Land Rover Parts

Watts Linkage Bolt is an M14 fastener used in the rear suspension. It secures the Watts linkage to the rear axle, and is used in the same specific...

Anti Roll Bar Bush locates the anti-roll bar in its chassis mounting bracket, providing a resilient rubber interface between the bar and the subfra...

Coolant Temperature Sensor for the engine cooling system of the 3.5L and 3.9L V8 petrol engine, in both twin-carburettor and EFI form. The sensor ...

Windscreen Washer Jet for the front screen wash system. The jet mounts to the bonnet or scuttle panel and directs washer fluid onto the windscreen...

Headlamp Washer Non-Return Valve fitted in the headlamp washer fluid circuit, in the delivery line between the washer pump and the headlamp jet noz...

O-Ring sealing the air filter housing to the airflow meter on V8 EFI engines. This O-ring seals the joint between the air filter housing outlet an...

Fuel Tank Plug, M12 threaded, fitted to the fuel tank body. It seals a threaded port in the tank associated with the fuel pump, sender and filler ...

Bottom Hose is the lower radiator coolant hose in the engine cooling circuit. It carries cooled coolant from the radiator outlet back to the water...

Spring Washer is a split spring lock washer used at the top of the steering column, at the steering box. Fitted under the securing nut, it maintai...

Lead High Tension Number 1

Roof to Side Seal - Front Upper - RH for the Defender body sealing system. This rubber seal closes the gap between the front upper right-hand edge...

Edge Clip is a fixing used within the body and chassis assembly to secure components to the edge of a panel or flange. The clip pushes onto a pane...

Window Winder Handle for the manual window regulator in the front door of the Range Rover Classic. This handle attaches to the window regulator sp...

Upper Tailgate Finisher for the Range Rover Classic. Trim finisher fitted to the upper tailgate, finishing the top edge and glass aperture surroun...

Valve Cover Gasket for the 4.4L M62 V8 petrol engine, sealing the cylinder head (camshaft) cover to the cylinder head. The gasket seals the perime...

Oil Pump Gasket sealing the oil pump to the cylinder block. Used on the 2.0-litre 4-cylinder T-Series MPi petrol engine and the 2.0-litre 8-valve ...

Flywheel Bolt - hex-head bolt that secures the flywheel to the rear crankshaft flange within the flywheel and crankshaft assembly. Application: 2....

Sump Plug Washer is the sealing washer for the engine oil sump drain plug. It seats between the drain plug and the sump pan to form a leak-tight s...

Bonnet Gas Strut - a gas-filled lift strut for the bonnet, part of the bonnet support assembly. It carries the weight of the raised bonnet and hol...

Oil Filter for the 3.0L TD6 diesel engine, forming part of the engine lubrication and oil filtration circuit. It removes carbon, metal particles a...

Exhaust Manifold Gasket for the KV6 2.5L V6 petrol engine. Seals the joint between the exhaust manifold and the cylinder head, preventing combusti...

Flange Nut - M12 - an M12 fastener with an integral flanged face, used throughout the suspension assembly. The wide flange spreads the clamping lo...

Drive Flange Nut - Front secures the front drive flange (driving member) to the wheel hub, as part of the front hub assembly. It retains the drivi...

Gear Lever Spring for the manual gearbox gear change mechanism, providing the 1st/2nd selector bias. It works within the gear lever remote housing,...

Hexagonal Plug for the swivel pin housing oil level and drain. This hex-head plug is used in the front axle swivel pin housing as both an oil leve...

Thrust Washer 1.45mm Diff - LT230

Thrust Washer for the differential assembly within the LT230 transfer box. This 1.35mm thrust washer sits within the LT230 centre differential, co...

Thrust Washer is a 1.25mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Thrust Washer is a 1.15mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Half Shaft Shim is a 1.50mm selective shim used in the axle drive shaft and hub assembly. It sets the endfloat of the half shaft drive member with...

Shim

Dowel is a precision locating pin that aligns mating components during assembly, setting their position accurately and relieving the securing bolts...

Carburettor Throttle Linkage Roller for the 3.5L V8 twin-carburettor petrol engine. It runs on the throttle countershaft, guiding the carburettor ...

Injector Clip for V8 EFI fuel injection systems, used in the fuel delivery assembly at the intake manifold. This retaining clip secures the fuel i...

Exhaust Valve for the 2.25L 4-Cylinder Petrol engine, fitted in the cylinder head valvetrain assembly. This valve operates in the cylinder head to...

Inlet Valve for the cylinder head valve train, with a 34.5 mm head diameter. The inlet valve opens on the induction stroke to admit the air/fuel c...

Air cleaner filter element

Flywheel Bolt for the 2.5L Td5 five-cylinder diesel engine with manual gearbox. This bolt secures the flywheel to the rear flange of the crankshaft...

Blanking Plug - Metric - Cylinder Head Rear seals the rear coolant gallery opening in the cylinder head on Land Rover 4-cylinder engines. The rear...

Conrod Bolt for Land Rover petrol and diesel four-cylinder engines. This bolt secures the connecting rod cap to the connecting rod, clamping the b...

Wiper Blade with Spoiler for the front windscreen wash/wipe system, for left-hand drive applications. The integral aerodynamic spoiler maintains c...

Mounting Plate for a single towing electrics socket, forming part of the trailer and caravan towing electrics installation. It carries one 12N (7-...

Door Latch Striker Screw - fixing screw that secures the door latch striker to the body pillar. The striker is the catch the door latch engages to ...

Stud Plate located at the rear end door and rear side door check strap attachment points on the Defender 90/110. Provides the mounting face and ca...

Blanking Plug - plastic plug sealing a 1-1/4" (32mm) diameter aperture in the rear cross member. Installs into unused or access holes in the bodys...

Steering Boss Adaptor - a mounting adaptor between the steering column boss and an aftermarket steering wheel. It adapts the fixing pattern of the...

Anti-Roll Bar Link Assembly connects the front anti-roll bar to the suspension, forming part of the front stabiliser linkage. As the vehicle corne...

Rear Wiper Blade - the wiper blade for the rear screen wash/wipe system. It clips onto the rear wiper arm and draws its rubber wiping element acro...