Land Rover Parts

Front Seat Belt Assembly - right-hand inertia reel unit in the occupant restraint system. Installed at the front right-hand seating position, it p...

Restore your Series or Defender Land Rover's door with this door bottom repair section. This replacement piece is designed to repair damaged or rus...

Gear Knob - gear lever knob for the R380 5-speed manual gearbox. Threads onto the gearchange lever, forming the driver's hand grip and gear-select...

Brake Shoe Return Spring for the rear drum brake assembly, fitted at the upper end of the brake shoes adjacent to the wheel cylinder. The spring h...

Felt Washer for the output shaft assemblies of the LT230 transfer box. This washer is fitted at the front and rear output flanges of the LT230, wh...

Power Steering Pump is the engine-driven hydraulic pump at the heart of the power-assisted steering circuit on the 300 TDi 2.5L turbo diesel. Belt...

Ignition Coil for the ignition system of 4-cylinder petrol engines. The coil steps up the low-voltage supply into the high-tension output that fir...

Flasher Relay installed in the indicator and hazard-warning circuit, controlling the flash rate of the turn-signal lamps. This 12V electronic unit...

Nyloc Nut - M14 - self-locking nut with a nylon insert set into the collar. The nylon insert grips the bolt thread to resist loosening under vibra...

Rear Reverse Lamp - reversing lamp for the rear lighting assembly, providing white illumination to the rear when reverse gear is selected. It moun...

Thermostat for the engine cooling circuit, controlling coolant flow between the engine and radiator. The valve stays shut while the engine warms f...

Differential flange 4-spline

Spring Bush for the leaf spring suspension system on Series Land Rovers. This rubber bush fits into the spring eye at the front fixed mount and re...

Shock Absorber Bush for the lower mounting of a suspension damper. The rubber bush seats in the shock absorber's lower mounting eye, locating the ...

Oil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...

Front Hub Lock Washer located within the Front Hub & Driveshaft Assembly, securing the hub bearing retaining nut in position. The lock washer ...

Gearbox Mount, right-hand side. Part of the transmission mounting assembly. The mount sits between the gearbox and transfer box casing and the cha...

Water Pump Gasket seals the coolant pump to the engine front cover on the V8 petrol engine. It fits at the pump mounting face, sealing the coolant...

Heater Hose - S Shape carries coolant from the engine to the heater matrix in the Series III cabin heating circuit. The hose has an S-shaped profi...

Universal Joint for the axle half shaft, allowing the shaft to transmit drive through an angle. The joint sits within the half shaft and lets it t...

Ignition Coil for the ignition system of 4-cylinder petrol engines. The coil steps up the low-voltage supply into the high-tension output that fir...

Window Channel - Top is the upper glass-run channel that guides the top edge of the window glass, supplied as a 94 cm length. It forms the running...

NAS Link Lead Extension – a three-wire extension link loom for the rear lighting circuit. It connects the rear stop/tail lamp to the vehicle body ...

Fitment All TD5 diesel models up to (VIN) 6A999999 All TD5 diesel models All V8 EFi petrol models 2.5L 6 Cyl BMW Diesel /4.0L and 4.6L EFI V8 P...

Drain Plug Removal Tool for slackening and refitting the square-recess oil drain plugs fitted to Land Rover axles, gearboxes and engine sumps. The...

Speedometer Cable connects the speedometer drive on the gearbox to the speedometer head in the instrument cluster. The rotating inner cable transm...

Cylinder Head Dowel for the Td5 2.5L 5-cylinder turbo diesel engine. The dowel locates between the cylinder block and the cylinder head, aligning ...

Radius Arm Bush - Rear, Lower - the compliant mount at the lower link of the rear radius arm, between the arm and its chassis bracket. The rear ra...

Bonnet Hinge Bolt Kit - a set of stainless steel fixings for mounting the bonnet hinges that allow the bonnet to pivot open. The kit secures the h...

Steering Relay Assembly within the steering linkage. The relay transfers steering movement from the steering box drop arm to the drag link, passin...

Nut, 1/2" UNF. A threaded fastener used on the early 4-cylinder diesel engine assembly.

Upper Ball Joint for the front axle steering knuckle (swivel housing) assembly. The knuckle pivots on an upper and a lower ball joint; this upper ...

Fitment: All models to (VIN) KA930455 All models 1980 on

Transfer Box Output Flange Oil Seal is a radial shaft seal fitted at the output flange of the LT230 transfer box, sealing between the rotating outp...

Escutcheon Seal for the exterior door handle escutcheon. The seal sits between the lock barrel and the outer door skin, sealing the aperture where...

Rear Mudflap for the right-hand side, supplied with its mounting bracket. It forms part of the exterior body protection, fitting behind the rear wh...

Nut - a plain full hex nut with a 3/8" BSF (British Standard Fine) thread. A general-purpose imperial fastener used at many points across the engi...

Switch indicator Defender to GA455945 replacement

Fuel Tank Mount is a rubber mounting that supports the fuel tank on the chassis. It cushions the tank on its mounting bracket, isolating it from c...

Nyloc Nut - 1/4" UNF - self-locking nut with a nylon insert set into the collar. The nylon insert grips the bolt thread to resist loosening under ...

Front Bumper for the front-end body structure, finished in black. The bumper mounts across the front of the chassis to form the front impact face ...

Window Regulator Handle for manually operated door windows on the Defender. This crank-type handle attaches to the window regulator spindle on the...

Flanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...

Oil Seal Housing Gasket for the 300 TDi engine, sealing the rear crankshaft oil seal housing to the rear face of the cylinder block. The gasket fo...

Coolant Bypass Hose for the 4-cylinder petrol and naturally-aspirated diesel engines (non-TDi). It forms the bypass path of the engine cooling cir...

Hydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...

Anchor Stud providing a threaded fixing point for interior trim panels, door casings, carpet sections, and air intake duct components. This stud a...

Stub Axle Gasket for the rear drive shaft assembly on Land Rover Series II, IIA, and III. This gasket seals the stub axle flange at the rear axle ...