Land Rover Parts

Rotor Arm for the distributor ignition system. The rotor arm mounts on the top of the distributor shaft and turns with it. It picks up the high-te...

Column Switch mounted on the steering column, combining the indicator (turn signal), horn and headlamp dip/main-beam functions in a single stalk-op...

Water Pump from the engine cooling system of the Td5 2.5L 5-cylinder turbo diesel. It circulates coolant through the cylinder block and cylinder h...

Swivel Pin Housing Joint Washer for the front axle swivel housing assembly. This joint washer seals the oil seal retaining plate to the face of th...

Rear Mudflap - exterior splash guard that mounts behind the rear wheel to deflect mud, water and road debris away from the underbody and following ...

Speedo drive oil seal LT230

Bolt securing the bulkhead to the chassis outrigger. A 1/2" UNF hex-head bolt used at the lower bulkhead mounting points, where the bulkhead fixes...

Joint Washer sealing the mounting joint between the cylinder block and the auxiliary unit driven off the engine: the vacuum pump on diesel engines,...

Injector O-Ring for the 2.5L Td5 5-Cylinder Turbo Diesel fuel injection system. This O-ring seats in the groove on the injector body at the cylind...

Power Steering Pipe for the power steering hydraulic circuit, forming the low-pressure return line that carries fluid from the steering box back to...

Shock Absorber Turret Bracket is the front suspension turret that caps the coil spring and carries the upper mounting of the front shock absorber. ...

Coolant Temperature Transmitter - Black mounted at the thermostat housing, supplying the coolant temperature signal to the instrument cluster tempe...

P-shaped sill seal, 1983 - 1994

Slipper pad

Steering Column Switch - Wash/Wipe - the column-mounted stalk switch that operates the windscreen wiper and washer functions. Mounted on the steer...

Centre Cubby Box finished in black vinyl, fitting the centre position between the front seats to provide an enclosed storage compartment with a mou...

Clutch Pedal Assist Spring Kit - an over-centre helper spring for the clutch pedal that reduces the effort required to operate the clutch. Mounted...

Condenser for the distributor ignition system. The condenser (capacitor) is wired across the contact breaker points inside the distributor. As the...

O-Ring for the oil filter adaptor assembly on 4-cylinder petrol and diesel engines up to and including the 300TDi. This O-ring seals the joint bet...

T-piece imperial

Transfer Box Flange Bolt - a 3/8" UNF x 1-1/4" hex-head bolt for the LT230 transfer case front output flange. It secures the drive flange to the f...

Fitment: All models from (VIN) WA138480 on

Panhard Rod Bush from the front suspension's lateral location linkage. The Panhard rod controls sideways movement of the axle relative to the body...

Rear Screen Washer Jet for the rear screen washing system, mounted at the tailgate window. It directs washer fluid delivered by the washer pump on...

Exhaust Front Pipe for the 2.25L petrol engine, forming the first section of the exhaust system between the manifold and the intermediate pipe. It...

Gerschikt voor 2.25 ltr benzine

Crankshaft Oil Seal - Front seals the nose of the crankshaft where it passes through the timing cover on the Td5 2.5L 5-cylinder turbo diesel engin...

Radius Arm Cup Washer is the dished washer used at the front radius arm mounting, seating against the radius arm bush to spread the clamping load o...

Rear Axle Half Shaft - RH, part of the disc-braked Salisbury rear axle assembly. The right-hand halfshaft transmits drive from the differential si...

Compression Olive for rigid fuel pipe unions. This 8 mm ferrule seats between the union nut and the fitting body, compressing onto the pipe as the ...

Seat Tipping Knob for the front seat back tipping-release mechanism. Threaded knob fitted to the seat frame; turning it disengages the seat back c...

Engine Mounting Rubber is a bonded rubber-to-metal isolator in the powertrain mounting assembly. It sits between the mounting bracket and the chass...

Bolt - a metric hexagon-head bolt measuring M10 x 110mm. This is a general-purpose threaded fixing used at structural and chassis mounting points,...

Split Pin used throughout the chassis, steering and driveline assemblies as a positive locking fastener. The pin is passed through a cross-drilled...

Handbrake Shoe Set for the transmission-mounted drum handbrake. The shoes expand against the drum at the transfer box output to hold the vehicle w...

Distributor Cap for the Lucas distributor fitted to the four-cylinder petrol engine, part of the ignition system. The cap seats over the distribut...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Plastic Rivet in black, a push-in fastener for door cards, interior trim panels and wheelarch eyebrow trims. Locates through a pre-drilled hole an...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Rocker Cover Gasket for the 2.5L 300TDi diesel engine, sealing the interface between the rocker cover and the cylinder head. Installed at the top ...

Plain washer

Exhaust Manifold bolts to the exhaust ports on the cylinder head and collects the exhaust gases from the cylinders into a single outlet feeding the...

Handbrake Gaiter - round-hole type - for the transmission handbrake (parking brake) lever assembly. This rubber gaiter fits over the base of the L...

Radiator Hose - Top - 2.25 Petrol is the upper coolant hose connecting the thermostat housing outlet to the inlet of the radiator header tank in th...

Bolt, 1/4" BSF x 1", serving as the steering lockstop in the front axle steering assembly. The bolt threads into the swivel housing and is set to l...

Pedal Box Gasket for the pedal box housing assembly. Seals the mounting joint between the clutch and non-servo brake pedal housing and the bulkhea...

Drive Shaft Housing Bolt securing the drive shaft (swivel/stub axle) housing to the axle case. An M10 double-hex (twelve-point) headed bolt used a...

Brake Drum - 11 in - Large Wheel Studs is a cast iron drum for the drum brake assemblies of Series 3 and Defender models. The drum measures 11 inc...