Land Rover Parts

Mounting Bolt for the fuel tank pump and mounting assembly. It secures the fuel pump and its mounting bracket at the tank mounting point in the fu...

Plate - Power Steering Pipes is the retaining plate in the power steering pipe assembly. It clamps the steering pipe run at its mounting point, ho...

Wheel Nut for alloy wheel fitment on Defender, Discovery 1 and Range Rover Classic. This tapered-seat wheel nut is designed for use with alloy whe...

Shock Absorber Bush Set for the upper damper mounting, polyurethane. The bushes sit in the upper damper mounting, isolating the damper from its mo...

U-Bolt clamping a leaf spring to the axle casing in the leaf spring suspension mounting. The bolt passes over the axle casing and draws the spring...

Drag link for the steering linkage, connecting the steering box drop arm to the steering arm on the front axle. The drag link converts the arc des...

Pre-shaped rear brake pipe for the rear hydraulic braking circuit, carrying fluid from the axle-mounted T-piece to the rear wheel cylinder. The pi...

Spark plug for the ignition system. The plug threads into the cylinder head and is fired through the HT lead from the ignition coil, delivering th...

Distributor Cap for the Freelander 1 ignition system. The distributor cap fits over the distributor body and routes the high-voltage output from t...

Hex full nut with a 1/2 inch UNF thread and a zinc-and-yellow passivate finish, catalogued in the towbar and towing equipment mountings. The zinc-...

HT Ignition Lead - T-Series - No.4 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary igniti...

Wireasy-Ignition

Wireasy-Ignition

Wireasy-Ignition

O-Ring - Fuel Injector - Td4 Diesel - sealing ring in the fuel injector and pipe assembly of the Td4 2.0L 16-valve diesel engine. The ring seals t...

Acme Thread Screw for the front wing assembly, part of the body panel fixing hardware. The hex-head screw uses a coarse Acme thread form that bite...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Door Casing Stud - plastic push-fit stud used to secure interior trim panels to the door frame and body structure. The stud passes through the tri...

Window Seal - glazing seal for the cab body rear panel window, part of the cab rear panel glazing assembly. The seal locates in the rear panel ape...

Rubber Buffer

Glazing rubber for the window lift channel, from the front door glass and regulator assembly. The rubber lines the U-section lift channel that the...

Rear end door casing - the interior trim panel that finishes the inner face of the rear end door. The casing closes off the door's inner structure...

Rear door glass guide bracket from the rear side door window regulator assembly. The bracket anchors the glass guide channel to the inner door str...

Filter Fuel Element

Galvanised Body Cappings Bracket is the rear body cappings corner bracket for the left-hand (LH) side. The bracket supports and locates the rear b...

Galvanised Body Cappings Bracket is the rear body cappings corner bracket for the right-hand (RH) side. The bracket supports and locates the rear ...

Gear Lever Gaiter, Inner. Flexible boot in the gear lever and transmission tunnel assembly. It seals the aperture where the main gearbox lever pas...

Crossbrace, Lock Panel to Body. Left-hand structural brace from the grille, top panel and brace assembly at the front of the vehicle. It ties the ...

Door Check Drag Link is part of the rear door check mechanism. It restrains and controls the travel of the side-hinged rear end door as it swings o...

Bonnet Prop Rod, scissor type. Part of the bonnet and hinge assembly, it holds the bonnet in the raised position and folds flat against the bonnet ...

Drain Channel for the left-hand (LH) side, part of the soft-top drain channel assembly that runs along the upper body edge. The channel collects r...

Drain Channel for the right-hand (RH) side, part of the soft-top drain channel assembly that runs along the upper body edge. The channel collects ...

Rear mudflap for the right-hand side. Moulded rubber flap that hangs behind the rear wheel and bolts to the mudflap bracket under the rear body, sh...

Tie Tube

Front Roof Capping - RH - external capping section fitted along the right-hand front edge of the roof, covering the joint between the roof panel an...

Radiator Grille Bracket in stainless steel, part of the front panel and radiator grille mounting assembly. The bracket fixes to the inner face of ...

Fixing Clamp-BA

Fuel Injection Pump for the Td4 2.0L four-cylinder 16-valve turbo diesel engine - the high-pressure stage of the common rail fuel injection system....

Stud used in the rear body upper fixings. The stud provides the threaded shank at the upper mounting points where the rear body ties into the vehi...

Heater Blower Duct Seal for diesel applications, fitted in the heater air intake. This foam seal sits between the air inlet duct and the heater blo...

J Bolt for the battery clamp - battery mounting and hold-down. The hooked end of the bolt engages the battery tray or platform and the threaded en...

Bulkhead Mudshield, left-hand - inner wing to bulkhead splash plate, right-hand drive applications. The mudshield closes the gap between the inner...

Bulkhead Mudshield, right-hand - inner wing to bulkhead splash plate, right-hand drive applications. The mudshield closes the gap between the inne...

Door Seal - Bottom for the left-hand front door, forming part of the door-aperture weather sealing. The seal fits along the lower edge of the door...

Fuel Injector for the multi-point fuel injection system, mounted in the inlet manifold with its nozzle directed at the back of the inlet valve. Th...

Inlet Manifold Seal for the 4.4L AJ V8 petrol engine, sealing the lower inlet manifold to the cylinder head within the air induction system. It cl...