Land Rover Parts

LINK - TOE - SPINDLE ROD - D3/D4/RRS 05-09/RRS 10-13 OEM MOOG

Cable

Pipe Clamp for the engine oil cooler pipe circuit. This clamp plate secures the oil cooler pipes in the engine bay, restraining them against vibra...

seal rubber infill for doortop glass / sliding front and rear windows OEM 110" 1983 - 1984

Bar Anti Roll Bush

Gasket

Hydraulic Lash Adjuster installed within the valve train assembly of Td5 2.5L 5-cylinder turbo diesel engines, positioned between the camshaft and ...

Adjustable Panhard Rod - lateral axle location link, supplied with polyurethane bushes. The panhard rod locates the axle laterally relative to the...

Hex Bolt - M10 x 120mm is a metric hexagon head bolt used in multiple assemblies on Land Rover vehicles. Applications include the front bumper mou...

Spring Plate that retains the soft top (tilt) hood frame. Works with the tilt stud to clamp the canopy in place. Used with stud AFU2503 and ring A...

Rear Leaf Spring for Series IIA and Series III 109" wheelbase 1-ton and Extra Heavy Duty Land Rovers. Suitable for both left-hand and right-hand si...

Headlamp Bezel is the outer retaining surround for the headlamp unit, mounting within the front lighting panel. It secures and finishes the lamp a...

Mainshaft Bearing for the gearbox mainshaft - the centre bearing that supports the mainshaft within the gearbox casing. It locates and carries the...

Camshaft Bearing Set for the Rover 3.5L V8 petrol engine. Supplies the bearing shells that support the camshaft as it runs within the cylinder blo...

Fuel Sedimentor is a water and sediment trap in the diesel fuel supply line, installed upstream of the fuel filter and injection pump. Fuel passes...

Handbrake Cable Bracket for the parking brake cable assembly. This bracket mounts to the body or chassis to guide and anchor the handbrake cable, ...

Rear Seat Cushion Latch secures the rear seat cushion of the forward-facing split rear seat, holding the cushion in position and releasing it so th...

J Bolt for the battery mounting assembly. The J-shaped threaded bolt hooks through the battery mounting bracket. The threaded end accepts a nut to...

Latch hood, bonnet, RH and LH, with sensor

Front Differential Bush Mounting bush that locates and supports the front differential within the axle case. The bush isolates the differential fr...

Towing Jaw rated to 3.5 tonnes, part of the towing/pintle hitch assembly. It provides the jaw coupling for trailer and recovery towing, mounting t...

Reverse Shaft for the reverse gear train in the Series-type manual gearbox (LT76), suffix B onwards. The shaft carries the reverse idler gear, whi...

Head Gasket - Metal for the 3.9L V8 EFI engine, sealing the cylinder head to the engine block in the top-end assembly. This multi-layer steel head...

Throttle Linkage for the 3.5L V8 fitted with twin Stromberg 175CD carburettors. This linkage connects the throttle pedal input to both Stromberg c...

Upgrade your Land Rover Series 2A & Series 3 SWB (1980-1984, Metric) with this +40mm stainless steel brake hose kit. +40mm Extended Length -...

Load Bay Liner Kit lines the rear load area to protect the original bed and inner surfaces from cargo abrasion, impact and moisture. The liner is f...

Central exhaust pipe Discovery 300TDI Stainless Steel

Polyurethane Bush Kit - a complete-vehicle suspension bush set that replaces the rubber mounting bushes throughout the axle-location linkages. The...

Coolant Temperature Sensor - Green for the engine cooling and fuel management circuit in the 3.9L and 4.0L V8 petrol engine. A thermistor-type sen...

Screw for securing the chaffguard to the body structure on Series Land Rovers. The chaffguard protects adjacent components from abrasion and heat;...

Timing gear lower idler pulley for the engine timing drive system. This pulley guides and stabilizes the timing belt within the lower timing gear...

Front Bumper End Capping, right-hand, for the outboard end of the front bumper. The capping closes off the right-hand end of the front bumper, fin...

Exhaust Front Pipe (down pipe) for the 2.5L turbo diesel (non-TDi) exhaust system. Connects the turbocharger/manifold outlet to the intermediate e...

Seat Recline Mechanism Cover - RH is the trim cover plate fitted over the front seat recline adjuster mechanism. It conceals and protects the recl...

Front door latch LH D1, RRcl

Nut Plate for the body-side striker mountings, part of the door and tailboard latch assembly. The plate provides captive threaded anchor points be...

Timing Belt Kit

Flanged Nut - M10 flanged fastener. The integral flange spreads the clamping load over a wider area and resists loosening under vibration, removin...

Temperature Sensor for the V8 EFI engine management system. It monitors engine coolant temperature and signals the electronic fuel injection ECU, w...

Coil Spring for the suspension system of the Range Rover Classic, for left-hand drive (LHD) variants. This left-hand spring is identified by its g...

Flywheel Timing Pin - an engine timing tool for 4-cylinder diesel engines that locks the flywheel at top dead centre (TDC) so the crankshaft is hel...

Brake Pad Set for the rear axle disc brake assembly. The friction pads locate within the rear caliper and are clamped against the brake disc to ge...

Bonnet Release Cable connects the interior release handle to the bonnet latch mechanism. Pulling the cabin lever draws the cable to release the lat...

A/C Receiver Dryer sits on the high-pressure side of the R134a air conditioning circuit, between the condenser and the expansion valve. It stores l...

Needle Roller Bearing for the R380 manual gearbox. It carries the reverse idler on the layshaft, allowing the gear to rotate with minimal friction ...

Gearchange Housing Gasket for the LT85 five-speed manual gearbox. This gasket seals the interface between the gearchange housing and the main gear...