Range Rover Sport L494 Parts

Wheel Centre Cap - a black alloy-wheel centre cap carrying the Land Rover oval in green and silver. It presses into the centre bore of an alloy wh...

24v dsl long belt

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Key Fob Cover Kit provides a replacement outer cover for the remote key fob, renewing a housing that has become worn, cracked or faded. It restore...

Wheel Centre Cap - set of four alloy wheel centre caps in Titan Silver. The centre cap clips into the hub bore of an alloy wheel, covering the hub...

Air Filter element for the engine air cleaner assembly. The filter sits inside the air cleaner housing and cleans the intake air before it passes ...

Coolant Hose forms part of the heater line within the engine cooling system, routing coolant between the engine and the heater matrix. Supplied co...

Oil Pump for the 2.7L and 3.0L V6 diesel (Lion) engine, operating within the lubrication circuit as part of the oil pump and sump assembly. Driven...

Catalyst Gasket for the exhaust system of the 2.0L 16V Ti-VCT four-cylinder petrol engine. This gasket seals the joint at the catalytic converter ...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Coolant Outlet Connection is part of the engine cooling circuit, forming the sealed outlet junction where coolant leaves the engine on its way to t...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Oil Separator for the crankcase ventilation circuit of the 3.0L V6 Diesel engine. Mounted within the crankcase emission control system, the separa...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Wheel Centre Cover fits into the central hub bore of an alloy wheel, concealing the hub and wheel-mounting hardware behind a finished cap that clip...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Oil Filter - the engine oil filter element for the 3.0L V6 turbo diesel (TD6) engine. Fitted in the engine lubrication circuit, the filter traps m...

Oil Separator Pipe for the 3.0L V6 diesel engine, forming part of the crankcase emission control (crankcase ventilation) system. It carries blow-b...

Camshaft Cover Gasket - sealing gasket between the camshaft cover and the cylinder head face, for 2.7L Td6 and 3.0L V6 diesel engines. The gasket ...

Oil Pump Gasket that seals the oil pump to the cylinder block within the engine lubrication system, for the 3.0L V6 diesel engine. It maintains th...

Water Inlet Tube for the engine coolant circuit of the 5.0L V8 petrol engine (AJ133). The tube carries coolant to the thermostat and its housing, ...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Hex Flange Nut, an M8 flanged nut used to secure the exhaust manifold and turbocharger fixings on V6 and V8 diesel engines. The integrated flange ...

Vacuum Pump Gasket sealing the vacuum pump to the engine. Forms the joint between the vacuum pump and its mounting face, maintaining the seal for ...

Injector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...

Dual-Tone Electric Horn producing a combined high and low note, part of the vehicle's audible warning system. Supplied with its mounting bracket.

Oil Level Sensor Lead - the wiring lead for the engine oil level sensor. It connects the oil level sensor at the oil pan to the vehicle wiring, ca...

Accessory Drive Belt - multi-rib belt driving the engine's front-end accessories. Transmits crankshaft rotation to the belt-driven ancillaries wit...

Brake Pad Wear Wire - front brake pad wear warning wire within the braking system. Routed to the front brake pad, the wire completes a circuit tha...

Timing Chain Tensioner Arm bears against the timing chain within the timing drive assembly, providing the face through which the tensioner applies ...

Hex Head Bolt - M14 x 148mm fastener used at the front crossmember and stabiliser bar, front suspension arm, rear bumper and tow bar mountings. A ...

Wiper Blade for the windscreen wiper assembly. The blade fits onto the wiper arm and sweeps the windscreen to clear rain and road spray, maintaini...

Lithium-Ion Battery - the backup battery for the Telematics Control Unit (TCU). It supplies backup power to the telematics control unit so the uni...

Side step insulator - a moulded pad that sits between the side step mounting bracket and the vehicle body, within the deployable side step mounting...

Brake Light Switch - pedal-mounted stop lamp switch, located on the brake pedal box assembly. The switch mounts on the pedal bracket and is actuat...

Asy Lamp

Gasket - Exhaust Pipe

Gearbox Plug

Primary Accessory Drive Belt for the 5.0L AJ133 supercharged V8 petrol engine, forming part of the front end accessory drive. The multi-ribbed ser...

Bolt for the camshaft timing gear, part of the Ingenium engine timing drive. It retains the timing sprocket to the camshaft, transferring drive fr...

Coolant Vent Hose - connects the engine vent elbow to the radiator, within the vent (bleed) circuit of the engine cooling system. The hose carries...