Land Rover Parts

Wiper Motor Rack for the front windscreen wash/wipe system, for left-hand drive applications. The rack transfers drive from the wiper motor to the...

Wiper Arm - Blade Assembly is the complete rear wiper arm and blade unit for the Discovery 3 and Discovery 4, fitted to the rear tailgate. The arm...

Heater Hose forming part of the engine cooling and cabin heating circuit. This hose connects within the heater circuit, routing coolant between th...

Rear End Door Seal seals the rear end door (tailgate) aperture against the surrounding body. This moulded rubber seal fits around the rear body ap...

Bolt - M6 x 55mm hex head bolt used in braking system assemblies. Standard metric hex fastener supplying clamping force in brake-related mounting ...

haynes manual Discovery 1 89>98 Petrol & Diesel (NOT MPI)

Air Suspension Pipe Collet for the ACE (Active Cornering Enhancement) system on the Discovery 2. Push-fit retaining clip that locks the air pipe s...

Reservoir bracket

Engine Mounting Rubber

Parts Catalogue is the parts reference for the Land Rover Series IIA, covering the bonneted control models. It sets out the part numbers for the v...

Truck Cab Waist Seal for the Land Rover Defender truck cab body variant. This rubber seal fits at the waist level of the truck cab body, sealing t...

Contact Set for the ignition distributor of the 3.5L V8 petrol engine. The contact breaker points open and close the primary circuit to the ignitio...

Self Tapping Screw for use in Land Rover body, chassis, and hardware applications.

Connecting Rod Bolt for the big-end of the connecting rod, part of the crankshaft and connecting rod assembly. The bolt clamps the big-end bearing...

Spring Clip for the rear end door trim casing, part of the interior trim fixings. The sprung clip retains the rear door card (trim casing) to the ...

Exhaust Plate for the intermediate section of the exhaust system on 88" Short Wheelbase variants in left-hand drive (LHD) configuration. This plat...

U-Bolt for clamping the front axle casing to the leaf spring, metric thread, round-bend profile. Three round-bend U-bolts are fitted per vehicle, ...

Fuel Filler Cap Seal for the fuel system of the Range Rover Classic. This rubber seal fits the hinged (flip-up) fuel filler cap and creates a fuel...

Starter Bush Kit - the set of bronze bushes that support the armature shaft of the inertia-type starter motor (Lucas Type 2M100) used on 4-cylinder...

Steering Valve Ring is a PTFE sealing ring used within the rotary valve of the Adwest power steering box. It seals between the pressure lands of t...

Diff Pinion Taper Roller Bearing is the inner pinion taper roller bearing in the Salisbury axle differential. It supports the pinion shaft where i...

Heater Matrix for the cabin heater assembly, mounted inside the heater box within the HVAC housing. Engine coolant is circulated through the matri...

Handbrake Tension Spring - the lower spring within the transmission (drum) handbrake assembly, fitted to vehicles with the LT95 four-speed gearbox....

Bleed Screw for the imperial-specification front and rear brake calipers on the Range Rover Classic. This imperial-thread bleed screw fits the cal...

Front Brake Caliper Piston is a 41mm piston that operates in the front brake caliper, part of the braking hydraulic circuit for solid disc brakes. ...

Front Brake Caliper Piston is a 41mm piston that operates in the front brake caliper, part of the braking hydraulic circuit for solid disc brakes. ...

Constant Velocity (CV) Joint for the front axle, in the non-ABS configuration. It sits at the outer end of the front halfshaft, within the swivel h...

Brake Master Cylinder Repair Kit for the single-circuit master cylinder and servo system on the Series 2 and Series 3 Land Rover. This repair kit ...

Valve Guide for the Rover V8 cylinder head. Pressed into the cylinder head, the guide supports the valve stem and keeps the valve concentric with ...

Rocker Cover Screw - Long for the Rover 3.5L V8 engine. This long 1/4" UNC x 1-5/16" screw secures the rocker cover to the cylinder head on the Ro...

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Gasket inspection cover

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Distributor Terminal Adaptor and Lead for the ignition system, part of the Distributor & Ignition assembly. This adaptor and short lead connec...

Choke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...

Fuel Filler Cap for the fuel tank filler neck, part of the Fuel Tank & Ancillaries assembly. This is the hinged flip-type cap, fitted with a b...

Centre Silencer for the V8 single exhaust system. This intermediate silencer sits between the front (down) pipe and the rear silencer, providing t...

Heater Hose - Series 3 RHD

Gearbox Crossmember for the chassis of long wheelbase Series Land Rovers. This steel crossmember spans the chassis rails beneath the gearbox, prov...

Light Socket for the inspection lamp on Series Land Rover vehicles. This black bayonet-type bulb holder is used in the inspection lamp assembly, p...

Ignition Switch for the steering-column lock, diesel specification. The switch is the electrical unit that fits into the steering-column lock barre...

Accelerator Cable for left-hand-drive applications, forming part of the throttle control linkage. The cable connects the accelerator pedal to the ...