Range Rover Parts

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Grommet - rubber sealing grommet, 3/4 inch overall diameter with 1/8 inch centre hole. Used to seal and protect wiring cables where they pass thro...

Thermostat regulates coolant flow within the engine cooling circuit of the 2.5L 4-cylinder VM Turbo Diesel. Housed in the thermostat housing at th...

Exhaust Bracket for the exhaust mounting system. This bracket supports the exhaust line at the section immediately behind the front silencer, loca...

Rivet is a body fixing used to secure sheet-metal panels, wheelarch liners and trim to the vehicle structure. It forms a permanent, vibration-resi...

Non-Return Valve for the V8 petrol engine, fitted to the inlet manifold vacuum take-off. The valve allows air to be drawn one way from the vacuum ...

Clevis pin

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

Heater Bypass Coolant Valve for V8 petrol applications. This vacuum-operated valve is installed in the HVAC coolant circuit and controls the flow ...

Locking Wheel Nut Set for alloy wheels that use the original alloy wheel nuts, securing the road wheels against theft. The set includes 5 locking ...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Nutsert - 5/16" UNF is a blind rivet nut (rivnut) with a 5/16" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal ...

Torsion Spring Sleeve for the lower tailgate. It fits over the tailgate torsion spring, forming a protective bearing sleeve at the pivot and preven...

Clutch Cap that closes an aperture in the clutch bellhousing around the release mechanism. Fitted over an opening in the bellhousing, the cap seal...

Filler and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

Swivel Pin Retaining Bolt A fixing bolt for the front axle swivel pin housing. It secures a swivel pin to the swivel pin housing, retaining the pi...

Engine Stud for the Rover V8 petrol engine, measuring 5/16" x 2-1/8" with a UNC/UNF dual thread form. The coarse UNC end threads into the engine c...

Sealing Washer is a copper joint washer used in multiple engine and ancillary applications across the Land Rover range, including as a sealing wash...

Hose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...

Instrument Bulb Holder Assembly is a 1.4W instrument panel bulb supplied complete with its integrated holder, forming part of the instrument cluste...

Air Suspension Reservoir for the Electronic Air Suspension (EAS) system. This pressure vessel (accumulator) stores a reserve of compressed air, en...

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Land Rover Oval Name Badge - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground. Fitted to the front ...

Rear Crossmember is the rearmost transverse member of the vehicle chassis, closing and tying together the two main longitudinal chassis rails at th...

Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...

Air Cleaner Ring for the Range Rover L322 intake assembly. This sealing ring fits within the air cleaner housing on the BMW M62 B44 4.4-litre V8 p...

Wheel Centre Cap - set of four alloy wheel centre caps in Titan Silver. The centre cap clips into the hub bore of an alloy wheel, covering the hub...

Front Brake Caliper Repair Kit for front calipers used with vented discs. The kit supplies the piston seals needed to overhaul the front calipers....

Oval LAND ROVER Badge - gold lettering on a green background - for the tailgate. This is the classic oval "LAND ROVER" name badge fitted to the ex...

Rear Wiper Arm forms part of the rear screen (backlight) wiper assembly. It mounts onto the rear wiper motor spindle and carries the wiper blade a...

Brake pipe clip

Clip for exterior body trim and accessory fittings. The clip retains body mouldings, side steps, mudflaps and related exterior trim to the body, p...

Brake Light Switch - pedal-mounted stop lamp switch, located on the brake pedal box assembly. The switch mounts on the pedal bracket and is actuat...

Oil Cooler Gasket for the AJ-Series V8 petrol engine, sealing the oil cooler and filter housing to the cylinder block. This gasket forms the oil-t...

EGR Cooler Filter for the low-pressure exhaust gas recirculation circuit of the 2.0L I4 Ingenium diesel engine. The low-pressure EGR system draws ...

Washer Fluid Level Sensor for the windscreen washer system. The sensor fits into the washer fluid reservoir and monitors the volume of fluid remai...

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

Wiper Blade for the windscreen wiper system. The blade clips to the wiper arm and carries the rubber wiping element across the glass, clearing rai...

Wiper Blade - front windscreen wiper blade, part of the windscreen wiper and washer system. The blade attaches to the wiper arm and carries the ru...

Magnetic Oil Drain Plug for the engine oil sump on the 2.0L Ingenium (AJ200/AJ20) four-cylinder petrol and diesel engines. The plug seals the drai...

Oil Filter Gasket Kit for the engine oil filtration circuit of the 2.0L Ingenium (AJ200) engine, renewed with the oil filter element at each servic...

Wiper Arm is the windscreen wiper arm that carries the wiper blade across the windscreen. It mounts to the wiper linkage spindle and transfers the...

Coolant Hose forms part of the heater line within the engine cooling system, routing coolant between the engine and the heater matrix. Supplied co...

Water Outlet Connection (Upper) for the 4.4L DOHC V8 turbo-diesel (TDV8) engine. Part of the thermostat and coolant housing assembly, it carries co...

Tow Hook Protective Cap is a cover for the towing eye aperture in the bumper. It closes off the tow hook mounting point when not in use, keeping o...

Grommet is a sealing grommet fitted to the engine oil sump on V8 petrol engines. It seals the point where a tube or fitting passes through the sum...