Land Rover Parts

Piston Assembly for the 2.5L 300 TDi four-cylinder diesel turbo engine, machined to 0.010in (0.25 mm) oversize for a rebored block. Each assembly ...

Fuel Filter for the diesel fuel supply system — the cartridge that cleans fuel on its way to the injection pump. The filter traps particulate cont...

Outer Sill for the left-hand side of the 5-door body - the outer panel covering the lower bodyside (rocker) section beneath the doors. The outer s...

Taper Roller Bearing - outer pinion bearing in the differential final drive assembly. The drive pinion is carried on a pair of opposed taper rolle...

Gasket & Bolt Kit - 300TDi - Without Head Gasket

O-Ring for the electronic air suspension pipework - the seal that sits inside the collet fitting where an air pipe enters a valve block, air spring...

Alternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...

Trans Temp

Guide Pin for the auxiliary drive belt tensioner and front timing cover on the 2.5L six-cylinder diesel. The pin locates the tensioner assembly to...

Petrol Piston Ring 010

Caliper

Engine Overhaul Gasket & Seal Set for the 200TDi diesel engine, covering the bottom end of the engine. This set provides the gaskets and seals...

Tank Unit

Brake Caliper for the front axle, right-hand side, part of the front disc brake assembly. Hydraulic pressure delivered through the brake line acts...

Wiper Blade for the windscreen wiper system. The blade carries the flexible rubber wiping element in a sprung metal frame that follows the curvatu...

ABS Wheel Speed Sensor for the front hub, part of the anti-lock braking system. The sensor mounts at the front hub carrier and reads the rotating ...

Handbrake Operating Lever from the parking brake control assembly. The lever is the driver-operated arm that applies the transmission brake through...

Adjusting Lever

Brake Calliper Fitting Kit for the rear brake callipers. This kit contains the slider pins and rubber dust boots for the rear brake calliper. The ...

Brake Caliper Repair Kit for the rear brake caliper assembly - a piston seal kit for renewing the caliper's hydraulic sealing at the piston bore. ...

Rear Wheel Brake Cylinder for the rear drum brake assembly, bolted to the brake backplate above the shoes. Hydraulic pressure from the master cyli...

Brake Master Cylinder - tandem master cylinder assembly at the head of the hydraulic braking system, mounted to the front face of the brake servo o...

Rear Brake Hose Bracket - mounting bracket that anchors the rear flexible brake hose to the chassis, holding the rigid-pipe-to-hose union in a fixe...

Brake Hose - the centre (intermediate) flexible hose in the rear braking hydraulic circuit. It bridges the chassis-mounted rigid brake pipe to the...

Brake Hose flexible hose for the front right-hand hydraulic braking circuit. Connects the fixed rigid brake pipe to the front right-hand brake cal...

Distributor Setscrew is the clamping fastener for the distributor within the ignition system of the 3.5L V8 twin-carburettor petrol engine. It sec...

Brake Pipe T-Piece is a hydraulic junction in the rear braking circuit, connecting the incoming brake line to the rigid pipes serving the rear whee...

Brake Pipe T-Piece is a three-way hydraulic union in the rear braking circuit, joining the incoming brake line to the two rigid pipes that feed the...

Brake Pipe Clip is a retaining clip from the front brake line mounting hardware. The double form holds two rigid brake pipes side by side at a fix...

Brake Pipe is a rigid, pre-formed hydraulic line within the braking system. It carries pressurised brake fluid between the master cylinder, the AB...

Handbrake Shoe Set for the mechanical parking brake, which operates inside its own dedicated drum and is independent of the hydraulic service brake...

Exhaust Valve Guide is pressed into the cylinder head and supports the exhaust valve stem, keeping it accurately centred as the valve opens and clo...

Brake Pad Set for the front axle disc brake assembly. The pads locate within the front calipers and clamp against the vented front discs, generatin...

Brake Pad Set - Front - friction pads for the front disc brake caliper assembly, for the vented front disc installation. The pads locate in the fr...

Service Kit Sticker - adhesive service label, supplied in a pack of 25.

Transmission Brake Drum for the LT230 transfer box transmission brake - the drum-type parking brake mounted on the transfer box rear output. The d...

Disc - Brake

Disc - Brake

Brake Disc - a front vented brake disc, the rotating friction surface the caliper pads clamp against to slow the vehicle. The internal vanes draw ...

Screw - threaded fastener specified in two unrelated assemblies: securing components to the cylinder block of the 2.5L 5-cylinder turbo diesel engi...

Single aluminium clamp set - roll-cage accessory mount used to fix equipment such as a roof rack, snorkel or aerial to external cage tubing. The c...

Hex Head Bolt is a hexagonal-head threaded fastener used as a mounting bolt on the vehicle. It is driven with a standard hexagonal socket or spanner.

Bolt

Hex Nut is an M6 flange nut with a 10mm hexagonal drive. It retains wheel arch liner and splashguard panels on their mounting studs. The integral ...