Land Rover Parts

Rear Wheel Cylinder Repair Kit for the rear drum brakes. This is a seal/overhaul kit that reconditions the rear brake wheel cylinder in situ, rest...

Side & Flasher Lamp Lens for the front combined side and direction-indicator lamp, right-hand side. The lens fits over the front side (parking...

Side & Flasher Lamp Lens for the front combined side and direction-indicator lamp, left-hand side. The lens fits over the front side (parking)...

Suppressor Capacitor mounted at the ignition coil as part of the ignition system. It suppresses the radio-frequency interference generated by the ...

Self-Tapping Screw - a No. 6 x 1/2" imperial self-tapping fixing used as a general-purpose fastener throughout the body and chassis. The self-tapp...

Front Exhaust Pipe - downpipe section of the exhaust system. Connects the exhaust manifold to the intermediate pipe and silencer, carrying exhaust...

Output Shaft Bearing for the LT76 gearbox, a taper roller bearing that supports the rear output shaft. It locates the output shaft within the gear...

Fuel Filler Screw is a 2BA x 3/8" fastener used to secure the fuel filler fitting. It retains the fuel filler to the body panel; the companion nut...

Thermostat for the engine cooling circuit of the 2.6L six-cylinder petrol engine. It regulates coolant flow between the engine and radiator, stayi...

Third-Speed Mainshaft Gear for the manual gearbox. It is the 3rd-speed gear carried on the gearbox mainshaft, meshing with its layshaft gear to pr...

Oil Pressure Transmitter for the V8 engine oil pressure gauge circuit. This single-terminal sender threads into the engine oil gallery and varies ...

Exhaust Connecting Pipe is the intermediate section of the exhaust system, linking the front downpipe to the rear silencer assembly in the Series E...

Upper Rear Door Seal, the rubber weatherseal for the top edge of the rear door aperture. It seals the upper line of the rear door against the body...

bottom door Series RH Series 3

Sedimentor Drain Plug with Seal for the diesel fuel filter assembly. Fitted at the base of the sedimentor bowl, this plug allows the bowl to be dr...

Door lock RH

Fitment: all models to 1980

Barrel Lock and Key, Set of Three for the door locks, supplied as three keyed lock barrels each with a key. Each barrel is the cylinder the key tu...

Front leaf spring LWB diesel DS

Leaf spring 88 / 109 diesel passengers 11L

Connecting Rod Bearing Set for the 2.5L 4-cylinder engine, supplied in 0.030" oversize. These are the big-end shell bearings that fit between the ...

Turbocharger to Intercooler Hose for the 300TDi 2.5L turbocharged diesel engine intercooler circuit. This hose connects the turbocharger compresso...

Dual Battery Management System - a microprocessor-controlled split-charge controller for a two-battery electrical setup. It manages a starter batt...

Hex Nut - 7/16 UNF fixing nut. Used on the fuel pipe unions of the 3.5L V8 twin-carburettor petrol engine. Also supplied as part of a service kit.

Windscreen Filler Strip closes and trims the gap between the windscreen glass and the body aperture, forming part of the windscreen sealing and fin...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Bolt with Whitworth (BSW) thread - 1/4 inch diameter, 1-1/4 inch length, sold individually. Used across Series Land Rover applications requiring t...

Fuel Leak-Off Tube Kit - TDV6

Timing Belt Kit Timing belt kit for the timing drive of the 2.7L and 3.0L TDV6 (Lion) diesel engine, synchronising crankshaft rotation with the cam...

Battery Wing Nut secures the battery hold-down clamp within the battery mounting assembly, threading onto the clamp rod to hold the battery firmly ...

Bolt for the upper front suspension arm. This fastener secures the upper front suspension arm within the front axle and suspension assembly.

Piston for the 2.25L four-cylinder petrol engine, machined to +0.030" oversize for a rebored cylinder block. The piston runs in the cylinder bore ...

Headlamp Washer Jet is the nozzle of the headlamp washer system, mounted at the front of the vehicle adjacent to the headlamp. It directs pressuri...

Expansion Tank - the coolant expansion and overflow reservoir in the engine cooling system. Mounted in the cooling circuit, it accommodates the ch...

Power Assisted Steering Hose for the 4-cylinder non-Tdi engine, part of the hydraulic steering circuit on right-hand drive Defender 90 and 110 mode...

Rear Light Guard - Single - Natural is a steel mesh protective guard for a single rear lamp. It bolts over the rear lamp lens to shield it from im...

Alternator serving the charging circuit of the 2.7L and 3.0L V6 diesel (TDV6) engine. Driven by the accessory drive belt, the alternator converts ...

Brake Pipe - Rear is a rigid hydraulic line forming the fixed section of the rear brake circuit, carrying pressurised brake fluid from the chassis-...

Flange Nut An M16 flange nut used on the front suspension arm and stabiliser mountings. The integral flange spreads the clamp load across the moun...

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 5th gear selector bias. It works within the gear lever remote housing...

Injector Pipe Clip for the diesel fuel injection system. The clip secures and spaces the high-pressure injector pipes, damping vibration and preve...

Inlet Valve for the cylinder head valvetrain of the Rover V8 petrol engine (3.5L, 3.9L, 4.0L and 4.6L variants). It seats in the cylinder head inl...

Bumper Fitting Kit (Rear) supplies the mounting hardware required to fit the companion rear heavy-duty bumper (DA5646) to the vehicle's rear chassi...

Rear Bumperettes - a pair of tubular bumperettes that bolt to the rear crossmember to protect the rear corners of the body and the rear lamps from ...

Diecast Scale Model of the Land Rover Defender 90, finished in Tamer Blue, at 1:76 scale. The body is cast in metal with a painted finish and moul...

Front Seat Base Cover is a replacement upholstery cover for an outer front seat, fitting over the base cushion foam to form the wearing surface the...

Fresh Air Grille Finisher for the fresh air intake, left-hand side. This capping finisher trims the fresh air intake grille on the body, covering ...

ACE Strut Actuator - the hydraulic actuator for the front Active Cornering Enhancement (ACE) anti-roll bar. ACE replaces a conventional passive an...