Range Rover Parts

Heater Hose for the 200TDi engine cooling and heating circuit. This hose routes coolant from the engine cooling system to the cabin heater matrix,...

Heater Inlet Hose is a moulded coolant hose in the cabin heater circuit of the 200TDi 2.5L turbo diesel engine. It carries hot coolant from the en...

Exterior Door Handle Seal for the door locks and handles assembly. The seal sits between the outer door handle and the door skin, closing the gap ...

Bonnet Striker is part of the bonnet latch mechanism — the striker that the bonnet catch engages to hold the bonnet closed. When the bonnet is shu...

Window Regulator for the left-hand front door, operating the manual window lift mechanism. The regulator converts the rotation of the winder handl...

Oil Sump Drain Plug, bolt and washer assembly, for the Rover V8 EFI engine. The drain plug seals the oil sump drain aperture at the base of the en...

Brake Disc - a vented front brake disc for the front axle braking system. The disc rotates with the front wheel hub and is clamped by the caliper ...

Release Bearing Guide - the guide sleeve in the clutch release mechanism, mounted on the front cover of the manual gearbox. It encircles the gearb...

DIFFERENTIAL - ASSEMBLY - FRONT AXLE - 24 SPLINE - 4 BOLT FLANGE - D2

Yoke Transmission

Joint Washer - LT77 Front Cover seals the mating face between the front cover and the main casing of the LT77 5-speed manual gearbox. The washer p...

Upper Front Swivel Pin for the front axle swivel housing assembly. The upper swivel pin bolts to the top of the swivel housing and forms the upper...

Clutch Driven Plate for the V8 clutch assembly. It is carried on the gearbox input shaft between the flywheel and the clutch cover (pressure plate)...

Outer Shim - 1.35mm - Front Halfshaft / CV Joint This 1.35mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Half Shaft Shim is a 1.05mm selective shim used in the front axle drive shaft and hub assembly. It sets the endfloat of the front half shaft drive...

Camshaft for the five-bearing four-cylinder engine, running in the cylinder block as the core of the overhead-valve valvetrain. Driven from the cr...

Engine Cooling Fan - 11-blade, 17-inch diameter mechanical fan for the engine cooling system. Driven from the front of the engine via a viscous co...

Intercooler Hose for the 200 TDi turbocharged induction system. Part of the charge-air ducting that links the intercooler into the boost circuit, ...

Crankshaft Pulley Bolt for the 2.5L 300TDi diesel engine. This bolt secures the crankshaft pulley and torsional vibration damper to the nose of the...

Rocker Shaft Clamp for the cylinder head valve train on the 300TDi 2.5L turbo diesel engine. Secures the rocker shaft to the cylinder head pedesta...

Intercooler Hose for the 2.5L 300TDi 4-cylinder turbo diesel engine on EGR-equipped variants. This rubber hose connects the intercooler to the int...

O-Ring - Oil Pick-Up Pipe for the 2.5L 300TDi 4-cylinder turbo diesel engine. This O-ring seals the oil pick-up pipe connection at the oil pump or...

Inlet Valve Rocker Arm - a valvetrain component in the rocker shaft assembly of the 2.5L 300 TDi turbo-diesel engine. Mounted on the rocker shaft,...

Exhaust Valve Rocker Arm - a valvetrain component in the rocker shaft assembly of the 2.5L 300 TDi turbo-diesel engine. Mounted on the rocker shaf...

Oil Separator Drain Hose for the crankcase ventilation system on the 2.5L naturally aspirated diesel and 200TDi turbo diesel engines. It drains th...

Spring Retaining Plate for the front coil spring suspension. The plate seats the upper end of the front coil spring against the chassis spring seat...

Receiver Dryer for the air conditioning system, compatible with R134a refrigerant. Installed on the high-pressure side of the A/C circuit, between...

Steering Box Oil Seal Oil seal for the input (worm) shaft of the manual, non-power (Gemmer) steering box, sealing around the shaft where it enters ...

Accelerator Cable for EFI engines - left-hand drive applications. This cable runs from the accelerator pedal to the throttle body, transmitting pe...

Bolt is a 3/8" UNF threaded fastener used in body and chassis structural assembly, securing frame and rear-end structure components.

Anti-Roll Bar is the rear stabiliser bar within the suspension system, mounted transversely across the rear axle. Connected to the suspension thro...

Washer Pump draws fluid from the washer reservoir and delivers it to the windscreen jets. Mounted in the base of the washer bottle, this pump serv...

Switch window lift

Brake Light Switch operates the stop lamps within the braking system's electrical circuit. Mounted at the brake pedal, the switch closes when the ...

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

Viscous Fan Assembly for the engine cooling system, mounting to the viscous coupling unit on the front of the engine. This 16", 7-blade white fan ...

Rocker Cover Breather Hose - Left-Hand for the crankcase ventilation system of the Rover 3.5L V8 twin-carburettor engine. This hose connects the l...

Vacuum unit

Distributor O-Ring, the sealing ring for the ignition distributor on the 3.5L V8 petrol engine. The O-ring seals the distributor base where it loc...

Power Steering Filter for the power-assisted steering (PAS) fluid reservoir, part of the Steering Hydraulic Circuit. This filter element sits insi...

Accelerator Cable for left-hand-drive applications, forming part of the throttle control linkage. The cable connects the accelerator pedal to the ...

Fuel Pump Adaptor for mounting the external fuel pump on petrol engines. It provides the interface between the external fuel pump and its mounting...

Mounting Link Bottom Range Rover Classic

Rear Propshaft transmitting drive from the transfer box rear output to the rear axle differential. The shaft carries torque from the transfer box ...

Gearbox Side Cover Gasket for the LT95 4-speed V8 gearbox. This gasket seals the side cover to the gearbox casing, preventing oil leaks from the ge...

Body Mount Spacer Tube forms part of the body-to-chassis mounting assembly, located at a mount point between the body and the chassis frame. It se...

Plain Washer - a flat load-spreading washer used at the body-to-chassis mount fixings. Fitted under the bolt head or nut, it distributes clamping ...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...