Land Rover Parts

Retaining Clip - a push-in trim retainer used to secure exterior mouldings and interior finisher panels. The nylon clip pushes into an 8 mm mounti...

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Injector Bolt for the 2.2L Td4 (Puma) diesel fuel injection system. The bolt retains a fuel injector in its bore in the cylinder head, clamping th...

Trim Clip - push-fit fastener securing exterior body mouldings, front and rear bumper trim and the radiator grille to the body panels. Renews an o...

Fan Coupling - the electronically controlled clutch that drives the engine cooling fan within the radiator cooling assembly. It mounts on the fan ...

Exhaust Gas Temperature Sensor measures the temperature of the exhaust stream within the diesel exhaust and emissions system. It reports to the en...

Brake Pad Set is a set of front disc brake friction pads for the front-axle braking assembly. The pads locate in the front brake calipers and are ...

Heater Cable Assembly for the heating and air conditioning control system. The cable links the dashboard heater control to the heater box, transmit...

Rear Hinge Bracket for the tailgate hinge assembly. The bracket mounts to the rear of the chassis frame and carries the tailgate hinge, locating t...

Exhaust Manifold Gasket - Right-Hand for the 3.0L TDV6 and SDV6 diesel engine, sealing the right-hand cylinder bank's exhaust manifold to the front...

Rocker Cover Gasket - Left Hand for the AJ V8 petrol engine. This gasket seals the rocker cover to the left-hand cylinder head, preventing oil from...

Rocker Cover Gasket - Right Hand for the AJ V8 petrol engine. This gasket seals the rocker cover to the right-hand cylinder head, preventing oil fr...

Floor Mat for the second-row (rear) floor area. It is shaped to fit the rear passenger footwell and protects the vehicle's carpet from mud, moistur...

Crankshaft Pulley Bolt - M12 x 80mm fastener that secures the crankshaft pulley (torsional vibration damper) to the front nose of the crankshaft on...

Anti-Roll Bar Link - Front for the front suspension of the Freelander 2 (2006-2014). This stabiliser link connects the front anti-roll bar to the ...

Crankshaft Position Sensor for the 2.2L TD4 common-rail direct-injection diesel engine. Mounted at the crankshaft, the sensor reads the reluctor (...

Timing Belt - 2.0 MPi is the camshaft drive belt for the 2.0L 4-cylinder MPi petrol engine, forming part of the valvetrain timing system. The belt...

Front Suspension Bolt - a mounting bolt used in the front suspension assembly, at the suspension arm and knuckle/hub mountings. It secures the joi...

Body Mount - To Chassis Frame is a rubber isolation mount positioned at one of the body-to-chassis attachment points. The mount cushions the body ...

Upper Engine Tie Bar forming the upper restraint in the engine mounting assembly. This tie bar connects the engine to the vehicle body at the uppe...

Clip retains the heater and air-conditioning control cable within the HVAC control assembly, holding the cable on its correct routing.

O-Ring for the manual air conditioning pipe and hose circuit. This O-ring seals connections within the manual air conditioning pipework, preventin...

Blower Motor for the heating and air conditioning system, left-hand drive (LHD) configuration. Electric motor and fan assembly that circulates air...

Brake Union - Blanking Plug, male thread, M10 x 1mm, short body. Used in the metric hydraulic brake circuit to blank off an unused or redundant po...

Front Seat Armrest Finisher, the decorative trim panel forming the visible outer surface of the front seat armrest on the Discovery 2. Applies to ...

Trim Clip - retaining clip for interior trim panels. Secures interior trim components such as the instrument panel, glove box and speaker surround...

Rear Door Finisher for the internal rear door release assembly. This trim panel finisher fits around the interior door release mechanism on the re...

Gear Lever Bias Plate for the manual gearbox gear change mechanism. It sits in the gear lever remote housing and works with the bias spring to load...

Gearchange Spring for the LT77 five-speed manual gearbox, fitted within the gearchange and lever assembly. The spring acts on the gear lever mecha...

Thrust Washer and Pin for the LT95 four-speed gearbox, 3.55mm thickness. This selective-thickness washer, with its locating pin, sets the end-float...

Interlock Retainer for the LT77 five-speed manual gearbox gearchange. It holds the selector interlock components within the selector and yoke assem...

Differential Pinion Bearing Shim - 0.068 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Differential Pinion Bearing Shim - 0.066 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Radiator Muff in black, by Exmoor Trim, for the classic Defender radiator protection system. This cover fits over the front grille and radiator on...

Radiator Mounting - Rubber is a rubber isolation bush used to secure and cushion the radiator within its mounting points. It absorbs vibration and...

Sealing Washer seals the turbocharger oil drain pipe where it meets its adaptor on the engine block. It forms an oil-tight joint in the turbocharg...

Camshaft for the Range Rover Classic fitted with the 4.2L V8 Petrol engine, as used in the LSE (Long Wheelbase Special Edition) from 1992 to 1994. ...

Crankshaft Damper for the 300TDi 2.5L turbo diesel engine, mounted on the front nose of the crankshaft. This torsional vibration damper absorbs th...

Oil Pump - 200Tdi is the engine-driven pump responsible for circulating pressurised oil throughout the lubrication system of the 200Tdi 2.5L direct...

Inlet Valve for the cylinder head valvetrain of the 200TDi 2.5L 4-cylinder turbo diesel engine. The valve seals against its seat in the cylinder h...

Nut - Plastic - 7mm is a captive plastic fastener for trim and body panel fixing. This plastic nut presses into a 7mm hole in the body or trim pan...