Range Rover Parts

Coolant Hose for the V8 carburettor petrol engine cooling circuit. It carries engine coolant between components of the cooling system, moulded to s...

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Amber Switch Bulb for the heated windscreen and auxiliary switches. This small bulb provides the amber illumination within the switch, lighting th...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Key Fob Cover Kit provides a replacement outer cover for the remote key fob, renewing a housing that has become worn, cracked or faded. It restore...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Glovebox Lock Set secures the glovebox lid in the closed position and is released by key. It mounts in the glovebox within the facia, forming part ...

Outside door release cable handle to latch RH/LH

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Self-Tapping Screw - an exterior body trim fastener. It secures the protective rubbing strip (side moulding) to the rear quarter panel, cutting it...

Locking Washer of the Starlock (shakeproof) type, a push-on retainer used to hold a component onto a plain shaft or to lock a fastener against vibr...

Window regulator front RH

Non-Return Valve for the V8 petrol engine, fitted to the inlet manifold vacuum take-off. The valve allows air to be drawn one way from the vacuum ...

Circlip - LT77 Selector Shaft for the LT77 5-speed manual gearbox. This circlip retains the selector shaft within the gear selector and shaft asse...

Decal name plate

Bolt - M6 x 30mm is a metric threaded fastener with a 6 mm nominal thread diameter and a 30 mm shank length. It secures bolted joints where an M6 ...

Locking Wheel Nut Key – Code A. Removal key for code-A locking wheel nuts. The key code is stamped on the original key and cannot be derived from t...

Clip is a retaining clip in the front windscreen wiper linkage. It secures the wiper motor and linkage assembly, holding the linkage components to...

Lithium-Ion Battery - the backup battery for the Telematics Control Unit (TCU). It supplies backup power to the telematics control unit so the uni...

Warning Label A warning label relating to the battery negative (earth) cable connection. It is applied in the vehicle to convey a safety instructi...

Washer - a general-purpose fixing washer used across multiple body, brake and chassis assemblies. It spreads the clamping load of a bolt or nut ov...

Torx Screw - 4.8 × 25mm for use in Land Rover body and trim assemblies. A metric Torx-head screw, 4.8mm diameter × 25mm length, for use where Torx...

Rear Side Door Channel is a glass run channel mounted within the rear side door, fitted to the right-hand (RH) side. The channel locates and guide...

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Sedimentor O-Ring for the diesel fuel filter assembly. This rubber sealing ring seals the sedimentor bowl against the filter head, preventing fuel...

Clip - a retaining clip used to secure finisher mouldings and column shroud panels to their supporting structure. It locates and holds the mouldin...

Retaining Clip for the front door lock, also known as the door lock plate.

Air Deflector for the carburettor air intake on the 3.5L V8 carburettor engine. Part of the heated-air intake arrangement, it directs warmed air t...

Core Plug - Cylinder Block Expansion Port is a pressed-steel sealing plug installed in the outer face of the cylinder block to close the casting ap...

Gasket - Front Cover for the VM Motori 2.5L Turbo Diesel engine. This gasket seals the engine front cover to the cylinder block face, providing an...

Bolt for the adjustable rear suspension arm on the Freelander 2 and Range Rover Evoque. This M14 × 85mm special bolt secures the adjustable rear a...

Decal - ZF Automatic Gearbox is an adhesive identification label associated with the ZF automatic transmission, located in the centre console and c...

Interior Trim Fixing Clip used within body and interior trim assemblies. This clip secures trim panels, insulation sections, ducting, and fascia c...

Gearbox Filter Plug for the LT77 five-speed manual gearbox. The plug closes the bore in the extension case that gives access to the gearbox oil fil...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Rubber Buffer

Oil Filter is the replaceable element in the engine lubrication circuit, capturing wear particles and combustion contaminants from the oil before i...

Windscreen wiper arm forming part of the windscreen wiper system. The arm transmits motion from the wiper linkage spindle to the wiper blade, main...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Torque Converter Housing Cover Gasket for the automatic transmission bell housing. It seals the lower access cover on the torque converter housing...

Seal Washer - Turbocharger Copper sealing washer for the turbocharger oil feed circuit. It seals the banjo union on the turbocharger's oil supply ...

Accelerator Cable for the Range Rover Classic 3.5L V8 carburettor engine, left-hand drive, manual transmission. This cable connects the accelerato...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Crankshaft Bolt is the retaining bolt that secures the pulley and damper assembly to the nose of the crankshaft on the V8 petrol engine. Threaded ...

Cable Tie for securing wiring looms and cables in Land Rover applications.

Screw - a No. 10 x 1" pan-head self-tapping screw used across interior and door assemblies. It secures the window regulator and door glass channel...