part of the rear multi-link suspension assembly, it secures the lower and upper s...

Washer Adjusting washer for the rear suspension arm mounting. Part of the rear multi-link suspension assembly, it locates at the suspension arm pi...

ACE Seal Kit for the Active Cornering Enhancement valve block. The ACE system operates hydraulic actuators on the front and rear anti-roll bars to...

Stake nut RR3, RR4

Wheel Nut for alloy road wheels, part of the wheel mounting assembly. It threads onto the hub stud and clamps against the wheel's tapered nut seat ...

Right-hand inlet manifold forming part of the air intake system, distributing charge air from the throttle and intake ducting evenly to the cylinde...

Pollen Filter for the cabin air intake, part of the HVAC ventilation system. It installs in the intake housing upstream of the blower motor and eva...

Throttle Housing Seal for the 2.7L TDV6 and 3.0L SDV6 diesel engines, sealing the throttle body to the air intake. The seal sits between the throt...

Key Fob Battery Cover for the remote key fob. Encloses the fob battery compartment and retains the battery in place.

Breather hose rocker cover

Thermostat Housing for the engine cooling system of the 3.6L TDV8 (Lion) V8 turbo diesel. It houses the coolant thermostat and provides the connect...

Clutch slave cylinder assembly

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Heater O-Ring seal for the heater circuit. Seals a heater pipe or matrix connection against coolant leakage. Sold individually.

Tailgate Lower Cable Support Strap (Left-Hand) is the check strap that limits and supports the travel of the lower tailgate on a split tailgate. O...

Bolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...

Engine Oil Cooler for the diesel engine oil cooling circuit. This oil cooler assembly manages engine oil temperature by transferring heat between ...

Heater Blend Motor Servo for the HVAC air-distribution housing. The servo drives the blend flap that sets the ratio of hot to cold air, regulating ...

This special nut (thread size M14) is used in the rear suspension system across several Land Rover and Range Rover models. It plays a crucial role ...

Fuel Pump Seal for the fuel tank sender unit. This seal seats at the mounting flange of the fuel pump and sender unit where it interfaces with the ...

Ensure the secure and hassle-free lowering and raising of your spare wheel with this spare wheel winch, designed for Land Rover models with an unde...

Heater Adaptor is a connector fitting in the heater coolant circuit. It joins the heater hoses that carry engine coolant to and from the heater as...

Seat yoke

Tensioner

Ignition Coil Pack in the engine ignition system, generating the high-tension voltage that fires the spark plugs. Used on the distributorless V8 e...

Automatic Transmission Filter for the ZF automatic gearbox fluid circuit. It sits in the transmission fluid pan and filters the ATF drawn up into t...

Rear Trailing Arm Bush for the rear suspension, mounting the radius (trailing) arm to the chassis. The bush locates the arm while allowing the cont...

Parking Aid Sensor, Rear - ultrasonic transducer for the Parking Distance Control (PDC) system, mounted through the rear bumper cover. This is the ...

Plain Washer - metric M8 plain washer for use in general fastening assemblies throughout the vehicle. A standard flat washer used to distribute lo...

Thermostat for the 4.4L AJ V8 and 4.2L Supercharged V8 petrol engines, fitted within the engine cooling circuit. The thermostat regulates coolant ...

Rear Lower Suspension Arm for the rear independent suspension, left-hand side. The lower control arm (wishbone) connects the rear hub carrier to t...

Exterior Mirror Glass for the right-hand door mirror. The replaceable glass element locates into the exterior door mirror housing, providing the r...

Hose Clip - 12-20mm worm-drive hose clip suitable for hoses with an outside diameter of 12 to 20mm. This stainless-steel screw-type clip tightens ...