Land Rover Parts

Rear Drum Brake Shoe Set covering one full axle, sized for 11-inch rear drum brakes. The shoes carry the friction linings that press outward agains...

Universal Joint for the axle half shaft, allowing the shaft to transmit drive through an angle. The joint sits within the half shaft and lets it t...

Ignition Coil for the ignition system of 4-cylinder petrol engines. The coil steps up the low-voltage supply into the high-tension output that fir...

Window Channel - Lower is the lower glass-run channel for the front door window. It runs along the bottom of the window aperture and guides the do...

Timing Belt Kit with Tensioners for the 300 TDi 2.5L turbo diesel engine. The kit serves the timing belt drive - the toothed-belt system that synch...

Fitment All TD5 diesel models up to (VIN) 6A999999 All TD5 diesel models All V8 EFi petrol models 2.5L 6 Cyl BMW Diesel /4.0L and 4.6L EFI V8 P...

Rear Fog Lamp forming part of the rear lighting assembly, providing a high-intensity red rear light for use in poor visibility. It operates on its...

Steering Relay Assembly within the steering linkage. The relay transfers steering movement from the steering box drop arm to the drag link, passin...

Nut, 1/2" UNF. A threaded fastener used on the early 4-cylinder diesel engine assembly.

Glow Plug for the 200TDi and 300TDi 2.5-litre direct-injection turbo diesel engines. It forms part of the cold-start pre-heating system. The glow ...

Wheel Cylinder for the rear drum brake assembly, left-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hyd...

Side Lamp - front side (parking) lamp in the exterior lighting system. Dome-type front side lamp providing position and marker lighting at the fro...

Restore your Series or Defender Land Rover's door with this door bottom repair section. This replacement piece is designed to repair damaged or rus...

Fuel Filler Cap Seal is the sealing ring fitted inside the metal fuel filler cap. It forms the seal between the cap and the filler neck, preventin...

Bolt - 3/8" BSF x 1" hexagonal head bolt to British Standard Fine thread specification. 3/8" BSF (British Standard Fine) thread with a 1" shank le...

Felt Washer for the output shaft assemblies of the LT230 transfer box. This washer is fitted at the front and rear output flanges of the LT230, wh...

Clutch Slave Cylinder for the hydraulic clutch release system on Defender and Discovery 2 models fitted with the R380 manual gearbox. Mounted on t...

Grease Nipple with a short thread, used at propshaft universal joint lubrication points. The nipple threads into the grease point and provides the...

Shock Absorber for the front suspension on the short-wheelbase (SWB) chassis. Mounted between the front axle and the chassis, the hydraulic damper...

Rear Upper Shock Absorber Bracket, the upper mounting bracket for the rear damper within the rear suspension. It forms the fixed upper anchorage b...

Captive Nut with a UNF thread, providing a fixed threaded anchor point for a bolted fixing. The nut is retained in its bracket or panel so it cann...

Vacuum Pump Gasket for the 2.5L 300TDi diesel engine, sealing the vacuum pump mounting face to the cylinder block. The vacuum pump is driven from ...

Brake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...

Rear Reverse Lamp - reversing lamp for the rear lighting assembly, providing white illumination to the rear when reverse gear is selected. It moun...

Cylinder Head Bolt securing the cylinder head to the cylinder block and clamping the head gasket joint. It maintains the clamping force that seals...

Brake pad kit rear

Shock Absorber Bush for the lower mounting of a suspension damper. The rubber bush seats in the shock absorber's lower mounting eye, locating the ...

Front Hub Lock Washer located within the Front Hub & Driveshaft Assembly, securing the hub bearing retaining nut in position. The lock washer ...

Hub Oil Seal - Inner for the front and rear wheel hubs, seating around the stub axle. The seal runs on the stub axle to retain hub lubricant and e...

Heater Hose - S Shape carries coolant from the engine to the heater matrix in the Series III cabin heating circuit. The hose has an S-shaped profi...

Lower Windscreen Seal for the Defender windscreen mounting assembly. This felt seal spans the full width of the lower windscreen channel, sealing ...

Elbow Gasket seals the coolant outlet elbow, or thermostat housing, to the inlet manifold on the V8 petrol engine, forming part of the engine cooli...

Front Shock Absorber, a hydraulic telescopic damper for the front suspension. It mounts between the front axle and the chassis and damps the oscill...

Timing Belt Tensioner for the 2.5L Td5 5-Cylinder Turbo Diesel engine timing system. The tensioner pulley bears directly against the timing belt a...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Exhaust Manifold Gasket for the 4.0L and 4.6L EFi V8 petrol engine. This twin-port gasket seals the exhaust manifold-to-cylinder head joint at two...

Differential Taper Roller Bearing for the axle differential assembly. It supports the differential carrier within the axle casing, carrying the com...

Speedometer Cable connects the speedometer drive on the gearbox to the speedometer head in the instrument cluster. The rotating inner cable transm...

Cylinder Head Dowel for the Td5 2.5L 5-cylinder turbo diesel engine. The dowel locates between the cylinder block and the cylinder head, aligning ...

Bolt - a threaded fastener used within the rear axle and suspension assembly. It secures the rear knuckle and suspension arm mountings, clamping e...

Bonnet Hinge Bolt Kit - a set of stainless steel fixings for mounting the bonnet hinges that allow the bonnet to pivot open. The kit secures the h...

Crankshaft Oil Seal Kit for a full rear crankshaft seal replacement on Series Land Rover engines with a 3-bearing crankshaft. This kit includes tw...

Wiper Switch - Column is the steering-column stalk switch that controls the windscreen wash/wipe function. Mounted on the steering column, it sele...

Upper Ball Joint for the front axle steering knuckle (swivel housing) assembly. The knuckle pivots on an upper and a lower ball joint; this upper ...

Fitment: All models to (VIN) KA930455 All models 1980 on

Cyclone Breather Filter for the crankcase ventilation system on the four-cylinder 2.5L diesel engine (naturally aspirated, 200TDi and 300TDi). Mou...

Gear Knob - gear lever knob for the R380 5-speed manual gearbox. Threads onto the gearchange lever, forming the driver's hand grip and gear-select...

Oil Pump Gasket for the Rover V8 petrol engine lubrication system. This gasket seals the oil pump to its mating face, maintaining oil pressure and...