Land Rover Parts

Distributor Bush for the ignition distributor of the 3.5L V8 carburettor engine (Stromberg twin-carb). The bush is seated in the distributor body ...

Thermostat and Housing regulates coolant flow within the engine cooling system. The thermostat opens as the engine reaches operating temperature t...

Main Bearing Kit 010 King

Rectifier Alt Acr

Screw for securing the rear reflector, fog lamp, and reverse lamp assembly on the Land Rover Defender. Used to retain the lamp cluster components ...

Swivel Housing Gaiter Kit - Leather - Pair for the front axle swivel housing assembly on the Defender 90 and 110. The swivel housing gaiter seals ...

Speedometer Cable for Land Rover models fitted with the 2.6-litre 6-cylinder petrol engine. Transmits rotational drive from the gearbox output shaf...

Main Bearing Set for the crankshaft of the 2.5-litre four-cylinder petrol and naturally aspirated diesel engines. Supplies the complete set of mai...

Primary Pinion for the LT76 manual gearbox, suffix D onwards. The primary pinion is the gearbox input gear, taking drive from the clutch and passin...

Main Bearing Set - a set of crankshaft main bearing shells for the Rover V8 petrol engine. The main bearings are the split shell bearings that car...

Lock Washer for the carburettor butterfly spindle. This lock washer secures the retaining nut on the throttle butterfly spindle inside the carbure...

Brake Disc Bolt for the front brake assembly. Secures the brake disc to the wheel hub, locating the disc and holding it in position during wheel a...

Compressor Mounting Bracket - Air Suspension is the bracket that mounts the air suspension compressor to the vehicle. It locates and secures the c...

ACE Pipe - Valve Block To Reservoir - TD5 is a low-pressure return line within the Active Cornering Enhancement (ACE) system. It carries hydraulic...

ACE Pipe – Pump to Valve Block (Front Half) for the Active Cornering Enhancement hydraulic circuit on TD5 diesel applications. This high-pressure p...

Shock Absorber Top Mount Bush for the front suspension – the rubber bush at the upper end of the front damper. The bush isolates the top of the fr...

Steering Box Seal Kit provides the seals for servicing the input assembly of the power-assisted steering box. This kit is used during steering box...

Power Steering Hose from the power-assisted steering hydraulic circuit, for right-hand-drive applications. It routes pressurised hydraulic fluid t...

Quarter-Turn Fastener for the radiator and cooling system assembly. This fastener secures a panel or component at the radiator with a quick quarte...

Front Indicator Assembly - Right-Hand for the Discovery 1 front lighting cluster. This is the complete right-hand front indicator lamp assembly, p...

Steering Column Lock for the Range Rover Classic, incorporating the mechanical steering lock cylinder and the ignition switch in a single column-mo...

Speedo Cable

Switch

Speedometer Cable - LHD (gearbox end section) for the Range Rover Classic speedometer drive assembly. The two-piece speedometer cable on left-hand...

Heater Blower Switch for the heating and ventilation control assembly. This switch controls the fan speed settings of the cabin heater blower moto...

Double Clip for routing and securing battery cables. This twin clip retains two leads together, holding the cabling in place along its run.

Wiper and Washer Switch for the dashboard wiper and washer control assembly. This combination switch controls both the windscreen wiper motor - pr...

Speedometer instrument head for the dashboard instrument panel, incorporating a resettable trip odometer alongside the main total odometer. The sp...

Alternator Belt for the auxiliary drive belt system of the 4.0L and 4.6L V8 EFI petrol engine. This poly-V drive belt transfers power from the cra...

Idler Pulley for the auxiliary drive belt system on the V8 Petrol engine. This fixed pulley guides the auxiliary drive belt around the engine acce...

Water Pump from the engine cooling system of the Td5 2.5L 5-cylinder turbo diesel. It circulates coolant through the cylinder block and cylinder h...

Plenum De-icer Hose for the V8 petrol intake system. The hose runs between the inlet manifold and the plenum chamber as part of the plenum de-icing...

Radiator Bottom Hose is the lower coolant hose of the engine cooling circuit. It carries cooled coolant from the radiator's lower outlet back to t...

Radiator Assembly for the V8 petrol engine cooling circuit. This radiator assembly is the primary heat exchanger in the engine cooling system. Coo...

Rear Bumper Assembly for the Discovery 1. This is the complete rear bumper unit, fitted to Discovery 1 vehicles built up to (V)LA series. It mount...

Exhaust Silencer for the 200Tdi 2.5L Turbodiesel exhaust system, non-catalyst specification. Fits in the mid-to-rear section of the exhaust system...

Choke Cable for the V8 carburettor engine, part of the manual choke control system on right-hand drive Defender 90 and 110 models. This cable conn...

Fuel Tank Mounting Spacer sits at the rear fuel tank mounting, setting the standoff between the tank mounting bolt plate and the chassis. It maint...

Front exhaust Y-pipe from the front section of the exhaust system, joining the two cylinder-bank downpipes into a single gas flow. On the V8 each ...

Exhaust Downpipe for the 2.5 Petrol engine. This pipe connects the exhaust manifold to the main exhaust system, routing combustion gases away from ...

Rear Exhaust Silencer for the Defender 90, installed as the rearmost component of the exhaust run, downstream of the centre section. Applies to th...

Intermediate Exhaust Pipe for the 2.5L petrol engine, connecting the front downpipe to the centre silencer in the Defender exhaust system. Pipe le...

Fuel Filter Assembly within the diesel fuel supply circuit, removing contaminants from the fuel before it reaches the injection system. Installed ...

Exhaust Pipe