Land Rover Parts

Manifold Absolute Pressure (MAP) Sensor for the 3.0L V6 diesel engine, mounted in the throttle housing. It measures absolute pressure in the intake...

Oil Cooler, part of the engine lubrication system. It draws heat out of the engine oil to hold oil temperature within its operating range under su...

Valve Stem Seal seals the valve stem where it passes through the valve guide in the cylinder head of Ingenium diesel engines. Fitted over the top ...

O-Ring sealing a turbocharger oil and coolant connection within the turbocharger lubrication and cooling circuit. It seals the union at the turboc...

Cylinder Head Gasket seals the cylinder head to the engine block on the 2.0L Ingenium four-cylinder diesel engine (AJ200 series). It seals the com...

Crossover Pipe Gasket for the exhaust system, sealing the joint between the exhaust crossover pipe and the exhaust manifold. On the 3.0L V6 (Gen2 ...

Tyre Pressure Sensor (TPMS) for the direct tyre pressure monitoring system. Fitted at the wheel valve inside the tyre, it measures tyre pressure an...

Fuel Pump Drive Belt Kit for the rear accessory drive of the 3.0L V6 diesel engine. The belt transmits drive to the high-pressure fuel injection p...

Transmission Oil Pan for the ZF 8HP eight-speed automatic transmission. It bolts to the underside of the transmission case and retains the automati...

Gasket - Turbocharger Cooling

Steering Gear Connecting Rod is a steering linkage rod connecting the steering gear to the wheel-end steering arm. It transfers steering movement ...

Climate Control Humidity Sensor, an input device for the automatic climate control system. Mounted at the base of the interior rear-view mirror, i...

Evaporator for the heating, ventilation and air conditioning (HVAC) system, mounted within the heater assembly (main unit). Refrigerant expands and...

Bolt is a chassis fastener securing the front and rear crossmember and stabiliser (anti-roll) bar mountings. Supplied individually.

O-Ring seal for the automatic transmission oil cooler circuit (ZF 8-speed, 8HP). The O-ring seals a connection in the transmission fluid cooling c...

O-Ring seal for the automatic transmission oil cooler circuit (ZF 8-speed, 8HP). The O-ring seals a connection in the transmission fluid cooling c...

Front Brake Disc for the front axle, matched to the size-19 front brake configuration. It mounts to the front wheel hub and rotates with the wheel...

Torque Converter Screw for the automatic transmission drive coupling. This fixing secures the torque converter to the drive plate, transmitting en...

Fuel Injector Refit Kit - the seals and retainer required when removing and refitting a fuel injector on 3.0L V6 and 5.0L V8 supercharged petrol en...

Trim Clip - push-fit fastener securing exterior body mouldings, front and rear bumper trim and the radiator grille to the body panels. Renews an o...

Plastic Rivet is a push-fit fastener that secures front engine-compartment insulation panels to the body. It locates into a pre-formed panel hole t...

EGR Gasket Inlet

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Thermostat Housing Gasket seals the joint between the thermostat housing (water outlet) and the cylinder head within the cooling system. It mainta...

Exhaust Manifold Gasket - Right-Hand for the 3.0L TDV6 and SDV6 diesel engine, sealing the right-hand cylinder bank's exhaust manifold to the front...

Head Gasket - 3.0 TDV6 - Grade 3

Oil Level Sensor - electronic engine oil level sensor mounted in the wall of the sump, forming part of the engine lubrication monitoring circuit. ...

Crankshaft Front Oil Seal seals the front of the crankshaft where it passes through the timing cover, behind the crankshaft pulley. It retains eng...

Turbocharger Circlip - retaining clip for the turbocharger actuator on diesel turbocharger installations. It secures the actuator rod to the contr...

Trim Clip that secures interior and exterior trim panels, door finishers and mouldings to the body. The clip locates in a pre-formed panel apertur...

Gasket

Fuel Injection Pump Bolt secures the high-pressure fuel injection pump to its mounting on the engine. It provides the clamping load that holds the...

EGR Valve & Gasket - 2.2 TD4

Electronic Pressure Control Solenoid for the transfer case control circuit. The solenoid is actuated electrically by the vehicle's control module ...

Drive Fastener - black plastic drive-in retaining clip used to secure body mouldings, trim panels and interior finishers to their mounting panels. ...

Service Kit - L405 - 3.0 V6 Die & RRS - 3.0 V6 Die - EA000001 On

Piston - 0.50 mm Oversize for the 2.0-litre Ingenium (AJ200D / 204DTD) diesel engine. An engine-rebuild piston machined 0.50 mm over the standard ...

Front Brake Pad Set - friction pads for the front axle braking system. Ceramic-based pads that clamp against the front brake discs under caliper p...

Front Brake Pad Set - the friction pads for the front-axle disc brakes. The pads sit in the caliper and are clamped against the brake disc by the c...

Hood Latch for the bonnet closing mechanism. The latch is body-mounted and engages the bonnet striker to hold the bonnet shut, releasing when the ...

Bolt - Exhaust Manifold & EGR - a fixing bolt used in the exhaust manifold and exhaust gas recirculation (EGR) assembly of the TDV6/TDV8 diesel...