Range Rover Parts

Clutch Master Cylinder Overhaul Kit for rebuilding a CV-type master cylinder, allowing the worn internal components to be renewed without replacing...

Bolt - a hexagonal-head bolt with a 3/8" UNF (Unified Fine) imperial thread and a 1" length. Used as a suspension and chassis fixing at points such...

Clutch Release Fork - Heavy-Duty is the pivoting lever in the clutch release mechanism that acts on the release bearing. Operated by the clutch sl...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

Timing Belt Kit for the camshaft drive of the 2.5L 300 Tdi turbo-diesel engine. The timing belt synchronises crankshaft and camshaft rotation to m...

Fuel Filter Housing Assembly for the fuel delivery line on carburettor petrol engines, including the 3.5L V8. This assembly mounts in-line between...

Washer Jet Tubing is the flexible hose used within the windscreen washer system, supplied in 1 m lengths. It carries washer fluid from the reservo...

Bleed Screw - Metric is the bleed nipple for a disc brake caliper. Threaded into the caliper body, it is opened during brake bleeding to release t...

Spring plate

Handbrake Locking Plate for the rod-operated transmission handbrake - the drum-type parking brake mounted at the transfer gearbox output. The plat...

Screw M6 x 20 pan-head screw. It can be used in place of LR083229 (RYG500650 / DYP500210 / EYG50080) but is not identical: this screw has no capti...

Hazard Flasher Relay - the switching relay in the hazard warning circuit. When the hazard switch is operated, the flasher relay pulses all four di...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Exhaust Spacer Tube is a short pipe section within the exhaust system. It spaces and connects adjacent exhaust sections at a flanged joint, settin...

Brake T-Piece - Metric is a three-way junction in the brake hydraulic circuit. It joins three brake pipes at a single union, typically distributin...

Gasket for transfer box gearchange lever housing plate LT230 with LT85, LT77, Chrysler 3-speed or ZF 4-speed automatic. Also part of gasket kit RTC...

Plenum Hose - Breather T-Piece to Plenum

Flame Trap Hose forming part of the crankcase ventilation (breather) system on the V8 EFI petrol engine. It connects the flame trap T-piece to the...

Turbo Oil Drain Gasket seals the turbocharger oil return on the 2.5L 300TDi. Fitted at the joint between the turbocharger oil drain (return) pipe ...

Front cover gasket 200tdi Discovery/RR

Core Plug for the V8 petrol cylinder block and inlet manifold. The cup-type plug seals the casting core holes left in the coolant jacket after man...

Oil Seal for the front output shaft of the LT95 gearbox, sealing the transfer case around the rotating output shaft. The LT95 is a combined main g...

Grommet - a rubber panel grommet providing a sealed, protected pass-through for the choke cable and windscreen washer tubing. Fitted into the pane...

Core Plug for the cylinder head, sealing a core hole left in the casting during manufacture. It closes the opening left by the casting sand core a...

Water Pump for the Rover V8 EFI petrol engine, supplied with gasket. The water pump sits in the engine cooling circuit and is belt-driven from the...

Brake Caliper for the rear braking assembly, mounted on the left-hand side. The caliper houses the piston and hydraulic fluid inlet, converting pr...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Relay, a 70A 4-pin grey mini power relay. It provides high-current make-and-break switching for a heavy electrical load, letting a low-current con...

Drive Belt Idler Pulley for the auxiliary (serpentine) drive belt system of the V8 petrol engine. The idler guides the belt and maintains its runni...

Gasket & Seal Kit for the LT77 5-speed manual gearbox, supplying the gaskets and seals required when servicing or rebuilding the gearbox.

Rear Brake Caliper for the left-hand side of the rear axle, part of the hydraulic braking circuit. The caliper carries the hydraulic pistons that ...

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

Front Axle Drive Shaft transmits drive from the front differential to the right-hand wheel hub, forming part of the front axle drive shaft and hub ...

Front Crankshaft Oil Seal installed in the front cover assembly, part of the engine's crankshaft sealing arrangement. Seals the running clearance ...

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Headlamp Rim is the outer trim bezel that surrounds and retains the headlamp unit in the front panel, finished in chrome. It locates over the head...

Needle Roller Bearing for the front axle swivel pin housing. The bearing seats in the swivel housing bore and carries the stub axle, providing rad...

Split Pin used on a front-axle assembly to lock a castellated nut. The pin passes through the drilled fastener and the slots of the nut, and its le...

Water Pump for the Rover V8 petrol engine, of the viscous-drive type. It mounts to the front of the engine and forms part of the engine cooling cir...

Heater Outlet Hose is the coolant return hose from the heater matrix in the cabin heating circuit. It carries coolant from the outlet side of the ...

kit parts fixing headlamp

Set Screw, a hexagon-head metric fastener, M10 x 25mm. In Land Rover terminology a set screw is a bolt threaded along its full length rather than ...

Brake Disc - Solid - Front is the front brake disc, mounting to the wheel hub and providing the friction surface the brake pads clamp against durin...

Thermostat Housing Gasket for the 200TDi 2.5L turbo-diesel engine, sealing the thermostat housing to the cylinder head within the engine cooling ci...

Interior Door Handle for the right-hand side. Part of the door latch and release mechanism. Mounted on the inner door, the handle operates the lat...

Window Regulator Motor - RH is the electric drive motor for the right-hand window regulator assembly. It mounts directly to the window regulator m...

Aluminium Sealing Washer is a soft metal crush washer fitted under a threaded plug or fitting to form a leak-tight joint. When the bolt or plug is...