Land Rover Parts

Brake Pipe – Rear Drum – Right is a pre-formed rigid pipe serving the right-hand rear drum brake. It carries hydraulic pressure to the rear drum a...

Radiator Top Hose - the upper radiator hose in the engine cooling circuit. It carries hot coolant from the engine outlet to the top of the radiato...

Exhaust Silencer - Twin Pipe for the Range Rover Classic V8 petrol twin pipe exhaust system, from chassis suffix F onwards. This rear silencer att...

M16 Hex Nut is a plain hexagonal fastening nut used across the towing and body hardware. It is most commonly used to secure the tow ball to the to...

Nut is a metric M12 threaded nut used as a general-purpose fastener across multiple vehicle assemblies. It runs onto a matching M12 male thread to...

Rear Window Glass for the rear body aperture, in clear glass. It glazes the rear window opening, fitting into the surrounding rubber seal. This is...

Tailgate Finisher is the trim panel fitted to the tailgate, covering the underlying panel structure to give the tailgate a finished exterior appear...

Lower Tailboard Bracket is the left-hand bracket for the bottom-hinged rear tailboard, part of the tailboard mounting assembly. It secures the low...

Heater Air Intake Spacer Tube fitted within the cabin heating system on the Land Rover Defender 90 and 110. This flanged tube locates within the h...

Mud Shield - Under Wing - RH for right-hand drive Series 2 and Series 3 Land Rovers (1968-1984). Fitted beneath the inner front wing on the right-...

Engine Oil Sump for the 2.5L 300 TDi turbo diesel, part of the engine lubrication system. The sump bolts to the underside of the cylinder block an...

Cooler EGR Gasket

MAP Sensor (Manifold Absolute Pressure sensor) for the engine management system, mounted on the throttle housing. It measures the absolute pressur...

EGR Valve for the 2.4L and 2.2L Puma TDCi diesel engines, fitted within the exhaust gas recirculation circuit. The EGR valve meters a controlled p...

Window Regulator - Front Door - Left Hand for the Freelander 1. This is the mechanical actuator assembly mounted inside the front left-hand door th...

Front differential Disco 3,4 & Range Rover Sport

Shock Absorber for the right-hand side of the rear suspension. The shock absorber (damper) controls movement of the rear suspension, damping road-...

Low Ratio Detection Switch - the transfer box range-detection switch, mounted on the front housing of the transfer box. It senses whether the tran...

Flanged Nut - M12 for use in Land Rover fastener applications. A metric M12 flanged nut with an integrated washer flange that distributes clamping...

Fitment: All V8 petrol models (VIN) LA937640 on All 2.5L TD5 diesel models (VIN) 2A638134 on All 2.5L TD5 diesel models to (VIN) 2A638133 All 3...

Clutch Release Fork is the pivoting lever in the clutch release mechanism that acts on the release bearing. Operated by the clutch slave cylinder ...

ABS Sensor Bush is a retaining bush used to locate the wheel speed sensor within its mounting point in the hub or axle assembly. The bush provides...

Rear Propeller Shaft assembly for the rear axle driveline. Installed between the transfer gearbox rear output flange and the rear differential inp...

Bearing transfer box OEM TIMKEN

O-Ring - Diff Lock Selector Shaft - LT230 Transfer Case This O-ring seals the differential lock selector shaft where it passes into the LT230 tran...

Clutch Release Arm Pivot Plate for the LT77 5-speed manual gearbox. Mounts inside the clutch bellhousing and provides the pivot point for the clut...

Rear Left-Hand Half Shaft for the 10/24 spline rear axle. The half shaft transmits drive from the differential to the rear wheel hub. This left-ha...

Rear Axle Half Shaft - right-hand, 10/24 spline, for the Series III rear axle. This shaft transmits drive from the rear differential to the rear wh...

Flanged Hex Bolt, M12 x 70mm. Secures the front wheel hub assembly to the steering knuckle (upright) within the front suspension and hub assembly....

Dowel Ring locates the cylinder head to the block deck on the 200 TDi and 300 TDi diesel engines. Seated in the block face at the head-to-block jo...

Exhaust Manifold for the 2.5L 4-cylinder petrol engine. Bolts to the exhaust ports on the cylinder head and collects the exhaust gases from each cy...

Exhaust Downpipe with Cat is the front section of the exhaust system for the 300TDi engine, incorporating the catalytic converter. It bolts to the...

A/C Belt Tensioner Cover for the air conditioning belt drive on 300TDi engines. This cover fits over the tensioner pulley assembly in the A/C auxi...

Poly-Vee Drive Belt for the Rover V8 petrol engine, in the specification fitted to vehicles equipped with ACE (Active Cornering Enhancement) and ai...

Connecting Rod - 2.25L Diesel

Cylinder Head Gasket for the 2.5L 200TDi and 300TDi diesel engines, supplied in the 1.4mm compressed-thickness grade (identified by two holes). Th...

Cylinder Head Gasket for the 2.5L 200TDi and 300TDi diesel engines, supplied in the 1.3mm compressed-thickness grade (identified by a single hole)....

Washer Pump for the rear screen washer system. The pump pressurises the washer fluid circuit to deliver fluid to the rear screen jet. Mounts in th...

Wiper arm Defender RHD 2A on

Enhance the performance and handling of your Defender 110 with this rear coil spring pair. Designed for heavy-duty use, these yellow springs are pe...

Swivel Housing Repair Kit renews the front axle steering swivel assembly where the swivel housing has become corroded, worn or is leaking. The swi...

Stainless Braided Brake Hose Kit for the flexible sections of the hydraulic braking circuit on non-ABS applications, supplied in standard length. ...

Suspension Bush Kit is a complete set of polyurethane suspension bushes covering the front and rear radius arm mountings and the Panhard rod, suppl...

Exterior Door Mirror Assembly bolts to the front door structure and carries the rear-view mirror glass together with its adjustment mechanism. Thi...

Rear Outer Seat Belt Assembly - the outer restraint serving the forward-facing second-row seat, within the rear seat belt system. This is the long...

Adhesive Tape Decal - a self-adhesive badge decal for the bodywork. Applied to the exterior panel as a logo/badge marking, in light grey. Length 2...

Sliding Window Pair - clear glass side windows within the body glazing, supplied as a pair. Each framed unit carries horizontally sliding clear gl...

Direction Indicator Lamp is a rear amber turn-signal lamp to NAS (North American Specification) pattern in the 95mm round format. It is supplied a...