Range Rover Parts

Suppressor Capacitor mounted at the ignition coil as part of the ignition system. It suppresses the radio-frequency interference generated by the ...

PAS Pump Gasket Set for the cast-bodied power steering pump on the 3.5 V8. It provides the gaskets for resealing the pump when it is dismantled fo...

Festoon Bulb - 12V 21W is a double-ended festoon-type incandescent bulb rated at 12V 21W, fitted with contacts at both ends for installation in spr...

Distributor Drive Gear - V8

Fuel Filler Cap Seal for the fuel system of the Range Rover Classic. This rubber seal fits the hinged (flip-up) fuel filler cap and creates a fuel...

Steering Valve Ring is a PTFE sealing ring used within the rotary valve of the Adwest power steering box. It seals between the pressure lands of t...

Heater Matrix for the cabin heater assembly, mounted inside the heater box within the HVAC housing. Engine coolant is circulated through the matri...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Cylinder Head Dowel for the V8 petrol engine. The dowel is a locating pin fitted to the cylinder block deck that positively registers the cylinder ...

Centre Silencer for the V8 single exhaust system. This intermediate silencer sits between the front (down) pipe and the rear silencer, providing t...

Rear Silencer & Tailpipe for the V8 single exhaust system. This is the rearmost section of the exhaust, combining the rear silencer and tailpi...

Swivel Pin Housing Joint Washer - RRC

Upper Swivel Pin forming the upper pivot of the front axle swivel housing. The pin bolts to the top of the swivel pin housing and runs in the uppe...

Swivel Pin Housing Shim - 0.010in is a 0.010 in (0.25 mm) shim used to set the bearing preload in the front axle swivel pin housing assembly. Fitt...

Oil Pressure Transmitter for the V8 engine oil pressure gauge circuit. This single-terminal sender threads into the engine oil gallery and varies ...

Hex Nut - 7/16 UNF fixing nut. Used on the fuel pipe unions of the 3.5L V8 twin-carburettor petrol engine. Also supplied as part of a service kit.

Gearbox Selector Pad for the LT77 five-speed manual gearbox. Fits the 5th gear selector within the selector and yoke assembly, forming the bearing...

Windscreen Filler Strip closes and trims the gap between the windscreen glass and the body aperture, forming part of the windscreen sealing and fin...

Fresh Air Grille Finisher for the fresh air intake, left-hand side. This capping finisher trims the fresh air intake grille on the body, covering ...

Engine Plug is a core (welch) plug that seals the casting holes in the engine. Fitted to the cylinder block, cylinder head water jacket and inlet ...

Battery Wing Nut secures the battery hold-down clamp within the battery mounting assembly, threading onto the clamp rod to hold the battery firmly ...

Crankcase Breather Valve for the crankcase ventilation system of the 4.4L V8 petrol and 4.2L supercharged V8 petrol engines. It regulates the flow ...

Rocker Assembly Aluminium - LH

Oil filter - Range P38 2.5L 6-cilinder BMW Diesel Type B, no bolt. From Engine number 33988348 onwards

Glow Plug for the 2.5L six-cylinder BMW M51 diesel engine, screwed into the cylinder head as part of the cold-start pre-heat system. The glow plug...

Clutch Slave Cylinder Repair Kit - a service kit for reconditioning the hydraulic clutch slave cylinder on the R380 5-speed manual gearbox. The cl...

Rear Brake Caliper - Left-Hand is part of the rear braking assembly, mounting over the rear brake disc on the left-hand side of the vehicle. The c...

Locking Wheel Nuts Land Rover Discovery 3 Discovery 4 Range Rover 2002 - 2013 Rover Sport 2005 - 2014

Anti Roll Bar Link - Rear connecting the rear anti-roll bar to the suspension trailing arm. This drop link bolts between the rear anti-roll bar an...

Intercooler Hose - Upper - LH for the charge air intercooler circuit on the 3.6L TDV8 Twin-Turbo V8 Diesel engine. This upper left-hand hose is pa...

Hose Intercooler - TDV6

Top Radiator Hose for the Range Rover L322 cooling system, fitted to the M62 B44 4.4L V8 Petrol engine. The upper radiator hose connects the engin...

Intercooler Hose - RH for the charge air intercooler circuit on the 3.6L TDV8 Twin-Turbo V8 Diesel engine. This right-hand hose is part of the int...

Pollen Filter for the cabin ventilation system, installed in the HVAC air intake housing. It traps pollen, dust and airborne particulates from the...

Brake Caliper Piston for the rear hydraulic disc brake assembly. The piston sits within the caliper bore and transfers hydraulic pressure from the...

Nyloc Nut - M16 for use in the front axle steering knuckle assembly. This M16 self-locking nut uses a nylon insert to provide prevailing-torque re...

Front Radius Arm - LH is a suspension linkage in the front suspension assembly. It connects the front subframe to the wheel knuckle and controls th...

Front Radius Arm - RH is a suspension linkage in the front suspension assembly. It connects the front subframe to the wheel knuckle and controls th...

Exhaust Manifold Gasket - Turbo to Manifold for the turbocharger and exhaust manifold assembly on the 3.0L TDV6 V6 diesel engine. This gasket seal...

Wheel Hub Assembly for the front and rear axle knuckle assembly. This wheel hub assembly mounts to the steering or rear knuckle and houses the whe...

Arm front suspension with four corner air suspension RH lower

Exhaust Manifold Nut is an M8 flanged hex nut that secures the exhaust manifold and turbocharger mounting flanges to the cylinder head. The copper...

O-Ring sealing the air filter housing to the airflow meter on V8 EFI engines. This O-ring seals the joint between the air filter housing outlet an...

Thermostat Assembly for the 4.4L V8 M62 petrol engine cooling circuit, in the air-conditioned configuration. The thermostat regulates coolant flow...

Oil Sealing Ring - Haldex - With Nut is the input flange sealing ring and retaining nut for the Haldex rear differential coupling unit. The sealin...

Tow Hook Cover for the front bumper. Fills the tow hook aperture in the front bumper when a tow hook or recovery hook is not fitted. Maintains the...

Valve - Control

O-Ring for the oil strainer in the ZF 4-speed automatic transmission. This seal fits the oil strainer (the automatic transmission fluid pickup fil...