Range Rover Parts

Breather Adaptor - a threaded fitting in the axle and transfer case ventilation (breather) system. It screws into the axle casing or transfer case...

Alternator generates the vehicle's electrical charge, rated at 12V and 120A. Driven by the accessory belt from the crankshaft pulley, it charges t...

Brake Drum Clip is a retaining clip within the rear drum-in-hat parking brake (handbrake) assembly. It secures the handbrake shoe against the back...

Fuel Leak Off O-Ring seals the leak-off (spill return) connection at a diesel fuel injector. It sits in the injector leak-off circuit that collect...

Breather filter (M47 2.0L I4 16V Diesel) (M57 D30 3.0 Diesel)

Flanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...

Bonnet Gas Strut - a pressurised gas-filled damper forming part of the bonnet support system. Mounted between the bonnet and the body, it counterb...

Bump Stop - rubber suspension bump stop for the Range Rover P38, fitted to limit suspension travel at full compression and absorb the final impact ...

Alternator - 150A Water-Cooled - the charging unit for the vehicle's electrical system, mounted to the front of the engine and driven by the access...

Differential Assembly - a reconditioned 4-pin differential unit for the Land Rover-type axle. The differential sits at the centre of the axle, tak...

In-Tank Fuel Pump & Sender Unit for Range Rover P38A petrol applications. This combined assembly houses the electric fuel pump and fuel level s...

Rear Brake Caliper Seal Kit for rebuilding both rear brake calipers on the Discovery 2 and Range Rover P38, supplied as a pair to cover both sides ...

Air suspension compressor c/w drum

Auxiliary Drive Belt for the 2.7L TDV6 diesel engine on vehicles without an active roll stabiliser, 2092mm. This ribbed belt transmits drive from ...

Radiator Assembly for the Range Rover P38 cooling system, fitted to the 2.5L Diesel engine. The radiator dissipates heat from engine coolant circu...

Rear Brake Pad Set for the rear axle disc brakes. The friction pads are clamped by the rear brake calipers against the brake discs to generate the...

Fuel return tube O-ring seal

Outer CV Boot Kit for the outer constant velocity joint on the front driveshaft, fitting either side. The kit includes the rubber boot, circlip, r...

Fuel Filter Element for the diesel fuel supply system. The element removes particulate contamination and separates water from the fuel before it re...

Brake lever kit

Mainshaft Taper Roller Bearing supports the mainshaft at the 5th/reverse end of the R380 (and LT77) 5-speed manual gearbox. It carries the mainsha...

Clevis Pin used to secure a clevis or yoke joint in a mechanical linkage. The pin passes through the yoke and mating rod end and is retained by a ...

Camshaft Sprocket for the 4.0L and 4.6L V8 petrol engine, part of the timing drive at the front of the engine. It is driven by the timing chain fr...

Viscous unit

Filler Plug in blue anodised aluminium, replacing the standard cooling system filler and blanking plug at the thermostat housing. Seals against a ...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Wiper Blade for the front windscreen wash/wipe system, for left-hand drive applications. Fits the wiper arm clip and sweeps the windscreen in LHD ...

Suspension Bolt Kit - Front Lower is the fitting kit of nuts and bolts for the front lower suspension arm (wishbone), used to replace the original ...

Mirror glass LH

Bolt Threaded fastener used within the exhaust system assembly.

Brake hose

Brake Hose - Rear - flexible right-hand rear brake hose. It carries hydraulic pressure from the rigid chassis brake pipe across the suspension's m...

Brake Hose - Rear - flexible left-hand rear brake hose. It carries hydraulic pressure from the rigid chassis brake pipe across the suspension's mo...

Air Suspension Compressor Seal Kit reseals the piston assembly of the Dunlop electronic air suspension (EAS) compressor, restoring the seal between...

Engine Mounting - rubber engine mount that supports the engine on the chassis mounting bracket. The bonded rubber element carries the static weight...

Washer Jet - twin-nozzle windscreen washer jet for the front wash/wipe system. It seats in the bonnet or scuttle panel and directs two fine sprays ...

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Tailgate Support Cable supports the lower half of the split rear tailgate, limiting its travel and holding it level when opened. The cable links t...

Upper Front Suspension Arm Ball Joint The upper ball joint forms the top pivot between the front upper suspension arm and the wheel knuckle, holdi...

Upper Oil Cooler Pipe - feed pipe in the engine oil cooling circuit of the 4.0L V8 EFI petrol engine, carrying oil from the engine to the oil coole...

Rear Upper Knuckle Bush - a rubber-to-metal bush that forms the upper pivot mounting between the rear knuckle and the radius arm in the independent...

Propshaft Gaiter (Sliding Joint) is the flexible rubber boot that seals the sliding splined joint of the propshaft in the drivetrain. The sliding ...

Screw hex HD 3/8" UNC x 1-1/4"

Body Rivet - a mechanical fastener used within the body and panel assembly to join thin sheet metal, trim and stowage fittings. Nominal size 3/16"...

Heater Motor Adaptor Lead for the heater blower motor and fan assembly. This wiring adaptor bridges the blower motor to the vehicle's existing heat...

Ride Height Sensor - rear suspension height sensor for the self-levelling air suspension system. The sensor measures the position of the axle rela...

Steering Column Bolt for the lower steering shaft coupling. This pinch bolt clamps the lower steering shaft to its mating joint, securing the colum...

Mainshaft Bearing supports the mainshaft within the LT230 transfer box, carrying the shaft's rotational loads and keeping it running true as drive ...