Land Rover Parts

Alternator with integral vacuum pump, 105 A output, for the 2.0L TCIE four-cylinder diesel engine in air-conditioned specification. Belt-driven fr...

Horn - High Note

Transducer Coolant Temperature

Description: TRANSDUCER-SPEEDAll product codes / identifiers: YBE100530G YBE100530G

Handbrake Pad Set - replacement friction pads for the X-Eng disc handbrake (transmission brake) conversion. The conversion replaces the drum-type ...

Brake Light Switch, the stop lamp switch mounted at the brake pedal. When the brake pedal is depressed the switch closes the stop lamp circuit to ...

Bulb Holder - double-pole bulb holder for the rear stop and tail lamp. It carries the twin-filament stop/tail bulb and locates by bayonet fitting ...

Number Plate Lamp Lens - clear lens for the rear licence plate lamp mounted in the luggage compartment door. The lens clips into the lamp housing ...

Stop & Tail Lamp - 24V is a combined rear stop and tail lamp unit for vehicles running a 24 V electrical system. The unit carries both functio...

LED Number Plate Lamp - rear licence plate lamp using LED illumination. Mounted above the rear number plate, the lamp illuminates the plate for ni...

Rear Lamp Assembly - Stop & Flasher - rear lamp cluster within the rear exterior lighting assembly group, combining the stop lamp and direction...

Rear Bumper Lamp, Right-Hand Side. Lamp unit installed in the right-hand side of the rear bumper, forming part of the rear exterior lighting assemb...

Lamp Assembly-Rear

Handbrake Disc - transmission-mounted brake disc, the rotating element of the disc-type transmission handbrake conversion. Mounts on the transfer ...

Asy Lamp

Crankshaft Oil Pump Seal Front crankshaft oil seal located in the oil pump housing. Seals around the crankshaft snout where it passes through the ...

Plain Washer - flat steel washer from the hardware and fixings group. It is fitted under a bolt head or nut to spread the clamp load over the join...

Fuel Tank Filler Hose - moulded connecting hose from the fuel tank filler assembly. It joins the filler neck at the body aperture to the inlet spi...

Fuel Pipe Assembly forming the vent lines of the Td5 2.5L 5-cylinder turbo diesel fuel system. The vent pipework carries fuel vapour away from the...

Fuel Filter is the cartridge-type filter in the diesel fuel supply circuit, mounted between the tank and the injection pump. It removes particulat...

Washer is a plain fastener hardware component used in bolted and studded joints. It seats between the nut or bolt face and the mounting surface to...

Fuel Pump & Sender - in-tank low-pressure fuel pump and fuel level sender assembly for the Td5 2.5L 5-cylinder turbo diesel. The unit mounts v...

Fuel Pump and Sender Unit - the in-tank assembly combining the electric fuel lift pump with the fuel level sender, part of the fuel tank pump, send...

Serrated Washer, 7/16", used within the clutch master cylinder and pipe assembly. The serrated face bites into the mating surface as the fixing is...

Exhaust Gas Temperature Sensor for the diesel exhaust aftertreatment system, fitted to vehicles equipped with a diesel particulate filter (DPF). T...

Exhaust Mounting is a moulded rubber mounting that suspends the front section of the exhaust system from the vehicle body. The rubber body links t...

Exhaust Gasket sealing a flanged joint in the exhaust system on Land Rover and Range Rover models fitted with the 2.7L TDV6, 3.0D V6, 2.2D, and 4.4...

Restrictor

EGR Blanking Plate for the exhaust gas recirculation circuit on the Td5 2.5L 5-cylinder turbo diesel. The plate installs at the joint between the ...

Worm Drive Hose Clamp used in the exhaust gas recirculation (EGR) circuit of the 3.0L M57 turbo diesel engine. The clamp secures a flexible hose o...

Worm Drive Hose Clamp - worm-type clamp used in the exhaust gas recirculation system of the 3.0L M57 D30 turbo diesel engine. It secures the flexi...

Nut - Hex

Parking sensor bezel in black, the retaining trim ring that locates a Park Distance Control (PDC) ultrasonic sensor in its bumper aperture. The be...

Loadspace rubber mat for the rear load compartment, part of the interior protection group. The mat is tailored to the loadspace floor and protects...

Side step insulator - a moulded pad that sits between the side step mounting bracket and the vehicle body, within the deployable side step mounting...

Kit - Floor Contour Mat

Mud Flap - a moulded rubber rear mud flap with a ribbed face, hung behind the rear wheel to intercept water, mud and stones thrown up by the tyre. ...

Tow Bar Electrics Kit - the 13-pin electrical interface between the vehicle and a towed trailer or caravan, forming the electrical half of the tow ...

Grub Screw for the gearbox and transfer box selector mechanism. This is an M10 grub (set) screw that locks a selector fork or yoke onto its select...

Plug

Gearbox Bearing - layshaft taper roller bearing for the LT77 five-speed manual gearbox. The layshaft turns whenever the clutch is engaged, carryin...

Bush - Steering Column

Layshaft Bearing - taper roller bearing supporting the layshaft in the R380 5-speed manual gearbox. The bearing carries the countershaft (layshaft...

Gearbox Seal - MT82 Output Shaft for the MT82 six-speed manual transmission. This oil seal fits at the output shaft of the MT82 gearbox, sealing t...