Land Rover Parts

Negative Battery Cable forms part of the vehicle's electrical earthing circuit. It connects the battery negative terminal to the vehicle earth poi...

Intermediate Exhaust Silencer with Catalyst - the centre section of the exhaust system on 4.0L and 4.6L V8 petrol applications. It sits between th...

Needle Roller Bearing for the manual gearbox mainshaft. The bearing carries a constant-mesh mainshaft gear, letting it spin freely on the mainshaf...

Distributor Drive Gear - V8

O-Ring for the battery compartment lid of the Range Rover P38 remote key fob. This small rubber seal sits in the groove around the battery cover, ...

O-Ring sealing the dipstick tube where it enters the cylinder block on the V8 petrol engine. Fitted around the lower end of the dipstick tube, thi...

Front Brake Caliper Slider Pin Dust Cover Kit. This kit supplies the rubber boots that protect the front brake caliper guide pins (slide pins) fro...

Locking Wheel Nut Key - Code C for removing locking wheel nuts with the Code C drive profile. The key engages the unique recessed socket of the Co...

Wheel Spacer Set - 30mm - Black - a set of four black finished aluminium alloy spacers for 5x120 PCD hubs, fitted between the hub face and the whee...

Locking Washer

Dowel used for the precise location and alignment of the front cover to the cylinder block on Rover V8 engines. These dowels ensure the front cove...

Rear Mudflap Kit for the twin-exhaust configuration, mounting behind the rear wheels to deflect mud, water and road debris away from the bodywork a...

Key Fob Battery for the remote-locking key fob, part of the central locking and alarm remote system. This is a CR2025 3V lithium coin cell. It pow...

Front Mudflap Kit mounts behind the front wheels at the lower edge of the body, deflecting road spray, mud and stones thrown up by the tyres away f...

Clutch Kit for the 2.5L 6-cylinder BMW diesel engine in the Range Rover P38, manual transmission only. This kit provides the friction assembly use...

Inlet Manifold O-Ring for the 2.5L 6-cylinder BMW diesel engine (M51). This O-ring seals the joint at the inlet manifold, preventing air ingress t...

Locking Wheel Nut Key - Code F for removing locking wheel nuts with the Code F drive profile, fitted to alloy wheels across the Defender, Discovery...

Front Constant Velocity (CV) Joint for the front axle drive shaft. The CV joint transmits drive from the front axle to the road wheel while allowi...

O-Ring for the 6mm air pipe in the electronic air suspension system, used in the air pipe harness that routes pressurised air between the compresso...

Air Suspension Compressor Filter for the Electronic Air Suspension (EAS) system — the inlet filter on the air compressor intake. The filter cleans...

Gearbox Sump Gasket for the ZF 4-speed automatic transmission, sealing the joint between the transmission oil pan (sump) and the gearbox casing. T...

Oil Pump for the R380 manual gearbox. Mounted at the rear of the gearbox and driven from the output shaft, the pump circulates gearbox oil to lubr...

Crankshaft Main Bearing Cap Cross-Bolt Seal Washer for the Rover V8 petrol engine. This 19mm diameter seal washer seals the main bearing cap cross...

Fixing Screw used in the flywheel, drive plate and clutch assembly. It is one of the threaded fasteners securing the flywheel or automatic drive p...

Hose Clip is a worm-drive (Jubilee-type) clamp with a 20-30 mm clamping range. Tightened by a captive worm screw, it secures a flexible hose onto ...

Crankshaft Position Sensor monitors crankshaft speed and position on V8 EFi petrol engines with automatic transmission. Mounted at the flywheel re...

Taper Roller Bearing - Differential Pinion - Inner supports the drive pinion shaft within the differential crownwheel and pinion assembly. The inn...

Edge Clip - Door Lock Mechanism with various applications across Land Rover Series, Defender, Discovery 1, and Range Rover Classic models. This sp...

Hex Nut

Bolt - 3/8" UNC x 1-1/4" is a UNC hex head bolt used in the front axle assembly of Land Rover vehicles. Used to secure the track rod damper bracke...

Clip - a small retaining clip used within the transfer box differential lock linkage and at the handbrake lever and clutch master cylinder mounting...

U-Type Spring Nut for the fascia (dashboard) assembly and mounting brackets. Spring-steel clip-on nut that grips a panel edge to provide a captive...

Cylinder Block Seal is a 16mm sealing washer fitted to the cylinder block of the Rover V8 petrol engine, closing off a machined passage in the bloc...

Grommet is a sealing grommet fitted to the engine oil sump on V8 petrol engines. It seals the point where a tube or fitting passes through the sum...

Front Radius Arm Washer - plain flat washer used at the inner bushing position of the front radius arm on the Range Rover P38, installed between th...

Handbrake Gaiter in Dark Granite, part of the centre console trim. This gaiter fits around the base of the handbrake lever, concealing the lever me...

Decal - Bonnet - Basalt Edition for the Range Rover P38. This is the bonnet decal specific to the Range Rover P38 Basalt special edition. It repli...

Tailgate Latch Assembly is the lower tailgate latch mechanism, fitted at the centre of the lower tailgate. It secures the lower tailgate closed an...

Bonnet Latch Assembly for vehicles equipped with the anti-theft alarm system. This latch secures the bonnet in the closed position and incorporates...

Throttle Position Sensor (Potentiometer) for V8 petrol engines with Electronic Fuel Injection (EFI). Mounts on the throttle body and signals throt...

Engine Plug is a core (welch) plug that seals the casting holes in the engine. Fitted to the cylinder block, cylinder head water jacket and inlet ...

Oxygen Sensor (lambda sensor) for the V8 EFI petrol exhaust system on catalyst-equipped applications. It measures residual oxygen in the exhaust ga...

ABS Sensor Bush is a retaining bush used to locate the wheel speed sensor within its mounting point in the hub or axle assembly. The bush provides...

Inlet Valve for the cylinder head valvetrain of the Rover V8 petrol engine (3.5L, 3.9L, 4.0L and 4.6L variants). It seats in the cylinder head inl...

Gasket

Towing Jaw rated to 3.5 tonnes, part of the towing/pintle hitch assembly. It provides the jaw coupling for trailer and recovery towing, mounting t...

Coolant Temperature Sensor - Green for the engine cooling and fuel management circuit in the 3.9L and 4.0L V8 petrol engine. A thermistor-type sen...

Needle Roller Bearing for the R380 manual gearbox. It carries the reverse idler on the layshaft, allowing the gear to rotate with minimal friction ...