Range Rover Parts

Front Exhaust Pipe forms the first section of the exhaust system, carrying gases from the engine downpipe rearward into the rest of the exhaust lin...

Choke Cable for the Range Rover Classic V8 engine, specific to vehicles fitted with Solex carburettors in left-hand drive configuration. This cabl...

Choke Cable for carburettor-equipped engines, right-hand-drive configuration. The cable links the dashboard choke control to the choke lever on th...

Steering Lock is the steering column lock and ignition switch assembly, mounted on the upper steering column. Turning the key operates the ignitio...

Exhaust Front Pipe - Y-Piece

Coil Spring for the front road suspension, fitted on the right-hand side. It forms part of the front coil-sprung suspension assembly, supporting ri...

Front Door Latch right-hand door latch mechanism, part of the door locking assembly. Engages the door striker to hold the front door closed, relea...

Sending is only possible by pallet. Too fragile for normal parcel delivery.

Front Inner Wing panel, complete, for the right-hand (offside) front wheel arch on the Range Rover Classic. The inner wing forms the structural in...

Front outer wing panel for the left-hand side, moulded in ABS to replace the original outer wing skin over the inner wing structure. This is the e...

Rear Wheel Arch Extension - Front Section, Left-Hand for the two-door body, an exterior body trim panel. This extension fits to the forward part o...

Bulkhead End Panel - Right Hand is a body repair panel that closes the outer right-hand end of the bulkhead (firewall) assembly - the structural pa...

Outer Repair Sill - 4-door body, right-hand (offside). A body repair panel for the outer sill section beneath the door openings. The outer sill is...

Outer Sill - external sill panel for the right-hand side of the two-door body. The outer sill is the visible rocker panel spanning the lower body b...

Cylinder Head for the 300 TDi 2.5L four-cylinder turbo diesel engine, supplied as a bare casting without valves. The head bolts to the top face of...

Intercooler - the charge-air cooler in the induction system of the 300Tdi 2.5L four-cylinder turbo diesel engine. Mounted in the airflow at the fr...

Thrust Washer - mainshaft thrust washer for the R380 five-speed manual gearbox. Located at the mainshaft 5th/reverse gears, it controls end-float ...

Baulk Ring - synchroniser baulk ring for the R380 five-speed manual gearbox. Serves the mainshaft 3rd/4th and 5th/reverse synchroniser hubs, match...

Synchromesh Ring for the five-speed manual gearbox mainshaft. The synchro (baulk) ring matches the speed of the gear to the synchro hub before eng...

Differential Reconditioned 10 Splines

Swivel Pin Thrust Washer - Upper is the shim washer that sits above the upper swivel pin bearing in the front axle swivel housing assembly. It set...

Swivel Pin Bearing is the upper needle-roller thrust bearing in the front axle swivel housing assembly. It mounts on the upper swivel pin and carr...

Differential Fixing Bolt used on the front and rear axle differential assemblies. It is one of the bolts securing the differential assembly, clamp...

Baulk Ring (Synchroniser Ring) for the LT77 five-speed manual gearbox. Fits the mainshaft synchromesh hubs to match shaft speeds during gear engag...

Transfer Box Differential Lock Clevis in the centre differential lock linkage. Connects the diff-lock actuating linkage that engages and releases ...

Detent Spring for the LT230 transfer box. It loads the detent that holds the high and low range and differential lock selectors in position, preven...

O-Ring for the LT77 five-speed manual gearbox. It seals the mainshaft and extension case joint against transmission oil loss.

Thrust Washer - intermediate shaft thrust washer for the LT95 four-speed gearbox. It controls the end-float of the intermediate (lay) shaft, takin...

Camshaft - the valvetrain camshaft for the overhead-valve V8. Driven from the crankshaft, its lobes act through the tappets, pushrods and rocker ar...

Copper Sealing Washer - a crush washer used to seal banjo and union connections throughout the diesel fuel system, at fuel pipes, filters and sedim...

Exhaust Front Pipe for the exhaust system on 200 TDi diesel applications (non-catalyst, manual transmission). It connects the turbocharger/manifol...

Intercooler Hose the upper charge-air hose in the intercooler circuit of the 200TDi diesel engine. It carries cooled, pressurised charge air from ...

Fuel Tank Cradle the support cradle that carries the fuel tank on the chassis. The cradle bolts to the chassis and supports the underside of the f...

Flywheel Assembly for the manual transmission on the 2.5L 200 TDi and 300 TDi turbo diesel engines. Bolted to the rear of the crankshaft, the flyw...

Tappet Adjusting Screw for the 2.5L 300 TDi turbocharged diesel engine, fitted in the rocker arm of the valvetrain. Threaded into the rocker arm t...

EGR Pipe Hose for the 2.5L 300TDi 4-cylinder turbo diesel engine. This rubber hose forms part of the exhaust gas recirculation (EGR) circuit, conn...

Camshaft operates the valvetrain of the 2.5L 300TDi diesel engine. Its lobes actuate the pushrods to open and close the inlet and exhaust valves.

Rocker Arm operates on the rocker shaft in the 200TDi diesel valvetrain. Driven by the pushrod, it transfers camshaft motion to actuate the valve.

Relief Valve Spring is the coil spring that controls the opening pressure of the oil pressure relief valve in the 300Tdi engine lubrication system....

Woodruff Key locating the camshaft sprocket on the Rover V8 engine. Fits the 3.5L, 3.9L and 4.2L Rover V8. Not used on the 4.0L or 4.6L engines.

Injector O-Ring is a sealing ring fitted to a fuel injector in the V8 EFI (electronic fuel injection) system. It seals the injector against its mo...

Rear Spring Spacer Kit for the coil-spring rear suspension, supplied as a pair of blocks that fit between the axle and the spring seats to raise ri...

Limited-Slip Differential is a helical-gear (Detroit TrueTrac type) limited-slip differential centre for the rear axle, with a 10-spline output. T...

Ensure a secure and reliable installation of your heavy-duty rear bumper with this fitting kit, specifically designed for bumper part DA5647. This ...

Winch Bumper Fitting Kit - the mounting hardware set for installing the DA5621 steel winch bumper. Supplies the fixings needed to attach the bumpe...

Rear Radius Arm locates the axle and controls its fore-and-aft movement, with geometry set for a 2 inch suspension lift. The revised arm restores ...

Air Filter - air filter for the 3.5 V8 carburettor engine, fitted at the carburettor intake to filter incoming air before it is drawn through the c...