Range Rover Sport L320 Parts

Spring Nut is an M10 "U"-type spring-steel clip nut that provides a captive threaded fixing point on panels and brackets. The U-shaped clip slides...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Oil Filter - the engine oil filter element for the 3.0L V6 turbo diesel (TD6) engine. Fitted in the engine lubrication circuit, the filter traps m...

Crossover Pipe Gasket for the exhaust system, sealing the joint between the exhaust crossover pipe and the exhaust manifold. On the 3.0L V6 (Gen2 ...

Front Axle Housing Oil Seal seats in the front axle case where the drive shaft passes through the housing to the hub. It runs against the rotating...

Propshaft Washer for the front propshaft flange connection. The washer sits at the bolted joint between the front propshaft and its mating flange,...

MAP Sensor (Manifold Absolute Pressure sensor) for the engine management system, mounted on the throttle housing. It measures the absolute pressur...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Rear Propshaft Bolt, securing the rear propshaft to the rear axle differential input flange within the rear driveline assembly. The bolt clamps th...

Transmission Oil Pan and Filter for the ZF 8HP 8-speed automatic transmission (8HP45 and 8HP70, and the later 8HP51/8HP76 variants). The pan bolts...

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Air Filter element for the engine air cleaner housing. Seated in the air cleaner housing upstream of the mass air flow sensor and throttle body, t...

Brake Light Switch - pedal-mounted stop lamp switch, located on the brake pedal box assembly. The switch mounts on the pedal bracket and is actuat...

Bolt with an external Torx head, M12 x 35 mm. Used to secure rear brake components at the disc and calliper mountings, and rear suspension fixings...

Coolant Expansion Tank Cap - pressurised filler cap for the coolant expansion and overflow container in the engine cooling system. The cap sets th...

Wheel Centre Cap - hub cover for modular steel road wheels. It press-fits into the centre bore of the wheel, covering the hub flange and keeping d...

Camshaft Screw for the cylinder head and camshaft assembly of the 3.0-litre TDV6 diesel engine. This is a manufacturer-specification retaining scr...

Front Brake Disc, internally vented, for the front braking system. The disc mounts to the front hub and provides the friction surface acted on by ...

Drain Plug Washer for the transfer box drain and level plugs. The washer seals the plug against the transfer box casing and is replaced each time ...

Catalyst Gasket for the exhaust system of the 2.0L 16V Ti-VCT four-cylinder petrol engine. This gasket seals the joint at the catalytic converter ...

Oil Drain Plug for the ZF transfer box housing. The plug closes the drain and fill port in the transfer box casing, and is removed to drain and re...

Oil Pump Seal for the V6 diesel engine oil pump assembly, part of the engine lubrication circuit. It seals the oil pump interface to prevent oil l...

Exhaust Crossover Pipe carries exhaust gas between the two cylinder banks of the 3.0 V6 diesel engine, routing the outlet of one manifold across th...

Micro Relay is a 20 amp, 4-pin switching relay used within the vehicle electrical system to control a high-current circuit from a low-current signa...

Front Brake Caliper Pin Kit covering both front calipers (left and right). The kit supplies the guide pin hardware required when servicing the fro...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Exhaust Manifold Gasket - Right-Hand for the 3.0L TDV6 and SDV6 diesel engine, sealing the right-hand cylinder bank's exhaust manifold to the front...

Key Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...

Locking Wheel Nuts Land Rover Discovery 3 Discovery 4 Range Rover 2002 - 2013 Rover Sport 2005 - 2014

Exhaust Manifold Gasket - Turbo to Manifold for the turbocharger and exhaust manifold assembly on the 3.0L TDV6 V6 diesel engine. This gasket seal...

Water Outlet Connection for the engine cooling system, forming a coolant outlet from the engine. The connection provides the port and hose union t...

Exhaust Manifold Nut is an M8 flanged hex nut that secures the exhaust manifold and turbocharger mounting flanges to the cylinder head. The copper...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Oil Separator Pipe for the 3.0L V6 diesel engine, forming part of the crankcase emission control (crankcase ventilation) system. It carries blow-b...

Exhaust Manifold Stud secures the exhaust manifold flange to the cylinder head within the exhaust assembly. This is a double-ended stud, threaded ...

o-ring oil cooler 3,0 TDV6

Camshaft Seal for the TDV6 2.7L V6 diesel engine. Seals the camshaft at its exit point from the cylinder head, preventing oil leakage from the cams...

Front Suspension Bolt - a mounting bolt used in the front suspension assembly, at the suspension arm and knuckle/hub mountings. It secures the joi...

Oil Pump for the engine lubrication system. Driven by the engine, it draws oil from the sump and delivers it under pressure through the oil galler...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...