Range Rover Parts

Rear Wheel Arch is the inner body panel that forms the arch over the rear wheel, part of the rear body assembly. This is the two-door version, whi...

Mass Air Flow Sensor - air mass meter fitted in the induction tract as part of the engine management system. The sensor sits in the intake ducting...

Selector Fork is the 1st/2nd gear selector fork for the 5-speed manual gearbox. It engages the 1st/2nd synchroniser sleeve, moving it along the ma...

Parking Sensor Speaker is the audible warning speaker for the rear parking aid system. It produces the proximity warning tone driven by the parkin...

Top Link Bracket for the rear suspension, right-hand side. This chassis-mounted bracket provides the upper pivot point for the rear suspension lin...

Inner Tie Rod for the rack-and-pinion steering linkage. The inner tie rod threads into the end of the steering rack and houses the inner ball join...

Kit diff wh OEM NLA AFTER STOCK ENDS

Manifold Pipe for the 2.7L TDV6 diesel engine. This pipe is part of the manifold assembly on the 2.7 TDV6 diesel engine. Replacement is required w...

Exhaust Bracket for the exhaust system mounting. The bracket supports and locates a section of the exhaust line against the underbody, typically w...

Spark Plug Well Gasket seals the spark plug aperture in the camshaft (valve) cover on the right-hand cylinder head bank. It prevents engine oil fr...

Ride Height Sensor - front right-hand corner sensor for the electronic air suspension system. Mounted between the chassis and the front suspension...

Oil Filter Adaptor for the engine lubrication circuit, mounting the oil filter to the cylinder block. The adaptor forms the interface between the ...

Piston Assembly - +0.020" Oversize for the 300Tdi 2.5L 4-Cylinder Turbo Diesel engine. This piston is machined to a diameter 0.020" (approximately...

Suspension Arm - Front - RH is a front control arm fitted to the right-hand side of the front suspension assembly. It locates the front wheel hub ...

Air Filter is an air cleaner element that filters intake air within the air cleaner assembly. On V6 and V8 applications it is the left-hand elemen...

Front Brake Pad Set for the front axle. Supplied without fitting springs.

Main bearing kit 0.020" undersize OEM AE

Coolant temperature transducer for the 3.9L V8 EFI petrol engine, part of the engine management sensing circuit. Threads into the coolant passage ...

Bearing transfer box LT230 intermediate shaft

Power Steering Pump - V8

Castor Correction Kit - 44mm Wide Bush for the front suspension radius arm assembly on the Defender, Discovery 1, and Range Rover Classic. Lifting...

Rear Wheel Arch Front Extension - RH is the front section of the right-hand rear wheel arch extension for 2-door bodyshells. It forms the leading ...

Radiator Frame – Top, the upper section of the radiator mounting frame. The top frame retains and locates the upper edge of the radiator within th...

Universal Joint, heavy-duty, for wide-angle propshafts. The wide-angle geometry allows the joint to operate at the increased angles produced by li...

Coil Spring Conversion Kit that replaces the Electronic Air Suspension (EAS) with conventional coil springs, eliminating the recurring faults and m...

Footwell Repair Panel - Right-Hand is a weld-in body repair section for the front footwell of the floor assembly. It replaces the original offside...

Ignition Lead - King The king lead in the high-tension ignition circuit. It carries the high-tension output from the ignition coil tower to the ce...

Carburettor Needle is the tapered metering needle that sets the fuel mixture in the carburettor. The needle moves within the jet to control fuel d...

Piston for the 3.5L Rover V8 petrol engine, supplied at +0.020" oversize with an 8.13:1 compression ratio. The +0.020" oversize suits a rebored bl...

Rear Wheel Arch Mudflap Mounting Panel - Left-Hand (LH) is a body panel fitted at the rear wheel arch. It bolts to the bodywork behind the rear wh...

Axle Spring Mount forms the lower seat for the rear coil spring, welding onto the rear axle casing to locate and retain the base of the spring. Th...

Radiator Frame – Bottom, the lower section of the radiator mounting frame. The bottom frame retains and locates the lower edge of the radiator wit...

Steering Box is the power-assisted recirculating-ball steering gear that converts rotation of the steering column into the swing of the drop arm, w...

Joint Washer for the manual gearbox top cover. This gasket seals the joint between the top selector cover and the gearbox case, retaining the gearb...

Bush for the axle and suspension assembly. This bush fits within a suspension or axle mounting point to absorb vibration and provide compliant art...

Upgrade your Land Rover Discovery 1 or Range Rover Classic with these heavy-duty steering arms, designed for superior strength, durability, and ste...

Injector Clamp secures a fuel injector into the cylinder head on the 2.5L 300TDi turbo diesel engine. It clamps the injector body down against its...

Shock Absorber A hydraulic telescopic shock absorber (damper) for the front suspension. It damps spring oscillation to control body movement and m...

Vacuum Advance Unit for the ignition distributor on the 3.5L V8 petrol engine. This vacuum capsule mounts on the side of the distributor and conne...

Conrod Bearing Set - V8 (0.020" Undersize) is a complete set of big-end bearing shells for the connecting rods of the Rover V8 petrol engine. The ...

Bumper Mounting Bracket - front bumper mounting, left-hand side. This bracket forms part of the front bumper mounting and secures the bumper to th...

M5 blind rivet nut (nutsert) - a threaded insert for sheet-metal and box-section fixings. The nutsert is placed in a single drilled hole and set w...

Window Regulator for the right-hand front door, operating the manual window lift mechanism. The regulator converts the rotation of the winder hand...