Land Rover Parts

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Taper Roller Bearing - the mainshaft bearing used in the LT77 and R380 five-speed manual gearboxes, located at the rear of the primary pinion where...

Rear Brake Caliper Seal Kit for rebuilding both rear brake calipers on the Discovery 2 and Range Rover P38, supplied as a pair to cover both sides ...

Pipe and Hose Retaining Clip - Engine is a small-bore clip used to retain pipes and hoses at multiple points across the engine bay and fuel system ...

Drive Shaft Oil Seal for the front and rear hub assemblies. This lip seal fits at the inboard end of the front and rear hub carriers, sealing axle...

Flange Bolt - M6 × 10mm is a metric flanged-head fastener used across a wide range of assembly points on Land Rover vehicles. The integrated flang...

Self-Tapping Screw - Black is an M8 x 25mm self-tapping screw with a black finish. The self-tapping thread cuts its own mating thread as it is dri...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Crown Wheel Bolt secures the crown wheel (ring gear) to the differential carrier within the axle differential. Threaded 3/8 UNF and 1.1/8 inch lon...

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Panhard Rod Bolt - M16 × 70mm flanged hexagonal head. This bolt secures the panhard rod at its mounting bracket, retaining the rod that locates th...

Rear Propshaft Coupling Kit - a flexible rubber coupling that connects the rear propeller shaft to the drive flange, transmitting drive while absor...

Cup Plug (core plug) for the front face of the Rover V8 cylinder head. This pressed-steel cup plug seals the front casting gallery in the Rover 3....

Locking Wheel Nut Key – Code A. Removal key for code-A locking wheel nuts. The key code is stamped on the original key and cannot be derived from t...

Self-Tapping Screw - an exterior body trim fastener. It secures the protective rubbing strip (side moulding) to the rear quarter panel, cutting it...

In-Tank Fuel Pump & Sender Unit for Range Rover P38A petrol applications. This combined assembly houses the electric fuel pump and fuel level s...

Front Brake Caliper for the right-hand side. The caliper straddles the front brake disc and houses the hydraulic pistons that force the brake pads ...

Differential Assembly - a reconditioned 4-pin differential unit for the Land Rover-type axle. The differential sits at the centre of the axle, tak...

Transfer Box Output Shaft Mud Shield fitted at the output shaft oil seal of the LT230 transfer box. The shield sits over the output shaft ahead of...

Taper Roller Bearing - outer pinion bearing in the differential final drive assembly. The drive pinion is carried on a pair of opposed taper rolle...

Bleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...

Drag Link Ball Joint (Short) is a steering linkage joint fitted at the short end of the drag link, within the steering track-rod circuit. It forms...

Breather Adaptor - a threaded fitting in the axle and transfer case ventilation (breather) system. It screws into the axle casing or transfer case...

Mainshaft Taper Roller Bearing supports the mainshaft at the 5th/reverse end of the R380 (and LT77) 5-speed manual gearbox. It carries the mainsha...

Flanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...

Clevis pin

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Brake Hose - Rear - flexible right-hand rear brake hose. It carries hydraulic pressure from the rigid chassis brake pipe across the suspension's m...

Brake Hose - Rear - flexible left-hand rear brake hose. It carries hydraulic pressure from the rigid chassis brake pipe across the suspension's mo...

Engine Mounting - rubber engine mount that supports the engine on the chassis mounting bracket. The bonded rubber element carries the static weight...

Washer Jet - twin-nozzle windscreen washer jet for the front wash/wipe system. It seats in the bonnet or scuttle panel and directs two fine sprays ...

Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...

Self-Tapping Screw - a No. 8 x 1/2" self-tapping screw used as a body-trim fixing. It secures body trim panel brackets, headlamp finisher panels a...

Bulb and Holder Assembly - Clear for dashboard and switch panel illumination. The assembly consists of a small bulb pre-fitted into a plastic hold...

Radiator Assembly for the Range Rover P38 cooling system, fitted to the 2.5L Diesel engine. The radiator dissipates heat from engine coolant circu...

Fuel Injector for the EFI V8 petrol engine, part of the multi-point electronic fuel injection system. The injector is an electrically-operated sol...

Bolt Threaded fastener used within the exhaust system assembly.

Bump Stop - rubber suspension bump stop for the Range Rover P38, fitted to limit suspension travel at full compression and absorb the final impact ...

Coolant Hose connects the heater circuit to the thermostat housing, routing coolant between the heater matrix feed and the thermostat within the co...

Coolant Hose carries coolant through the engine bypass circuit, connecting the bypass outlet to the thermostat housing. It is the upper hose in th...

Wiper Blade for the front windscreen wash/wipe system, for left-hand drive applications. Fits the wiper arm clip and sweeps the windscreen in LHD ...

COIL IGNITION GEMS (bobineblok RR 4.6 V8) INTERMOTOR

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...

Brake lever kit