Land Rover Parts

Lambda Sensor - heated oxygen sensor fitted in the exhaust system of the 2.2L Puma TDCi diesel engine. It measures the residual oxygen content of ...

Bolt used within the clutch and flywheel assembly of the 2.2L Puma TDCi diesel engine. Serves as a mounting fastener in the flywheel and clutch in...

Cooling Fan for the 2.2L Puma TDCi diesel engine - a viscous coupling with an integral fan blade that mounts on the water pump drive. The temperat...

Glow Plug

Water Outlet Connection is the coolant outlet fitting on the oil cooler and filter housing of the 2.2L turbo-diesel (Puma) engine. It routes coola...

Bumper Bracket Mounting

Bumper Bracket Mounting

Windshield Moulding

Front Door is a complete steel front door assembly for the left-hand (LH) side. Built around a pressed-steel frame and outer skin, it is configure...

Power Steering Hose is the pressure line in the power steering hydraulic circuit. It carries pressurised fluid from the power steering pump to the...

Shock Absorber Insulator – Rear is the rubber isolating pad fitted at the rear shock absorber mounting. It seats at the shock absorber mount to cu...

Crankshaft Seal & Retainer – Rear is the rear main oil seal together with its carrier plate, mounted to the rear face of the cylinder block on ...

Rubber Pad is a butyl sealing pad used in the body sealing system to block water ingress at the lower body and door seal interface. The pliable bu...

Door Check Strap is the front door check link that controls how far the door opens. Mounted between the door and the A-pillar, it limits door trav...

Gas Strut supports the tailgate on the right-hand side, one of the gas-filled struts that carry the tailgate on its hinges. The strut extends unde...

Body Moulding Clip - a plastic retaining clip that secures exterior body mouldings to the body panels. It engages a locating hole in the panel and ...

Trim Clip - push-fit fastener securing exterior body mouldings, front and rear bumper trim and the radiator grille to the body panels. Renews an o...

Plastic Rivet is a push-fit fastener that secures front engine-compartment insulation panels to the body. It locates into a pre-formed panel hole t...

Name Plate is a moulded plastic exterior badge fitted to the body panel.

Exhaust Manifold Gasket seals the exhaust manifold to the cylinder head on the 2.0L 16V petrol engine. Fitted between the head's exhaust ports and...

Bumper - Rear

Starter Motor

Tailgate Gas Strut supports the raised tailgate (luggage compartment door), holding it open and damping its movement. Gas-charged strut for vehicl...

Exhaust Rubber Mount (insulator) that suspends the exhaust system from the underbody. The flexible rubber isolates exhaust vibration and noise from...

Crankshaft Damper Washer for the 2.0L 16-valve turbocharged petrol engine, fitted in the crankshaft damper assembly at the front of the timing gear...

Transmission Oil, SAE 75W, meeting specification BOT 352, supplied in a 1 L bottle. For the 6-speed manual transmission (M66) and, on hybrid appli...

Front Lower Engine Mounting is the lower insulator supporting the engine at the front of the mounting system. It locates the engine to the subfram...

Upper Knuckle Bolt is a hex-head bolt that retains the upper knuckle joint within the hub and knuckle assembly. It clamps the upper knuckle to the...

Lower Knuckle Bolt, a hex-head M12 x 130 mm bolt for the front knuckle and hub assembly. It retains the lower end of the knuckle, clamping it to t...

Hub Bearing Circlip for the rear hub assembly. The circlip locates in a groove in the rear knuckle to retain the wheel bearing in its housing, hol...

Coil Spring for the front suspension. The coil spring supports the vehicle's weight at the front axle and maintains ride height, working with the ...

Shock Absorber for the front suspension. The damper forms part of the front strut assembly, controlling spring oscillation and wheel movement to k...

Sensor Assembly

ABS Sensor - Front for Defenders equipped with automatic transmission. This wheel speed sensor mounts at the front axle hub and continuously monit...

Ride Height Sensor for the rear axle, part of the electronic air suspension system. The sensor links the vehicle body to the rear suspension arm a...

Ride Height Sensor for the front of the electronic air suspension system. It measures the position of the front suspension arm relative to the body...

Hex-Head Bolt, M12 x 80 mm for the accessory drive of the 2.2L Puma turbo-diesel engine. The bolt secures components in the pulley and drive-belt ...

Sealing Washer for the 4.4L DOHC DITC V8 diesel (TDV8). Seals a connection at the right-hand (primary) turbocharger. Renew on reassembly to ensure...

Exhaust Gas Temperature Sensor for the diesel particulate filter (DPF) system. Monitors exhaust gas temperature in the after-treatment section and...

EGR Gasket for the 2.2L diesel engine, part of the exhaust gas recirculation (EGR) system. Seals a joint in the EGR circuit, maintaining a gas-tig...

Cylinder Head Bolt for the 2.2L diesel engine, clamping the cylinder head to the engine block. The bolt passes through the cylinder head and threa...

Brake Pad Set is a set of front disc brake friction pads for the front-axle braking assembly. The pads locate in the front brake calipers and are ...

Engine Mounting (mounting insulator) for the 2.2L diesel engine, part of the powertrain mounting system. It combines a bonded rubber element with m...

Wire Assembly - Connector Only

Wire Assembly

Outer Door Handle is the exterior handle for the side doors and fits both front and rear positions. This version is for vehicles equipped with the...

Crankshaft Oil Seal is the rear crankshaft (rear main) oil seal for the 2.2L and 2.4L Duratorq TDCi Puma diesel engine. It seals the rear of the c...

EGR Gasket Inlet