Land Rover Parts

Lock Barrel & Key Set for the door locks. This set contains two lock barrels and two keys, supplied without a steering column lock. For the an...

Plenum Inlet Gasket seals the joint between the upper plenum chamber and the lower inlet manifold on the EFI Rover V8 engine. It forms the air-tig...

Oil Filter Rotor is the rotating element of the centrifugal oil filter on the Td5 2.5L 5-cylinder turbo diesel engine. Mounted within the centrifu...

Coolant Bypass Hose for the thermostat assembly on the 3.5L V8 petrol engine. This hose connects the thermostat housing to the inlet manifold, pro...

Rocker cover rubber washer petrol

Sliding Window Seal for the front door assembly. This rubber seal fits to the front face of the sliding side window, sealing the glass against the ...

Wiper Motor for the windscreen wiper assembly. It converts the electrical supply into rotary motion, driving the wiper transmission and linkage th...

Wheel Bearing Kit - a complete single-hub kit containing the bearings, seal and fixings to rebuild one wheel hub, suitable for either a front or a ...

Detent Spring for the manual gearbox gear selector mechanism. The spring loads the detent ball against the selector shaft, holding the selected ge...

Steering damper installed within the steering linkage assembly to control lateral movement of the track rod and reduce vibration transmitted throug...

Oil Seal installed within the wheel hub assembly to retain lubricant and prevent contamination ingress at the hub-to-stub-axle interface. The seal...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Oil drain plug TD5

Track Rod Clamp is a split-tube collar that secures the threaded track rod end into the track rod tube on the front steering axle. Once the front ...

Spire Nut for body-panel fixings - a sprung spring-steel captive nut that clips over a panel edge or into a pierced hole to provide a threaded anch...

7" round LED headlamp 12/24V black 78W LHD (pair)

Headlamp for the front exterior lighting system, configured for left-hand-drive vehicles (right-hand traffic). The unit houses the halogen bulb an...

Front Door Hinge - Upper, Left-Hand - upper hinge for the front door, mounted between the door and the body aperture. It forms the upper pivot of ...

Bulb Holder - double-filament bulb holder for an exterior lamp assembly, accepting a 5/21W (P21/5W) twin-filament bulb. The holder seats into the ...

filter fuel inline Series petrol engines. Used as air filter in vacuum control lines for EGR in: - L322 3.0 M57 DSL (BMW) - Freelander1 M47 16V 2.0...

Toggle Switch is a two-position on/off switch in the dashboard switchgear, controlling the instrument and panel lighting circuit. The sprung toggl...

Fuel Pump Seal, part of the fuel delivery system at the in-tank fuel pump and sender module. Seals the joint where the fuel pump and sender unit m...

Windscreen Wiper Motor for the front wiper system, supplied as a motor assembly with the integral reduction gear and park switch. Supplied without ...

HOLDER - BULB - SINGLE POLE - D1/D2/DEF ALL/F1/P38

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Lock Washer for the gearbox mainshaft, securing the special retaining nut where the mainshaft meets the transfer box. A tab washer whose tang is b...

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the Rover V8 petrol engine. It forms a coolant-tight joint bet...

Hinge Pin Kit containing the replacement hardware for door and rear tailgate hinges on Series and early Defender models. Fits the front and rear d...

Brake shoe spring 109 rear lower

O-Ring - an elastomer seal used at the oil cooler pipe connection within the engine oil cooler circuit. It seats in the union between the oil cool...

Ancillary Drive Idler Pulley for the Td5 2.5L 5-Cylinder diesel engine. Located within the front-of-engine ancillary drive system, this pulley pro...

Alternator - charging unit in the vehicle's electrical charging system. Driven from the engine by the accessory belt, it generates current to powe...

Idler bracket and pulley TD5 non-ACE

Distributor Module for the 3.5L Rover V8 petrol engine, used with the earlier single-coil electronic ignition system. It forms part of the distribu...

Clutch Slave Cylinder Push Rod within the Clutch Actuation Assembly, transmitting hydraulic force from the external slave cylinder to the clutch re...

Carburettor Inlet Seal for the Zenith carburettor, in the engine air intake system. It seals the joint between the carburettor air intake and the ...

Transfer Lever Knob in red, for the high/low range selector on the transfer gearbox. It threads onto the top of the transfer change lever and prov...

Wiper Blade with a pin (bayonet) fitting for attachment to the wiper arm. Part of the windscreen wiper assembly, the blade holds the rubber wiping...

Rotor Arm for the Lucas distributor in the ignition system. Mounted on the distributor shaft beneath the cap, it routes the high-tension spark fro...

Self-Locking Nut with a 5/16" UNF thread and a 1/2" across-flats hexagon. The self-locking action resists loosening under vibration, retaining cla...

Gearbox Plug Sealing Washer for LT76 and LT77 manual gearbox drain, level, and inspection plugs. This sealing washer fits beneath the thread of ge...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Shim hinge

Weatherstrip for the alpine light (side roof window) glass. This rubber sealing strip retains and seals the 5mm glass panels of the alpine lights ...

Track Rod End for the steering linkage, with a left-hand thread. The track rod end forms the ball-jointed connection between the steering link and...

Exterior Mirror - Round Arm is a complete wing mirror assembly comprising a round convex mirror head and a standard-length mounting arm, designed f...

Exhaust Silencer sits in the rear section of the exhaust system, downstream of the intermediate pipe and ahead of the tailpipe outlet, where it for...

Inlet Manifold Seal for the V8 petrol induction system, straight pattern. The seal closes the joint between the underside of the inlet manifold an...