Land Rover Parts

Towbar Harness for the vehicle towing electrical circuit. It connects the trailer towing socket into the vehicle wiring, providing the electrical ...

Cylinder Head Dowel for the V8 petrol engine. The dowel is a locating pin fitted to the cylinder block deck that positively registers the cylinder ...

Differential Cross Shaft for the Land Rover-type differential. The cross shaft locates through the differential case and carries the two differenti...

Special Bolt

Transmission Selector Switch reports the selected gear position on the ZF 4-speed automatic gearbox, signalling the lever range to the transmission...

Radiator Top Hose for the engine cooling circuit. It carries hot coolant from the engine outlet to the top inlet of the radiator, where heat is dis...

Headlamp assy LH

Differential Thrust Washer for the four-pinion differential in the Land Rover-type axle. Seats behind a differential gear to control end-float and...

Accelerator Return Spring for the throttle linkage on V8 EFI petrol engines. Returns the throttle to the closed position when the accelerator is r...

Track Rod Flange Nut secures the track rod end within the steering linkage. The integral flange spreads the clamping load across the joint face, r...

Front Indicator Lamp for the front exterior lighting assembly, mounted on the left-hand side of the vehicle. The lamp provides front direction-ind...

Vacuum Advance Unit for the ignition distributor on the 3.5L V8 petrol engine. This vacuum capsule mounts on the side of the distributor and conne...

Front Shock Absorber for the front suspension, fitted between the front axle and the chassis to damp spring oscillation and control wheel movement ...

Locking Wheel Nut Key - Code H, the keyed adaptor that engages the splined pattern of Code H locking wheel nuts. The key is placed over the lockin...

Locking Wheel Nut Key - Code E, the keyed adaptor that engages the splined pattern of Code E locking wheel nuts. The key is placed over the lockin...

Steel Road Wheel - 8 x 16 pressed-steel wheel in the modular pattern, finished in black, ET25 offset. The pressed-steel construction withstands of...

Terrafirma 30mm alloy wheel spacers complete with high tensile studs and a complete set of retaining nuts 5x120 PCD. (Set of 4)

Side Steps with Mudflaps are a bolt-on exterior accessory fitted along the lower body sides, supplied as a matched left-and-right pair. Each step ...

Rear Mudflap Kit mounts behind the rear wheels at the lower edge of the body, deflecting road spray, mud and stones thrown up by the tyres away fro...

Mud Flap for the rear wheel arch, right-hand side. Fitted behind the rear wheel at the lower body, the flap deflects road spray, mud and stone deb...

Portable Jump Starter and Air Compressor - a handheld 12V power pack combining a battery jump starter, power bank, tyre inflator and LED work light...

Carburettor Float for the SU carburettor float chamber, within the fuel metering circuit of the 3.5L V8 twin-carburettor petrol engine. The float ...

Gearbox Extension Case Screw for the R380 5-speed manual gearbox. M5 × 30 Torx head screw used to secure the extension case on the R380 gearbox. T...

Gearbox Bearing for the R380 5-speed manual gearbox, measuring 35 × 72 mm. Fitted within the R380 transmission assembly, this rolling-element bear...

Air to Coil Conversion Kit - Medium Load 1" Lift replaces the electronically controlled air spring suspension with conventional coil springs, remov...

Clip - retaining for rubbing strip - rear quarter

Drive Belt for the accessory belt drive, a poly-V (multi-ribbed) belt that transmits drive from the crankshaft pulley to the air conditioning compr...

Fuel Tank Inspection Plate Seal is a rubber sealing gasket for the fuel tank inspection plate in the fuel tank assembly. The inspection plate prov...

Sealing Washer - 18 mm OD x 12 mm ID is a sealing washer with a 12 mm inner diameter and an 18 mm outer diameter, used to seal threaded unions and ...

Cylinder Head Bolt Kit is a complete set of the bolts that clamp the cylinder head to the engine block. The kit comprises 14 Torx-drive cylinder h...

Vacuum Advance Unit for the ignition distributor on the 3.5L V8 petrol engine. This vacuum capsule mounts on the side of the distributor and conne...

Reverse Idler Shaft for the R380 5-speed manual gearbox. The shaft carries the reverse idler gear within the gearbox casing. The reverse idler gea...

Rear Lamp Assembly - LH is the left-hand rear lamp unit within the exterior rear lighting system. The assembly combines the rear fog and reversing...

Actuator